SCSI Description

￿￿￿￿￿￿￿￿(14/#6The FORMAT￿70+6￿&GHGEVUNIT￿.KUVDefect￿*GCFGTList￿Header (Table 5-15)provides several optional format control bits to give the initiator more control over the defect lists. Table 5-16provides descriptions of the data fields in the Defect List Header

.FORMAT UNIT Defect List Header-Data Format

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reserved

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FOV

DPRY

DCRT

STPF

 

IP

DSP

Immed

VS

 

 

 

 

 

 

 

 

 

2-3

 

 

 

Defect List Length

 

 

 

 

 

 

 

 

 

 

 

 

 

$[VG$KV

 

FORMAT UNIT Defect￿List Header￿-Field Descriptions￿

￿

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table

5-16

 

 

 

 

0COGFOV

 

 

The Format Options Valid bit indicates&GUETKRVKQPthat the remaining option bits in this byte

 

 

 

are valid. If this bit is not set, the remaining bits, except Immed, are ignored.

 

 

 

during the format to identify defective areas on the media. The drive's default

DPRY

 

 

is 0, indicating that the drive should replace sectors found in the Primary Defect

 

 

 

List during the format.

 

 

 

 

 

 

The Disable Certification bit specifies whether the drive should certify the media

DCRT

 

 

during the format. The drive’s default is 0, indicating that the drive should certify

 

 

 

the media.

 

 

 

 

 

 

The Stop Format bit specifies the error conditions under which the drive is to

STPF

 

Tableterminate5-15

the format. The state of the bit is ignored and the drive acts as if this

 

 

bit is set. If either the Grown Defect List or the Primary Defect List is not found,

 

 

 

the format operation terminates with a CHECK CONDITION status and a sense

 

 

 

key of MEDIUM ERROR

 

 

 

 

 

 

 

 

 

 

 

The Initialization Pattern bit signals the drive that the FORMAT UNIT Parameter

 

 

 

List contains initialization pattern information.

 

 

 

 

 

 

An Initialization Pattern bit of 1 indicates that an initialization pattern descriptor

IP

 

 

(Table 5-17)is included in the FORMAT UNIT parameter list immediately follow-

 

 

ing the Defect List Header.

 

 

 

 

 

 

 

 

 

 

 

 

An Initialization Pattern bit of 0 indicates that an initialization pattern descriptor

 

 

 

(Table 5-17)is not included in the FORMAT UNIT parameter list, and the drive

 

 

 

will use its default initialization pattern of all zeros.

 

 

 

 

 

 

 

 

 

 

 

TheDisableSavingParameterprohibitsthedrivefrompreservingMODESELECT

DSP

 

 

parameters received while the Format is in progress. This bit is ignored, and the

 

 

 

drive acts as if it were set.

 

 

 

 

 

 

 

 

 

 

 

When the Immediate bit is 0, the drive returns a status after the format operation

 

 

 

completes. If the disconnect privilege is granted in the accompanying IDENTIFY

 

 

 

message, the drive disconnects from the bus after fetching and validating the

 

 

 

Command Descriptor Block and the FORMAT UNIT Parameter List. If the discon-

 

 

 

nect privilege is not granted, the drive stays connected to the bus during the

Immed

 

 

entire FORMAT UNIT command. When the Immediate bit is set to 1, the drive

 

 

returns a status after the Command Descriptor Block and FORMAT UNIT Param-

 

 

 

 

 

 

eter List have been fetched and validated. In this case, the drive ignores the

 

 

 

IDENTIFY message's disconnect privilege bit and remains connected to the bus

 

 

 

while it validates the Command Descriptor Block and Parameter List. It returns

 

 

 

the completion status before it disconnects. The drive then proceeds with the

 

 

 

format.

 

 

 

 

 

 

 

 

 

 

 

VS

 

 

Vendor-specific. Must be 0.

 

 

 

 

 

 

 

 

 

 

 

that follow. A value of 0 is valid and means that no Defect Descriptors follow.

Defect List Length

A CHECK CONDITION status is returned if this value is not a multiple of the de-

fect descriptor size. The Defect List Length is equal to four times the number of

 

 

 

 

 

 

defect descriptors if Block format is used, or eight times if Bytes From Index for-

 

 

 

mat or Physical Sector format is used.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maxtor Atlas 10K III

5-17

Page 81
Image 81
Maxtor 10K III manual Format Unit Defect List Header-Data Format, FOV Dpry Dcrt Stpf DSP, Immed Defect List Length