Specifications, Video specifications | Insignia HRSD16 specs

Specifications

		J
Specifications

	Video specifications

	Signal Format	NTSC or PAL (Auto Detect)

	Video Input	Composite: 8 or 16 looping inputs, 1 Vp-p,
		auto-terminating, 75 Ohms

	Monitor Outputs	Composite: 1 BNC, 1 Vp-p, 75 Ohms
		SPOT: 1 BNC, 1 Vp-p, 75 Ohms
		VGA: 1

	Video Resolution	Composite: 720x480 (NTSC), 720x576 (PAL)
		VGA: 800x600 @ 60Hz

	Record Speed	Up to 120ips (NTSC)/100ips (PAL)
	(images per second)


	Inputs/Outputs

	Alarm Input	8 or 16 TTL, programmable as NC or NO, 4.3V
		threshold

	Alarm Output	2 relay outputs, terminal blocks, programmable
		as NC or NO, 0.5A@125VAC, 1A@30VDC

	Alarm Reset Input	1 TTL, terminal block

	Internal Buzzer	80dB at 10cm

	Network Connectivity	10/100 Mbps Ethernet (RJ-45), RS-232C for
		external modem

	Audio Input	RCA Input: 2, Line In

	Audio Output	RCA Output: 1, Line Out

	Text Input	8 serial text strings (max) interface via USB.
		RS232 port accepts single data stream with
		multiplexed data from up to 8 or 16 terminals.

Document 800-00918 Rev E	153
12/07

Image 153

Insignia HRSD16 manual Specifications, Video specifications, Inputs/Outputs

Contents

HRSD8, HRSD16 Revisions Issue Date Revisions Explanation of Graphical Symbols FCC Compliance StatementCE Compliance Weee Compliance RoHSWeee Waste Electrical and Electronic Equipment Contents Appendix B Text-In Query Examples Appendix a USB Hard Disk Drive Preparation Figures Page Figure B-1 Query Example 135 Figures Tables Tables About This Document Overview of Contents About Cautions and Warnings Page Risk of explosion if battery is replaced by an incorrect Page Lt BT Swiss721Font What it represents Example Keys on the keyboard Press Ctrl+C Introduction Features Technical Overview Typical DVR Installation for the HRSD8/16 DVR Introduction Installation Package ContentsRequired Installation Tools Connecting the Video Source Connecting the Loop Through VideoSerial RS-232C port Power cord connector Connecting the Monitor Connecting AudioUsing a Computer Monitor Using a Spot Monitor Connecting the RS-232C Port Connecting the DVR for Remote AccessConnecting the Network Port RS-232C Port Connecting the RS485 Port Connecting Alarm Inputs and OutputsRS485 Port Ground Connecting USB Ports Factory ResetUSB Ports 13 Power Cord Connector Connecting the Power Cord Installation Front Panel Controls Configuration 16-Channel DVR Front Panel Controls Position Function Channel DVR Front Panel Controls Position Function Position Control Function Channel DVR Front Panel Controls Setup Screen Login ScreenLogging Using the Virtual Keyboard Information ScreenVirtual Keyboard Upgrading the System Software Upgrade Screen Exporting Current DVR Settings Importing Saved DVR Settings Viewing the System Log Setup Export Screen Other Options in the Information Screen Setting Up the Date and TimeInformation Screen Options Action Clear All Data… 11 Holiday Setup Screen Setting Holidays Synchronizing with a Standard Time Server Storage Screen Capacity Formatting a Device for RecordingFormat Information Storage Status Using the Information Column Configuration Viewing All the Users in a Group User Setup ScreenChanging the Authority Levels Assigned to a Group If there is a This means that Adding or Changing a User’s Password Deleting a User or an Entire GroupAdding a Group Setup UpgradeAlarm-Out Control New Group Authority Level Assignments Action Shutdown Options for the New User Adding a User Shutting Down the DVR Network & Notification SetupLogging Out of the DVR Logout Screen Configuring the Network Setting up the Network Configuring the LAN Parameters Manually Setting Up the LAN 25 Port Numbers Setup Screen Using the Current LAN Settings Using Dhcp 26 LAN Dhcp Setup Screen Configuring the LAN Using Adsl 28 Modem Setup Screen Setting Up the Modem Modem Setup Screen Options Option Action Enable Dvrns SetupData Bit Stop Bit Dvrns Server Dvrns Setup Screen Options OptionActionPort Use NAT Configuring Mail Notification Settings Notification Setup Notification Mail Setup Screen Options Option Action Configuring Notification Callback SettingsSender Recipient Retry IP AddressModem Outside Line Call Configuring Devices Configuring the Camera SetupDevices Menu Adding a Camera to the PTZ List 34 Camera PTZ Setup Screen Audio Setup Screen Configuring a PTZ Camera in the Port Setup WindowPTZ Device List 37 Audio Setup Screen Alarm-Out Screen Dwell Time Creating a Schedule for Alarm-Out Display Screen Adjusting the Transparency of the On-Screen Display Adjusting the On-Screen Display Margins Setting Up Sequences for the Display Main MonitorSelecting the Display Sequence for the Main Monitor Defining the Screen Layout Adjusting the Display Dwell Time 43 Spot Monitor Screen Remote Control Screen Recording Settings Record ScreenRecord Menu Resolution Record Setup Screen Options Action RecycleEvent Record Dwell Auto Deletion Scheduling Recording Times Schedule Screen Settings Setting Recording DefaultsDefault… Default Setup Screen Pre-Event Screen 49 Pre-Event Setup Screen Event Settings Alarm-In ScreenEvent Menu Initial settings Setting the DVR Actions in Response to Alarm InputActions 1 Setup Screen Selecting a Camera for Recording Setting Alarm-Out Actions Actions 2 Setup Screen Setting Alarm-In Notifications Associating Spot Monitors with Cameras Selecting PTZ Presets Motion Detection Setup Motion Detection Settings TabAdjusting the Sensitivity of the Motion Detection 56 Motion Detection Sensitivity Screen Defining the Motion Detection Area Motion Detection Zone Setup Screen Menu Adjusting the Motion Ignoring IntervalChanging the Number of Motion Detection Blocks Watching How the DVR Reacts to Motion Setting Up Sensitivity Levels for the Daytime Range Actions 1 Tab settingsMotion Detection Actions Tabs 60 Motion Detection Actions 1 Screen Selecting a Camera or Cameras for Recording Actions 2 Tab settings Setting Motion Detection Notifications Video Loss Screen 62 PTZ Preset Screen 63 Video Loss Settings Screen Setting the Sensitivity for Video Loss 64 Video Loss Actions 1 Screen 65 Video Loss Notify Menu Setting Video Loss Notifications Text-In Screen 67 Text-In Settings Screen 68 Port Setup Screen Page 69 Text-In Actions 1 Screen Setting Text-In Notifications 70 Text-In Actions 2 Screen System Event Screen Setting an Automatic Recording Self-Check Schedule Setting an Automatic System Self-Check Schedule Setting Up Automatic Storage Check-Up Setting an Automatic Alarm-In CheckSetting a Disk Almost Full Notification Checking for Bad Sectors on the Disk 74 S.M.A.R.T Setup Screen Setting Up System Event Actions 75 System Event Actions Screen 76 Event Status Screen Event Status Screen Configuration 102 ZOOM/PTZ Button OperationButton Document 800-00918 Rev E 12/07 Network LED Power LED USB Connectors Active Cameo Mode Using PIP ModeTurning On the Active Cameo Mode Exiting the Active Cameo mode Freeze Mode Zoom ModeAdjusting the Image Browsing with Sequence Mode Entering the Sequence ModeIf you choose After you’ve pressed SEQUENCE, the DVR Exiting Sequence Mode Using a Mouse During Live Monitoring PIP, 2x2, 3x3 Right Mouse Button Menu Functions Option FunctionPrevious Group Next Group Returning to Live Monitoring Mode Covert Camera SettingsEvent Monitoring Then the DVR displays Viewing Images from Covert Cameras Spot MonitoringSelecting the Camera to Display on a Spot Monitor Sequence Menu PTZ Mode Entering the PTZ ModeControlling the PTZ Cameras Saving Camera Position Settings as Presets Positioning the PTZ Cameras Using the Front Panel Buttons Using a Mouse for Convenient PTZ Control Loading a PresetPTZ Toolbar PTZ Toolbar Tools Icons Action Exiting the PTZ Mode Recording VideoPanic Recording Recording Audio Playing Recorded Video Cameo Playback Button Functions ButtonFunction Searching Video Using the Mouse for PlaybackPlayback Button Functions Button Function Search Menu Options Search MenuOption Function Go to the First Go to the Last Calendar Search Go to the Date/Time Event Log Search 14 Event Log Search Screen Narrowing Your Event Search Using Option Alarm-In Event Log Search Options Action FromMotion Self-Diagnostic Events Text-In SearchEvent Log Search Options OptionAction Video Loss 16 Text-In Search Screen Narrowing Your Text-In Search Using Option Channel 11 Text-In Search Options Action FromText Input Device Name Text-In Search Options Action Comp Motion SearchValue Line Motion Search Options Option Action FromZone 12 Motion Search Options Option Action Sensitivity Copying Video Clips Using the Clip-Copy Screen 14 Clip Copy Options Action From PasswordDest File name Naming a Video Clip File Using the DVR While Backing Up Video Operation Preparing the USB-IDE hard disk drive in Windows USB Hard Disk Drive Preparation Fdisk Option menu, choose 5. Change current fixed disk drive Query Example Text-In Query Examples Figure B-2 Query example Figure C-1 ClipPlayer Screen Reviewing Video Clips Option ClipPlayer Function Select from Save , Print , Info , Image Processing , Video Reviewing Video Clips 140 Figure D-1 Time Overlap Time Overlap Time Overlap 142 Problem Possible Solution Troubleshooting Troubleshooting 144 Master Unit Slave Unit Connector Pinouts Connector Pinouts 146 Map of Screens Map of Screens 148 System Log Notices System Log Notices 150 Error Code Notices System Upgrade RelatedNumber Description Clip Copy Related Specifications Video specificationsInputs/Outputs Connectors StorageGeneral Index Page Loading a PTZ preset 114 positioning PTZ cameras Page Page +1.800.796.CCTV North America only HVSsupport@honeywell.com