Manuals / Brands / Household Appliance / Smoke Alarm / Honeywell / Household Appliance / Smoke Alarm

Honeywell MS-9200UDLS, MS-9200UDLSE 2.9.1 4XTMF Transmitter Module Installation

1 188

Download 188 pages, 2.42 Mb

Installation

Optional Module Installation

2.9.1 4XTMF Transmitter Module Installation

The 4XTMF provides a supervised output for a local energy municipal box transmitter in addition to alarm and trouble reverse polarity. A jumper option allows the reverse polarity circuit to open with a system trouble condition if no alarm condition exists. A disable switch allows disabling of the transmitter output during testing to prevent accidental calling of the monitoring service.

Local Energy Municipal Box Service (NFPA 72 Auxiliary Fire Alarm Systems): Supervisory Current: 5.0 mA

Trip Current: 350 mA (subtracted from notification appliance power)

Coil Voltage: 3.65 VDC

Maximum Coil Resistance: 14.6 ohms

Maximum allowable wire resistance between panel and trip coil: 3 ohms Municipal Box wiring can leave the building

Remote Station Service (NFPA 72 Remote Station Fire Alarm Systems) - Intended for connection to a polarity reversal circuit or a Remote Station receiving unit having compatible ratings:

Maximum load for each circuit: 10 mA

Reverse polarity output voltage: 24 VDC

Remote Alarm and Remote Trouble wiring can leave the building

Before installing the module, place the disconnect switch to the right (disconnect) position to prevent accidental activation of the municipal box. Note that a Disconnect LED will illuminate after the module is installed in the MS-9200UDLS. In addition, the System Trouble LED will turn on to indicate the Disconnect condition.

Note: 4XTMF Module is not suitable for

transmitting reverse polarity supervisory signal.

}Remote Alarm (power-limited)*

* Wiring from these

terminals can exit the

}Remote Trouble (power-limited)*

protected premises.

No connection

Dummy load terminals

6 and 7 (4.7kΩ, ¼ watt

}Municipal Box (nonpower-limited)*

resistor) if Municipal

+

-

-

Box is not connected.

+

-

+

1

2

3

4

5 6

7

Polarities are shown for module activation

Disconnect LED

4xtmfl.cdr

Disconnect Switch shown in disconnect position

TBL Jumper

Connect to FACP J10 & J11

Figure 2.15 4XTMF Transmitter Module

38	MS-9200UDLS PN 52750:A 11/04/05

Contents

Fire Alarm Control Panel IMPORTANT Page Page Notes SECTION 1: Product Description SECTION 2: Installation SECTION 3: Programming Page SECTION 4: Operating Instructions SECTION 5: Central Station Communications SECTION 6: Remote Site Upload/Download SECTION 7: Power Supply Calculations APPENDIX A: Software Zones APPENDIX B: Default Programming NFPA Standards Underwriters Laboratories Documents: Other: Fire-LiteDocuments: Basic System Connections Page Product Description AC Power - TB11 Page EIA-485(TERM) or EIA-232(ACS) - TB8 EIA-485(ACS) - TB9 1.2.1 Current Availability Figure 1.1 Current Availability HONEYWELL LIFE SAFETY SYSTEM ALL NORMAL 10:00A LCD Display LED Indicators Key Panel SLC Communication Loop Output Circuits NAC (Notification Appliance Circuits) Relays Main Circuit Board Cabinet Transformer Assembly Batteries 1.6.1 Intelligent Addressable Detectors: Newer Series 1.6.2 Intelligent Addressable Modules: Newer Series 1.6.3 300 Series Intelligent Addressable Devices 1.6.4 Addressable Device Accessories End-of-LineResistor Assembly Power Supervision Relay 4XTMF Transmitter Module 1.8.1 PK-CDProgramming Utility 1.8.2 Dress Panel 1.8.4.1CHG-75Battery Charger 1.8.4.2 CHG-120FBattery Charger 1.8.5 Annunciators ACS Series LED Zone Type Annunciators ACM-16ATF AEM-16ATF AFM-16ATF LCD-80FRemote Fire Annunciator LDM Series Lamp Driver Modules (Graphic Annunciator) 1.10.1Telephone Circuitry 1.10.2Digital Communicator MS-9200UDLS US:1W6AL00B9200UD 0.0B 1.10.3Telephone Company Rights and Warnings 1.10.4For Canadian Applications CAUTION Installation Figure 2.2 MS-9200UDLSMain Board/Chassis Installation Figure 2.3 MS-9200UDLSCabinet Mounting Page WARNING: 2.3.1 AC Power and Earth Ground Connection 2.3.2 Battery Power 2.3.3 Special Application DC Power Output Connection Figure 2.5 Special Application Power Outputs - 24 VDC TB7 TB5 TB6 Figure 2.6 Relay Terminals 2.5.1 Configuring NACs Figure 2.7 NAC Configuration Using NACKEY 2.5.2 Style Y (Class B) NAC Wiring Figure 2.8 NAC Style Y (Class B) Wiring 2.5.3 Style Z (Class A) NAC Wiring Figure 2.9 NAC Style Z (Class A) Wiring Figure 2.10 Remote Sync Output Figure 2.11 Typical UL Power-limitedWiring Requirements *Ferrite Bead Installation Figure 2.12 DACT Installation Figure 2.13 Wiring Phone Jacks WARNING MS-9200UDLSKeypad/Display Removal Figure 2.14 Keypad/Display Removal 2.9.1 4XTMF Transmitter Module Installation Figure 2.16 4XTMF Connectors to MS-9200UDLSConnectors 2.9.2 Printer/PC CAUTION Installation Figure 2.17 Serial Printer and Computer Connections Printer Configuration 2.9.3.1ACM-8RFRelay Control Module 2.9.3.2 ACS and AFM Series Annunciators Programming Autoprogramming Feature SYSTEM ALL NORMAL 10:00A 1=READ STATUS MODE 2=PROGRAMMING MODE User Programming Levels TROUBL IN SYSTEM NO DEVICES INSTALLED 09:03A 1=READ STATUS MODE 2=PROGRAMMING MODE 3=MANUAL DIAL MODE PROGRAMMING ENTER PASSWORD Master Maintenance Programming Screen #1 PROGRAMMING 1=LOOP SETUP 2=SYSTEM SETUP 3=VERIFY LOOP Programming Screen #2 PROGRAMMING 1=HISTORY 2=WALKTEST 3=OPTION MODULES 3.6.1 Autoprogram AUTOPROGRAM AUTOPROGRAMMING PLEASE WAIT Autoprogram Progress Screen 3.6.2.1 Detector Programming DETECTOR# IS ADDED 3.6.2.1.2 Delete Detector DELETE DETECTOR Delete Detector Screen NO DETECTOR INSTALLED Edit Detector Screen #1 TROUBL SMOKE(PHOTO) <ADJ><NOUN ZNNN EDIT DETECTOR 1D017 1=ENABLED YES 2=TYPE SMOKE(PHOTO) 3=VERIFICATION OFF Edit Detector Screen #2 1=WALKTEST NO 2=PASNO DETECTOR TYPE 1=SMOKE(PHOTO) 2=USER-DEFINED-13=SMOKE (ION) Detector Type Screen #1 Verification Walktest PAS Pre-signal Zone Assignment ZONE ASSIGNMENT Z00 Z** Z** Z** Z Zone Assignment Screen Noun/Adjective 1=NORTH 1=3RD 2=SOUTH 2=4TH 3=EAST 1=BASEMENT 1=KITCHEN 2=BOILER RM 2=LOBBY 3=CLASSROOM Description DESCRIPTION 1D002 1=NOUN/ADJECTIVE Adjective/Noun Screen Recall/Increment Function 3.6.2.2Module Programming MODULE# Add Module Screen #3 3.6.2.2.2 Delete Module DELETE MODULE ENTER MODULE# Delete Module Screen NO MODULE TROUBL MONITOR <ADJ><NOUN *1M012 NORMAL MONITOR <ADJ><NOUN ZNNN W 1M012 ZNNN 1M012 EDIT MONITOR 1M012 1=ENABLED YES 2=TYPE MONITOR Edit Monitor Screen #2 1=PRE-SIGNALNO Enable/Disable Module Type Monitor MONITOR TYPE 1=PULL-STATION 2=USER-DEFINED-1 3=WATERFLOW Monitor Type Screen #1 Table 3.1 Monitor Types MON ZONE ASSIGN 1=FLOOR 2=FLOOR 1=GARAGE 2=HALLWAY 1=ZONE DESCRIPTION 1M012 1=NOUN/ADJECTIVE 3.6.2.2.4Edit Module Screen for Control Modules NORMAL CONTROL <ADJ><NOUN SW 1M002 Edit Control Screen #1 EDIT CONTROL 1=ENABLED YES 2=TYPE CONTROL 3=SILENCEABLE YES Edit Control Screen #2 Edit Control Screen #3 CONTROL TYPE 1=BLANK 2=BELL-CIRCUIT 3=HORN-CIRCUIT Control Type Screen #1 Silenceable Page Page DESCRIPTION 1M002 1=NOUN/ADJECTIVE 3.6.3.1 Enable 3.6.3.2 Disable 3.6.3.3 Zone 97, 98 and 3.6.3.4 Zones Installed 3.6.3.5 Zones Enabled 3.6.3.6 Zones Disabled 3.6.3.7 Zone Type 3.6.3.8 Zones Available 3.6.4.1 Style 3.6.4.2 Loop Protocol 3.6.5 System Setup SYSTEM SETUP 1=TROUBLE REM OFF 2=BANNER 3=TIME-DATE System Setup Screen #1 SYSTEM SETUP 1=TIMERS 3.6.5.1 Trouble Reminder 3.6.5.2 Banner 3.6.5.3 Time-Date WEEK 3.6.5.4 Timers Pre-signalDelay PRESIGNAL DELAY Pre-signalDelay Screen 3.6.5.4.3 Waterflow Delay WATERFLOW DELAY 3.6.5.5 NAC (Notification Appliance Circuit) 2=TYPEBELL NAC Screen #1 1=AUTO SILENCE 2=CODING TEMPORAL 3.6.5.5.2 Type NAC TYPE 1=BELL 2=HORN 3=STROBE 3.6.5.5.4 Auto Silence AUTO SILENCE 1=NO 2=5 MINUTES 3=10 MINUTES Auto Silence Screen #1 AUTO SILENCE 1=15 MINUTES 2=20 MINUTES 3=25 MINUTES 3.6.5.5.5.1 Two Stage Operation 3.6.5.5.6 Zone Zone Screen 3.6.5.5.7 Silence Inhibited 3.6.5.5.8 Sync Type NAC SYNC TYPE 1=SYSTEM SENSOR 2=WHEELOCK 3=GENTEX 3.6.5.6 Relays 3.6.5.7 Canadian Option 3.6.5.8 Waterflow Silenceable 3.6.7.1 View Events 3.6.7.2 Erase History 3.6.8 Walktest WALKTEST 1=SILENT 2=AUDIBLE 3=VIEW RESULT 3.6.9.1 Annunciators/UDACT 3.6.9.2 Onboard DACT 3.6.9.2.2 Primary Phone PRIMARY PHONE LINE 1=TYPE TOUCHTONE Primary Phone Line Screen PHONE LINE 3.6.9.2.4 Service Terminal SERVICE TERMINAL 1=PANEL ID 0000 2=TERMINAL 1 3=TERMINAL Service Terminal Screen #1 1=RING COUNT 3.6.9.2.4.2 Terminal 1 and Terminal SERVICE TERMINAL # 1=PHONE NUMBER Service Terminal # Screen Phone Number (Service Terminal) PHONE NUMBER 3.6.9.2.4.3 Ring Count RING COUNT 0-25RANGE Ring Count Screen 3.6.9.2.5 Central Station 3.6.9.2.5.2 Backup Reporting BACKUP REPORTING 1=BACKUP ONLY 2=BOTH 3=FIRST AVAILABLE Backup Reporting Screen 3.6.9.2.6 Trouble Call Limit (Dialer Runaway Prevention) 3.6.9.2.6.1Central Station Primary and Secondary Phone Numbers CENTRAL STATION # 1=TEST TIME INT 24 2=ACCOUNT CODE 0000 3=24HR TST TIME Primary/Secondary Screen #1 CENTRAL STATION 1=PHONE NUMBER Test Time Interval TEST TIME INTERVAL 1=24 HOURS 2=12 HOURS 3=8 HOURS Test Time Interval Screen #1 24 Hour Test Time 24 HOUR TEST TIME 24 Hour Test Time Screen Phone Number Phone Number Screen Communication Format COMM FORMAT 1=ADEMCO EXPRESS 4P1 2=ADEMCO EXPRESS 4P2 3=3P1S C18 A23 Comm Format Screen #1 COMM FORMAT 1=3P1E C18 A23 2=3P1S C19 A14 3=3P1E C19 A14 Table 3.1 Communication Formats Event Codes EVENT CODES 1=PULL STATION 2=MON-USER-DEF-1 Event Code Screen 3+1, 4+1 Express and 4+1 Standard Table 3.2 Event Codes Table 3.2 Event Codes (continued) 4+2 Standard, 4+2 Express, 3 + 1, 4 + 1 and 4+2 Expanded Formats Table 3.3 Event Codes Table 3.3 Event Codes (continued) Ademco Contact ID Format Table 3.4 Event Codes Table 3.4 Event Codes (continued) Report Style 3.6.9.2.7 Manual Dial Mode MANUAL DIAL MODE 1=PRIMARY PHONE 2=SECONDARY PHONE MANUAL DIAL MODE 1=GO OFF HOOK 2=DIAL DIGIT(S) 3=GO ON HOOK 3.6.9.3 Printer/PC MASTER 3.6.11 Clear Program CLEAR PROGRAM 1=WHOLE SYSTEM 2=ALL POINTS Clear Program Screen #1 WARNING SYSTEM CHANGE 3.6.12 Program Check PROGRAMCHECK 1=NACS NO INPUT 2=ZONES NO INPUT 3=ZONES NO OUTPUT NACS NO INPUT NAC ZONES NO INPUT 05 07 09 10 11 1M001 ZONES NO OUTPUT 05 07 09 10 11 1D001 1=READ STATUS 2=PROGRAMMING PROGRAMMING 1=WALKTEST 2=SYSTEM 3=ZONE SETUP 3.7.1 Disable Point POINT PROGRAM 1=DETECTOR 2=MODULE Device Select Screen Address Select Screen EDIT DETECTOR 1D001 3.7.2 History Events Screen PROGRAMCHECK 1=NACS NO INPUT 2=ZONES NO INPUT 3=ZONE NO OUTPUT 3.7.4 Walktest 3.7.5 System SYSTEMS 1=TIME/DATE System Screen TIME AND DATE 1=TIME 01:00 AM 2=DATE 12HR Time and Date Screen 01:00 AM 1=AM 3.7.6 Zone Setup Zone Setup Screen SPEC PURPOSE ZONE 1=PAS OFF 2=PRE-SIGNAL98 Operating Instructions AC Power Fire Alarm Supervisory Trouble Maintenance HONEYWELL LIFE SAFETY SYSTEM ALL NORMAL 10:00A Addressable Smoke Detectors, Monitor Modules and Control Modules TROUBL SMOKE (PHOTO) <ADJ> <NOUN INVREP 10:00A 010801 1D001 Z000 10:00A 010801 1M001 ACTIVE SUPERVISORY <ADJ> <NOUN Page Maintenance Alert Automatic Test Operation Type Code Supervision System Alarm Verification Smoke Detector Data Page Page 4.20.1 Silence Inhibit Timer 4.20.2 Autosilence Timer 4.20.3 Trouble Reminder 4.20.4 Waterflow Retard Timer 4.20.5 Alarm Verification (None or One Minute) Alarm/Shorted Condition Open Condition Read Status Entry READ STATUS 1=SYSTEM POINT 2=ZONES 3=POWER Read Status Screen #1 1=TROUBLE REMINDER 2=TIMERS 3=NACS 4.22.1 System Point READ SYSTEM POINT NORMAL SMOKE(PHOTO) NORTH CLASSROOM Z005 4.22.2 Zones ZONES Zones Screen #1 1=SPECIAL PURPOSE 2=ZONE TYPE 3=ZONE MESSAGE Zones Screen #2 4.22.3 Power BATTERY 24 V RST Power Screen #1 CHARGER 4.22.4 Trouble Reminder TROUBLE REMINDER TROUBLE REM 4.22.5 Timers PAS 4.22.6 NAC 4.22.7 Relays 4.22.8 Program Check PROGRAM CHECK 1=NACS NO INPUT 2=ZONES NO INPUT 3=ZONES NO OUTPUT 4.22.9 History 4.22.10 Annunciators ANNUNCIATORS TERM ENABLED ACS ENABLED UDACT ENABLED 4.22.12 Central Station CENTRAL STATION REPORTING ENABLED REPORT 4.22.13 Service Terminal SERVICE TERMINAL PANEL ID 2=TERMINAL 1 3=TERMINAL 4.22.14 Printer/PC PRINTER PC PRINTER PC PR4800 4.22.15 Print PRINT 1=HISTORY 2=WALKTEST LOG 3=DETECTOR DATA 1=EXIT PRINTING Drift Compensation Table 4.1 Maintenance Alert Levels DIRTY Acceptable Range 4.22.16 Time-Date START APR WEEK WEEK-1 SECTION 5 Central Station Communications Table 5.1 Format Selection Table 5.2 Format Selection Address Explanation Page Table 5.3 Compatible UL Listed Receivers Remote Site Upload/Download 6.1.1 Security Features Secret Code Verification Time-outat Control Panel Callback to Service Terminal Panel Identification Number Error Checking Central Station Acknowledge Central Station Data Protection Page Page Power Supply Calculations 7.3.1 Overview Table 7.2 Converting to Full Amperes Table 7.3 System Current Draw Calculations Table 7.4 Total Secondary Power Requirements at 24 VDC 7.4.1 NFPA Battery Requirements 7.4.2 Selecting and Locating Batteries Page Correlation of Input and Output Zones Input Devices Zones Output Devices Table A.1 Detector Programming Sheet Example Table A.2 Module Programming Sheet Example Table A.3 Blank Detector Programming Sheet - 1 of Table A.4 Blank Module Programming Sheet - 1 of Page MS-9200UDLSControl Panel Initiating Devices Notification Appliances NFPA 72 NATIONAL FIRE ALARM STANDARDS FOR: NFPA 72 Central Station Service (Protected Premises Unit) or Remote Station Page NFPA 72 Remote Station Protective Signaling System NFPA 72 Proprietary Protective Signaling Systems MS-9200UDLS Addressable Fire Control Panel MS-9200UDLSMain Board Table D.1 MS-9200UDLSWire Specifications E.1.1 HVAC SHUTDN HVAC SHUTDN E.2.1 HVAC RESTART HVAC RESTART E.2.2 HVAC OVRRIDE HVAC OVRRIDE Numerics C cabinet