Specifications

￿￿￿￿￿&TKXG￿2QYGTTable 4￿&KUUKRCVKQP-5lists the drive power dissipation and the corresponding currents for the various modes of operation of the Maxtor Atlas 10K III hard disk drive.

Power Dissipation in Various Modes (Low-Profile Drives)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table

 

4-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12'4#6+10/1&'Startup￿1(￿

 

 

￿￿￿&+5

 

 

 

￿￿￿￿￿)￿￿￿&+50.9 -$

 

￿￿￿&+5￿￿￿￿￿)6;2+%#30.9-$￿.9#665￿￿￿￿￿)￿￿￿&+5#8)30.￿￿-$219'4￿￿￿￿￿￿)￿￿￿&+530.9-$

 

￿￿￿&+5￿￿￿￿￿). -$￿#/24/56;2+%#.￿)￿8-$￿70.￿￿￿￿￿)￿￿￿&+5#8'4#)'.2.2-5$￿16*'49+5'￿￿￿￿￿)￿￿￿&+5%744'06.-$￿￿￿016'&1,&+54.8￿)9-$￿

 

 

peak

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Idle

0.63

0.63

0.63

.46

.46

0.46

10.

10.

10.2

 

 

Random Seek

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Read/

0.97

0.97

0.97

.79

.79

0.79

15.

15.

15.6

 

 

Write3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

100%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Random Seek

1.14

1.14

1.14

.52

.52

0.52

16.3

16.3

16.3

 

 

(No R/W)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standby

0.48

0.48

0.48

.305

.305

.305

7.26

7.26

7.26

 

1. Current is RMS except for Startup. Startup current is the peak (> 10 ms) current required during spindle startup. Current measurements do not include power required for SCSI termination.

2. Idle mode is in effect when the drive is not reading, writing, seeking, or executing any commands. A portion of the R/W circuitry is powered down, the motor is up to speed and the Drive Ready condition exists.The actuator resides on the last track accessed.

3. Random Seek + Read/Write measured at 100% random 2KB R/W, Q=4.

4. Maximum Average Current is defined as mean current plus 3 Standard Deviations.

5. Power requirements reflect nominal values for +12V and +5V power supplies.

6. Standby mode is in effect when the motor is stopped, the actuator parked, and all electronics except the interface control is in low power state. Standby will occur after a programmable time-out since last host access occurs. Drive Ready and Seek Complete status exist. The Standby mode will not be in effect upon receipt of a command which requires disk access or upon receipt of a spin-up command.

4-6 Maxtor Atlas 10K III

Page 58
Image 58
Maxtor 10K III manual +50.9 -$, Power Dissipation in Various Modes Low-Profile Drives