Storm Control Configuration, Status | Planet Technology SGSW-24040R

User’s Manual of WGSW-24040 / WGSW-24040R

SGSW-24040 / SGSW-24040R

4.8.7 Storm Control Configuration

Storm control for the switch is configured on this page. There three types of storm rate control:

Unicast storm rate control

Multicast storm rate control

Broadcast storm rate control.

The rate is 2^n, where n is equal to or less than 15, or "No Limit". The unit of the rate can be either pps (packets per second) or kpps (kilopackets per second). The configuration indicates the permitted packet rate for unicast, multicast, or broadcast traffic across the switch.

The Storm Control Configuration screen in Figure 4-8-14appears.

Figure 4-8-14Storm Control Configuration page screenshot

The page includes the following fields:


Object		Description
•	Frame Type	The settings in a particular row apply to the frame type listed here:
		•	unicast
		•	multicast
		•	broadcast.

•	Status	Enable or disable the storm control status for the given frame type.

•	Rate	The rate unit is packet per second (pps), configure the rate as 1, 2, 4, 8, 16, 32,
		64, 128, 256, 512, 1K, 2K, 4K, 8K, 16K, 32K, 64K, 128K, 256K, 512K, or 1024K.
		The 1 kpps is actually 1002.1 pps.

131

Image 131

Planet Technology SGSW-24040R, WGSW-24040R user manual Storm Control Configuration, Frame Type, Status, Rate

Contents

User’s Manual Weee Warning TrademarksDisclaimer FCC Warning CE Mark Warning Table of Conetnts 5.1 140 105118 132 187 159181 185 212 208 244 229237 265 251257 287 272277 282 297 290293 295 Product Description Packet Contents High Performance How to Use This Manual 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 Product FeaturesHigh-performance 5GbE Stacking interface ¾ Layer 2 Features ¾ Physical Port ¾ Stacking ¾ Multicast¾ Security ¾ Management Hardware Specification Product Specification Traffic classification based, Strict priority and WRR Gigabit SFP slots Switch Front PanelHardware Description Gigabit TP interface Master LED Reset buttonAbout 1~3 second Stack ID LED Indications Off To indicate that the SFP port is link down 1000Base-SX/LX SFP interfaces Shared Port-21~Port-24Speed 1000Mbps 5Rear panel of WGSW-24040 Switch Rear Panel Cascade UP AC Power ReceptacleStack ports 9SGSW-24040 / SGSW-24040R Stack Ports DC Power Connector Desktop Installation Install the Switch Rack Mounting Supply power to the Managed Switch 13Plug-in the SFP transceiver Installing the SFP transceiver „ Remove the transceiver module „ Approved Planet SFP Transceivers„ Connect the fiber cable Page Power switch in the OFF position and the DC power is OFF Connecting DC Power Supply WGSW-24040R / SGSW-24040R SGSW-24040 / SGSW-24040R Stack Installation Management Stacking Connecting Stacking cable Stack ID Master LED 21Separated Stack connection This chapter covers the following topics Requirements Method Advantages Disadvantages Management Access OverviewAdministration Console „ 115200 bps „ 8 data bits „ No parity „ 1 stop bit Direct Access Web Management 4Web main screen of Managed Switch Virtual Terminal Protocols SNMP-Based Network ManagementProtocols Management Architecture Snmp Protocol About Web-based Management WEB Configuration Http//192.168.0.100 „ Logging on the switchPage RJ-45 Ports SFP Ports Stack Ports Main WEBPanel Display State Main Menu 5WGSW/SGSW Managed Switch Main Funcrions Menu System IP Configuration System Information Page IP Configuration Password User AuthenticationOld Password New Password Sntp Configuration Click System Web Firmware Upgrade WEB Firmware Upgrade Tftp Server IP Tftp Firmware UpgradeUpgrade button Click System -TFTP Firmware Upgrade 8TFTP Firmware upgrade pop-up message „ Configuration Download Configuration Save „ Configuration Upload Configuration UploadPage Factory Default System Reboot 18Set Start-up screenshot „ Example 1 Save Current Configuration setting 19Download system software screenshot „ Example 2 Downloading System Software from a Server „ Example 3 Downloading Configuration Settings from a Server „ Example 4 Saving or Restoring Configuration Settings Snmp Operations Snmp System ConfigurationSimple Network Management Protocol Snmp Overview Write Community ModeVersion Read Community System Name Snmp System Information ConfigurationSnmp Trap Configuration System Contact Trap Destination Trap ModeTrap Version Trap Community Group Name SNMPv3 ConfigurationSNMPv3 Accesses Configuration Delete Read View Name SNMPv3 Communities ConfigurationSecurity Model Security Level Security Name SNMPv3 Groups Configuration Protocol SNMPv3 Users ConfigurationAuthentication User Name View Name SNMPv3 Views ConfigurationPrivacy Password Privacy Protocol OID Subtree „ Example Add a new SNMPv3 userView Type 9SNMPv3 Users-NEW page screenshot „ Example Add a new SNMPv3 Group 11SNMPv3 Groups-NEW page screenshot Port Management Port Configuration Flow Control Power ControlPort Link 2Port Statistics Overview page screenshot Port Statistics Overview Detailed Port Statistics Receive and Transmit Queue Counters Receive Error CountersReceive Total and Transmit Total Receive and Transmit Size Counters Tx Drops Port Mirroring ConfigurationTransmit Error Counters Port to mirror to Mirror Port Configuration 6Port Mirror Configuration page screenshot „ Sgsw Stackable Switch 1Link Aggregation Link AggregationPage Destination MAC Static Aggregation ConfigurationStatic Aggregation Group Configuration Hash Code Contributors Port Members LocalityGroup ID Role Lacp ConfigurationLacp Enabled Key Lacp Port Status Lacp System Status Partner Port Lacp Discarded Lacp statisticsLacp Transmitted Lacp Received Vlan Overview Vlan Ieee 802.1Q Standard Ieee 802.1Q Vlan 802.1Q Vlan Tags Port Vlan ID Vlan Classification VLANs Vlan Learning ObjectDescription Vlan ModeVlan Basic Information Supported VLANs Understand nomenclature of the Switch Vlan Port Configuration Pvid This is the logical port number for this row Port Vlan ID In-Q ModeLink Type Ether type Vlan ID Vlan Membership Configuration„ Adding Static Members to VLANs Vlan Index „ Isolated ports Private Vlan ConfigurationOverview „ Promiscuous ports Promiscuous Pvlan Port TypeIsolated Bridge Protocol Data Units Rapid Spanning Tree Protocol Port transitions from one state to another as follows Creating a Stable STP TopologySTP Port States Below ConfigurableExcept by setting priority STP Parameters STP Operation Levels Default Spanning-Tree Configuration Feature Default Value Maximum Age TimerForward Delay Timer Variable Description Default Value Port Priority Illustration of STP 110 Max Age Rstp System ConfigurationForward Delay System Priority Rstp Bridge Status Path Cost Rstp Port ConfigurationRstp Enabled Point2Point PriorityEdge Port Type Link Type Ieee 802.1w-2001 Ethernet Rstp Port Status TCN Rstp Port StatisticsRstp STP QoS Terminology Quality of ServiceUnderstand QOS Frame.The following QCE types are supported QoS Control List ConfigurationQCL # QCE Type Traffic Class QoS Control Entry ConfigurationType Value Port QoS Configuration User Priority Default ClassQueuing Mode Queue Weighted Application Rules QCL Configuration WizardSet up Policy Rules Port in a QCL member, click the radio button Includes the folling fileds Object DescriptionQCL ID Frames that hit this QCE are set to match this specific QCL Games Set up Typical Network Application RulesAudio and Video Select the QCL ID to which these QCEs apply User DefinitionButtons Set up ToS Precedence Mapping Set up Vlan Tag Priority Mapping QoS Statistics Bandwidth Control Rate Storm Control ConfigurationFrame Type Status About the Internet Group Management Protocol Igmp Snooping MulticastIgmp Snooping 133 0x12 Igmp Versions 10x17 „ Igmp Querier Idle Member Igmp Snooping Igmp Snooping ConfigurationFlooding enabled Enabled Igmp Querier Fast Leave Igmp Port Related ConfigurationRouter Port Vlan ID of the entry Igmp Snooping StatusObject Description Multicast Address Table Overview of MAC-Based Authentication Ieee 802.1X Network Access ControlOverview of 802.1X Port-Based Authentication „ Device Roles Understanding Ieee 802.1X Port-Based Authentication „ Authentication Initiation and Message Exchange „ Ports in Authorized and Unauthorized States 10-2EAP message exchange Radius Secret 10.2 802.1X System ConfigurationRadius IP Period ReauthenticationEnabled EAP Timeout 10.3 802.1X and MAC-Based Authentication Port Configuration Max Clients Port State Restart Last ID 10.4 802.1X Port StatusState Last Source 10-6802.1X Statistics Port 1 page screenshot 10.5 802.1X and MAC-Based Authentication Statistics Direction Name Ieee Name Description Eapol Counters Port- and MAC-based Radius Counters Direction Name Ieee NameDescription Port-based MAC-based MAC-based „ Last Supplicant/Client Info Windows Platform Radius Server Configuration 155 „ Configure Sample EAP-MD5 Authentication 10.7 802.1X Client Configuration 157 158 Ingress Port Access Control ListsAccess Control List Configuration Logging ActionRate Limiter Port Copy Switch ACE Configuration Dmac Filter „ MAC Parameters„ Vlan Parameters Smac Filter ARP/ Rarp „ ARP Parameters IP Protocol Filter „ IP ParametersIP/Ethernet Length Ethernet IP TTL „ TCP/UDP Parameters „ Icmp Parameters TCP ACK TCP FINTCP SYN TCP PSH EtherType Filter ACL Configuration wizard„ Ethernet Type Parameters 11-3Set up Policy Rules page screenshot Policy 5 for guest ports Internet access only Policy ID Set up Port Policies Ethernet Type Common ServersInstant Messaging MSN Messenger Google Talk Yahoo Messenger Snmp Traps NetBIOS Ping Request Ping ReplyOthers 173 Source IP Address Set up Source MAC and Source IP BindingBinding Enabled UDP DoS Fraggle Set up DoS Attack Detection Rules Icmp DoS Smurf Death Deny Switch nPort n Policy n 512K ACL Rate Limiter ConfigurationRate Limiter ID 16K 32K 64K 128K ACL Ports Configuration 180 Address Table MAC Address Table ConfigurationAging Configuration Range 10-10000000 seconds Default 300 seconds Static MAC Table Configuration MAC Table Columns MAC Address Table StatusDynamic MAC Table Navigating the MAC Table 184 Secure DisableMAC Table Learning Auto 186 Link Layer Discovery Protocol Lldp Tx Interval Lldp Configuration„ Lldp Parameters Tx Reinit „ 4.14.2.2 Lldp Port ConfigurationTx Delay Tx Hold Sys Capa Port DescrSys Name Sys Descr Lldp Neighbor „ Global Counters Lldp Statistics Local Counters Cable Status Cable DiagnosticsNetwork Diagnastics Ping Size PingDestination IP Address „ Ring topology „ Chain topology same as a disconnected ring Stacking SGSW-24040 / SGSW-24040R 197 „ Replacing a Switch Switch IDs„ Assigning and Swapping Switch IDs „ Removing a Switch From the Stack Stack Redundancy „ General Switch ID Assignment RulesMaster Election Utilize all stack links in the ring Shortest Path Forwarding Stack Configuration „ Stack List Master SwitchStack Information „ Stack Topology „ Master Forwarding Table 16-10Port State Overview page screenshot Stack Port State Ovewview Stack Example „ Identify the Master Switch 206 207 Logon to the Console Accessing the CLI „ Configure IP address Configure IP address Subnet Mask Gateway Switch/ ip setup 192.168.1.100 255.255.255.0 Telnet login Syntax System CommandCommand Groups System Configuration Example System RebootSystem Restore Default System Prompt Default SettingSystem Name System Sntp System Password System Firmware Load System Timezone 217 Parameters IP ConfigurationSyntax IP Ping IP Setup 220 Port State Port Management CommandPort Configuration Port Flow Control Port Mode Port Maximum Frame Port Excessive Port Power Port VeriPHY Port Statistics Port Numbers Mirror SID Mirror ConfigurationMirror Port Mirror Mode Parameters portlist Port list Link Aggregation CommandAggregation Configuration Aggregation Add Aggregation Lookup Aggregation Delete Aggregation Mode Lacp Configuration Lacp Key Lacp Mode Lacp Status Lacp Role Lacp Statistics 236 Vlan Mode Vlan Configuration CommandVlan Configuration Tagged Allow tagged frames only Vlan Frame TypeAll Vlan Link Type Vlan Ingress Filter Man Set out layer Vlan tag ether type MAN Vlan Q-in-Q ModeVlan Ethernet Type Vlan Delete Vlan Add Vlan Lookup Pvlan Isolate Pvlan Configuration Rstp SysPrio Spanning Tree Protocol CommandRstp Configuration Rstp Age Rstp Delay Rstp Version Rstp ModeNormal Rstp Default Setting Rstp Priority Rstp Cost Rstp P2P Rstp Edge Rstp Status Rstp mCheck Rstp Statistics Igmp Mode Multicast Configuration CommandIgmp Configuration Igmp State Igmp Fast Leave Igmp Querier Igmp Router Igmp Status Igmp FloodingIgmp Groups 256 QoS Classes Quality of Service CommandQoS Configuration QoS Default QoS QCL Port QoS Tag Priority Qceid Qclid QCL ID Default SettingQoS QCL Add Parameters Qclid QoS QCL Lookup QoS QCL Delete QoS Rate Limiter QoS ModeQoS Weight QoS Shaper QoS Multicast QoS Unicast QoS Broadcast Dotx1 Mode 802.1x Port Access Control CommandDot1x Configuration Dot1x Server Dot1x Status Dot1x Secret Dot1x Authenticate Dot1x Period Dot1x Re-authentication Dot1x Statistics Dot1x Timeout Parameters Portlist Dot1x ClientsDot1x Agetime Dot1x Holdtime ACL Action Access Control List CommandACL Configuration ACL Rate ACL Policy ACL Add ACL Delete ACL Lookup Mac Add MAC Address Table CommandMAC Configuration MAC Lookup MAC Delete MAC Learning MAC Age Time MAC Statistics MAC Dump MAC Flash Lldp Mode Lldp CommandLldp Configuration Lldp Interval Lldp Optional TLV Lldp Hold Lldp Delay Lldp Information Lldp Reinit Lldp Statistics Stack Master Reelect Stack Management CommandStack List Stack SID Delect Stack SelectStack SID Swap Stack SID Asign Store-and-Forward LearningForwarding & Filtering If attached device is 100Base-TX port will set to Auto-Negotiation 292 Switch does not power up Solution Link LED is not lit SolutionPerformance is bad Solution Why the Switch doesnt connect to the network Solution „ While IP Address be changed or forgotten admin password Stacking not functioning Solution 10/100Mbps, 10/100Base-TX Switchs RJ-45 Pin AssignmentsRJ-45 Connector pin assignment Contact = Brown Straight Cable= Brown Straight Cable ARP ACEACL Aggregation DoS DESDhcp DNS Http DscpEthernet Type FTP Imap IcmpIeee Igmp MAC Table IpmcLldp NFS NetBIOSMD5 Mirroring Private Vlan PingPolicer POP3 Samba QCLQoS Rarp Sntp SHASmtp Snmp ToS TCPTelnet Tftp UDP 308