Mounting and Wiring, Site Preparation | Honeywell UMC800 specs

Mounting and Wiring

Site Preparation

Mounting and Wiring

Site Preparation

The UMC800 must be mounted within an enclosure. Hardware is provided to surface mount the controller to a panel or other suitable surface. Be sure that there is sufficient clearance for mounting the controller enclosure and the external wiring.

UMC enclosure and components

The controller enclosure houses all circuit assemblies of the UMC controller. See Figure 7. The power supply and CPU are modules that plug into slots on the right hand side of the enclosure. Both modules have metal covers on the front where indicators, switches and connectors are located. All external connections to the power supply and CPU are made on the front panels of these modules.

A front cover can be removed by two screws to access the I/O modules. There are two rows of card guides to accommodate up to 16 plug-in I/O modules. External signal wiring to field devices are made with removable terminal blocks that attach to the front of each I/O module. Optional terminal strips can be used to provide shield termination of field wiring.

Power supply, CPU and I/O modules are connected through a common backplane within the enclosure. All external wiring for power supply and I/O modules are brought out through rubber grommets located at the top and bottom of the enclosure. The CPU features two connections for external communications. One provides a cable connection to a PC for configuration and database file management; the other connection accommodates a cable to the operator interface. An optional communication board provides two RS 485 serial communications ports (slave and master) using Modbus RTU protocol.

External Wiring

Access Holes

Front

Cover

CPU Module

Power Supply

Figure 7 UMC800 controller enclosure

Release F	UMC800 Controller Installation and User Guide	15
4/01

Image 23

Honeywell UMC800 manual Mounting and Wiring, Site Preparation, UMC enclosure and components

Contents

UMC800 Controller Copyright 2001 by Honeywell Release F April Warranty/Remedy Contacts About This DocumentAbstract References Symbol Definition Symbol Definitions Contents Maintenance Tables Figures Description IntroductionPurpose Topic CE Conformity Europe UMC800 Controller UMC800 Description UMC800 Overview − ON/OFF Feature Summary Enclosure Equipment IdentificationController Components Control architecture ModulesController plug-in I/O module types 551 operator interface Operator Interface Typical Control Builder graphic display Control Builder User utility Control Builder on-line help Communication port descriptions Communication Port On CPU Module Configuration DisplaySerial Communication Ports Operating limits Pre-Installation ConsiderationsSpecifications Introduction Controller grounding Taking electrical noise precautionsElectrical considerations Bundle No Permissible wire bundlingPermissible wiring bundles Wire Functions Pre-Installation Considerations Introduction UMC enclosure and components Mounting and WiringSite Preparation Assembling parts Power requirementsPower supply input requirements Mounting the Controller UMC800 controller enclosure dimensions Enclosure mounting dimensions Common backplane Plug-in Module Locations Part Number Module Type ID NumberTerminal Block Color Maximum Allowed O module installation limitationsModule limits Slot Locations See Figure Controller Slot # Module Type Module ID 8001 000 0E 01122300Controller model number Example of controller model number Module identification record Verify I/O module locations Module wiring Signal Wiring Field wiring shield termination Analog input / analog output field wiring Analog inputs module ID Universal analog input module specificationsSpecification Description Recommended wiring for one pH sensor input Field wiring for one pH sensor input module ID C AO module terminal block connections Analog outputs module ID Digital inputs DI module terminal block connections Do module terminal block connections Digital outputs Digital Output Module Do module relay contact setting PI/FI module terminal block connections Pulse input/frequency input module with digital outputs Pulse/frequency input connections Pulse input/frequency input jumpers Max Pulse Frequency Typical Filter Jumper Setting Pulse Width RangeSupply Return Pulse/frequency card digital output connections Pulse frequency card outputs Serial communications ports Wiring Communication Links Summary of communication link connections to controller Configuration connectorConfiguration connector pinouts Order part number Configuration cable Null modem cable constructionPC Connector Pin D Female UMC800 Pin D Male Quantity Description Installing ferrite clamp for CE compliance Operator interface connector pinouts Display connector to operator interface Terminal connections Connector location at the rear of the operator interface Shield Receive Transmit Comm a and B connectors optional RS 485 serial communications RS 485 port wiring 2 wire Cable requirements Remote AccessOverview Modem requirements Modem configuration 3Com US Robotics 56K Data/Fax External Modem Modem configuration examples Set the modem switches to the following Zoom 56K Dualmode External Modem Best Data 56SX Data Fax External Modem SixNet VT-MODEM Industrial External Modem Prepower checks Power Supply WiringPower supply wiring Ground wiring Operation Power Up / Power DownPower-up Power-down Mode control Program modeRUN mode Offline mode Controller mode switch location Restrictions on mode control Controller Mode Manual Switch setting Controller mode switch summarySetting mode switch to Program and then to RUN Calibration Yes Real-time Clock Change File DownloadingController downloading summary Code Download Cold start Scan rates per inputs configuredWarm Start / Cold Start Warm start Controller status LEDs Status IndicatorsStatus LEDs Controller status LEDs Controller Status Alarm and status blocks Comm port status RS 485 Port Configuration Communication Board OptionComm a and B ports UMC800 Controller Installation and User Guide Release F Servicing MaintenanceWarranty Overview Battery replacement Routine MaintenanceController maintenance Calibration overview Controller Calibration Controller components that contain calibration values Factory calibration AI module calibration Calibration proceduresField calibration AO module calibration values Maintenance Controller Calibration Thermocouple Input AO module jumper ST1 Controller components and location Replacement Procedures Maintenance Replacement Procedures Step Action Remove power from the controller Replacing the power supply fuse For the standard CPU module Replacing the battery Replacing I/O modules Step Action Remove power from controller Step Action Replacing the power supply module Replacing the backplane Step Action Power up diagnostics Diagnostics and TroubleshootingController Diagnostics Meaning Diagnostic displaysStatus LED Details of the diagnostic summary display Fault Detection and Troubleclearing System Task Fault CPU Memory Good LOW Battery Flash Error RTC RTC Read Failure Panel Normal Menu Status Fault detection and troubleclearingDetails of the I/O module diagnostics display Module Diagnostics Module BAD Module Modem does not answer Cause Solution Modem troubleshootingController modem troubleshooting UMC800 Controller Installation and User Guide Release F Part Description Parts ListReplacement parts Part Description Controller Design SpecificationsModule Configuration DC Inputs Component Analog OutputsDigital Inputs AC Inputs DC Outputs Component Parameter Description Logic InputsDigital Outputs AC Outputs Time Proportional Outputs TPO Relay Alarm Outputs Design Product Classification Enclosure Rating Transportation Storage Environmental and Operating ConditionsRated Extreme Type RH Type RI PV InputsW5W26 Honeywell Radiamatic Millivolts Volts Carbon Oxygen OhmsLinear Milliamperes 102 UMC800 Controller Installation and User Guide Release F Index Index Y, Z DA2I-6048 Sikkerheskrav DU2I-6048 Veiligheidsvereisten FI2I-6048 Turvallisuusmääräykset FR2I-6048 Consignes DE Securite GE2I-6048 Sicherheitshinweise ¹¬¸ª¸ ¸»ª¸ IT2I-6048 Norme DI Sicurezza NO2I-6048 Sikkerhetskrav PO2I-6048 Instruções DE Segurança SP2I-6048 Normas DE Seguridad SW2I-6048 SäkerhetsföreskrifterPage Austria Denmark Italy Argentina Bulgaria GermanyAsia Pacific Canada Hungary Australia Czech Republic Iceland Portugal Russia Turkey NorwayRepublic of South Sweden Africa Poland Romania SwitzerlandPage Sensing and Control