Lldp Statistics, „ Global Counters | Planet Technology WGSW-24040R

User’s Manual of WGSW-24040 / WGSW-24040R

SGSW-24040 / SGSW-24040R

4.14.4 LLDP Statistics

This page provides an overview of all LLDP traffic. Two types of counters are shown. Global counters are counters that refer to the whole stack, switch, while local counters refers to counters for the currently selected switch. The LLDP Statistics screen in Figure 4-14-4appears.

Figure 4-14-4LLDP Statistics page screenshot

Global Counters

ObjectDescription

•Neighbor entries were Shows the time for when the last entry was last deleted or added. It is also shows

	last changed at	the time elapsed since last change was detected.

•	Total Neighbors	Shows the number of new entries added since switch reboot.
	Entries Added

•	Total Neighbors	Shows the number of new entries deleted since switch reboot.
	Entries Deleted

192

Image 192

Planet Technology WGSW-24040R, SGSW-24040R user manual Lldp Statistics, „ Global Counters

Contents

User’s Manual Trademarks DisclaimerFCC Warning CE Mark Warning Weee Warning Table of Conetnts 5.1 105 118132 140 159 181185 187 208 212 229 237244 251 257265 272 277282 287 290 293295 297 Packet Contents Product Description High Performance How to Use This Manual Product Features High-performance 5GbE Stacking interface ¾ Layer 2 Features¾ Physical Port 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 ¾ Multicast ¾ Security¾ Management ¾ Stacking Product Specification Hardware Specification Traffic classification based, Strict priority and WRR Switch Front Panel Hardware DescriptionGigabit TP interface Gigabit SFP slots Reset button About 1~3 secondStack ID Master LED LED Indications 1000Base-SX/LX SFP interfaces Shared Port-21~Port-24 Speed 1000MbpsOff To indicate that the SFP port is link down Switch Rear Panel 5Rear panel of WGSW-24040 AC Power Receptacle Stack portsCascade UP DC Power Connector 9SGSW-24040 / SGSW-24040R Stack Ports Install the Switch Desktop Installation Supply power to the Managed Switch Rack Mounting Installing the SFP transceiver 13Plug-in the SFP transceiver „ Approved Planet SFP Transceivers „ Connect the fiber cable„ Remove the transceiver module Page Connecting DC Power Supply WGSW-24040R / SGSW-24040R Power switch in the OFF position and the DC power is OFF Stack Installation SGSW-24040 / SGSW-24040R Connecting Stacking cable Management Stacking Stack ID Master LED 21Separated Stack connection Requirements This chapter covers the following topics Management Access Overview Administration ConsoleMethod Advantages Disadvantages Direct Access „ 115200 bps „ 8 data bits „ No parity „ 1 stop bit 4Web main screen of Managed Switch Web Management SNMP-Based Network Management ProtocolsVirtual Terminal Protocols Snmp Protocol Management Architecture WEB Configuration About Web-based Management „ Logging on the switch Http//192.168.0.100Page Main WEB Panel DisplayState RJ-45 Ports SFP Ports Stack Ports 5WGSW/SGSW Managed Switch Main Funcrions Menu Main Menu IP Configuration System System Information Page IP Configuration User Authentication Old PasswordNew Password Password Sntp Configuration WEB Firmware Upgrade Click System Web Firmware Upgrade Tftp Firmware Upgrade Upgrade buttonClick System -TFTP Firmware Upgrade Tftp Server IP 8TFTP Firmware upgrade pop-up message Configuration Save „ Configuration Download Configuration Upload „ Configuration UploadPage Factory Default System Reboot „ Example 1 Save Current Configuration setting 18Set Start-up screenshot „ Example 2 Downloading System Software from a Server 19Download system software screenshot „ Example 3 Downloading Configuration Settings from a Server „ Example 4 Saving or Restoring Configuration Settings Snmp System Configuration Simple Network Management ProtocolSnmp Overview Snmp Operations Mode VersionRead Community Write Community Snmp System Information Configuration Snmp Trap ConfigurationSystem Contact System Name Trap Mode Trap VersionTrap Community Trap Destination SNMPv3 Configuration SNMPv3 Accesses ConfigurationDelete Group Name SNMPv3 Communities Configuration Security ModelSecurity Level Read View Name SNMPv3 Groups Configuration Security Name SNMPv3 Users Configuration AuthenticationUser Name Protocol SNMPv3 Views Configuration Privacy PasswordPrivacy Protocol View Name „ Example Add a new SNMPv3 user View TypeOID Subtree „ Example Add a new SNMPv3 Group 9SNMPv3 Users-NEW page screenshot 11SNMPv3 Groups-NEW page screenshot Port Configuration Port Management Power Control PortLink Flow Control Port Statistics Overview 2Port Statistics Overview page screenshot Detailed Port Statistics Receive Error Counters Receive Total and Transmit TotalReceive and Transmit Size Counters Receive and Transmit Queue Counters Port Mirroring Configuration Transmit Error CountersTx Drops Mirror Port Configuration Port to mirror to „ Sgsw Stackable Switch 6Port Mirror Configuration page screenshot Link Aggregation 1Link AggregationPage Static Aggregation Configuration Static Aggregation Group ConfigurationHash Code Contributors Destination MAC Locality Group IDPort Members Lacp Configuration Lacp EnabledKey Role Lacp System Status Lacp Port Status Lacp Partner Port Lacp statistics Lacp TransmittedLacp Received Discarded Vlan Vlan Overview Ieee 802.1Q Vlan Ieee 802.1Q Standard 802.1Q Vlan Tags Port Vlan ID Vlan Classification ObjectDescription Vlan Mode Vlan Basic InformationSupported VLANs VLANs Vlan Learning Vlan Port Configuration Understand nomenclature of the Switch This is the logical port number for this row Pvid In-Q Mode Link TypeEther type Port Vlan ID Vlan Membership Configuration „ Adding Static Members to VLANs Vlan IndexVlan ID Private Vlan Configuration Overview„ Promiscuous ports „ Isolated ports Pvlan Port Type IsolatedPromiscuous Rapid Spanning Tree Protocol Bridge Protocol Data Units Creating a Stable STP Topology STP Port StatesPort transitions from one state to another as follows Configurable Except by setting prioritySTP Parameters STP Operation Levels Below Maximum Age Timer Forward Delay TimerVariable Description Default Value Port Priority Default Spanning-Tree Configuration Feature Default Value Illustration of STP 110 Rstp System Configuration Forward DelaySystem Priority Max Age Rstp Bridge Status Rstp Port Configuration Rstp EnabledPath Cost Priority EdgePoint2Point Port Type Link Type Ieee 802.1w-2001 Ethernet Rstp Port Status Rstp Port Statistics RstpSTP TCN Quality of Service Understand QOSQoS Terminology QoS Control List Configuration QCL #QCE Type Frame.The following QCE types are supported QoS Control Entry Configuration Type ValueTraffic Class Port QoS Configuration Default Class Queuing ModeQueue Weighted User Priority QCL Configuration Wizard Set up Policy RulesApplication Rules Includes the folling fileds Object Description QCL IDFrames that hit this QCE are set to match this specific QCL Port in a QCL member, click the radio button Set up Typical Network Application Rules Audio and VideoGames User Definition ButtonsSelect the QCL ID to which these QCEs apply Set up ToS Precedence Mapping Set up Vlan Tag Priority Mapping QoS Statistics Bandwidth Control Storm Control Configuration Frame TypeStatus Rate Multicast Igmp SnoopingAbout the Internet Group Management Protocol Igmp Snooping 133 Igmp Versions 1 0x170x12 Idle Member „ Igmp Querier Igmp Snooping Configuration Flooding enabledEnabled Igmp Querier Igmp Snooping Igmp Port Related Configuration Router PortFast Leave Igmp Snooping Status Object DescriptionVlan ID of the entry Multicast Address Table Ieee 802.1X Network Access Control Overview of 802.1X Port-Based AuthenticationOverview of MAC-Based Authentication Understanding Ieee 802.1X Port-Based Authentication „ Device Roles „ Authentication Initiation and Message Exchange 10-2EAP message exchange „ Ports in Authorized and Unauthorized States 10.2 802.1X System Configuration Radius IPRadius Secret Reauthentication EnabledEAP Timeout Period 10.3 802.1X and MAC-Based Authentication Port Configuration Port State Max Clients Restart 10.4 802.1X Port Status StateLast Source Last ID 10.5 802.1X and MAC-Based Authentication Statistics 10-6802.1X Statistics Port 1 page screenshot Eapol Counters Direction Name Ieee Name Description Radius Counters Direction Name Ieee Name Description Port-basedMAC-based Port- and MAC-based „ Last Supplicant/Client Info MAC-based Windows Platform Radius Server Configuration 155 10.7 802.1X Client Configuration „ Configure Sample EAP-MD5 Authentication 157 158 Access Control Lists Access Control List ConfigurationIngress Port Action Rate LimiterPort Copy Logging ACE Configuration Switch „ MAC Parameters „ Vlan ParametersSmac Filter Dmac Filter „ ARP Parameters ARP/ Rarp „ IP Parameters IP/Ethernet LengthEthernet IP Protocol Filter IP TTL „ Icmp Parameters „ TCP/UDP Parameters TCP FIN TCP SYNTCP PSH TCP ACK ACL Configuration wizard „ Ethernet Type ParametersEtherType Filter Policy 5 for guest ports Internet access only 11-3Set up Policy Rules page screenshot Set up Port Policies Policy ID Common Servers Instant MessagingMSN Messenger Google Talk Yahoo Messenger Ethernet Type NetBIOS Ping Request Ping Reply OthersSnmp Traps 173 Set up Source MAC and Source IP Binding Binding EnabledSource IP Address Set up DoS Attack Detection Rules UDP DoS Fraggle Death Icmp DoS Smurf Switch n Port nPolicy n Deny ACL Rate Limiter Configuration Rate Limiter ID16K 32K 64K 128K 512K ACL Ports Configuration 180 MAC Address Table Configuration Aging ConfigurationRange 10-10000000 seconds Default 300 seconds Address Table Static MAC Table Configuration MAC Address Table Status Dynamic MAC TableNavigating the MAC Table MAC Table Columns 184 Disable MAC Table LearningAuto Secure 186 Lldp Link Layer Discovery Protocol Lldp Configuration „ Lldp ParametersTx Interval „ 4.14.2.2 Lldp Port Configuration Tx DelayTx Hold Tx Reinit Port Descr Sys NameSys Descr Sys Capa Lldp Neighbor Lldp Statistics „ Global Counters Local Counters Cable Diagnostics Network DiagnasticsCable Status Ping Destination IP AddressPing Size Stacking SGSW-24040 / SGSW-24040R „ Ring topology „ Chain topology same as a disconnected ring 197 Switch IDs „ Assigning and Swapping Switch IDs„ Removing a Switch From the Stack „ Replacing a Switch „ General Switch ID Assignment Rules Master ElectionStack Redundancy Shortest Path Forwarding Utilize all stack links in the ring Stack Configuration Master Switch Stack Information„ Stack Topology „ Stack List „ Master Forwarding Table Stack Port State Ovewview 16-10Port State Overview page screenshot „ Identify the Master Switch Stack Example 206 207 Accessing the CLI Logon to the Console Configure IP address „ Configure IP address Switch/ ip setup 192.168.1.100 255.255.255.0 Subnet Mask Gateway Telnet login System Command Command GroupsSystem Configuration Syntax System Reboot System Restore DefaultExample Default Setting System NameSystem Prompt System Password System Sntp System Timezone System Firmware Load 217 IP Configuration SyntaxParameters IP Setup IP Ping 220 Port Management Command Port ConfigurationPort State Port Mode Port Flow Control Port Maximum Frame Port Power Port Excessive Port Statistics Port VeriPHY Port Numbers Mirror Configuration Mirror PortMirror SID Mirror Mode Link Aggregation Command Aggregation ConfigurationAggregation Add Parameters portlist Port list Aggregation Delete Aggregation Lookup Aggregation Mode Lacp Configuration Lacp Mode Lacp Key Lacp Role Lacp Status Lacp Statistics 236 Vlan Configuration Command Vlan ConfigurationVlan Mode Vlan Frame Type AllTagged Allow tagged frames only Vlan Ingress Filter Vlan Link Type Vlan Q-in-Q Mode Vlan Ethernet TypeMan Set out layer Vlan tag ether type MAN Vlan Add Vlan Delete Vlan Lookup Pvlan Configuration Pvlan Isolate Spanning Tree Protocol Command Rstp ConfigurationRstp SysPrio Rstp Delay Rstp Age Rstp Mode Normal Rstp Default SettingRstp Version Rstp Cost Rstp Priority Rstp Edge Rstp P2P Rstp Status Rstp Statistics Rstp mCheck Multicast Configuration Command Igmp ConfigurationIgmp Mode Igmp State Igmp Querier Igmp Fast Leave Igmp Router Igmp Flooding Igmp GroupsIgmp Status 256 Quality of Service Command QoS ConfigurationQoS Default QoS Classes QoS Tag Priority QoS QCL Port Qclid QCL ID Default Setting QoS QCL AddParameters Qclid Qceid QoS QCL Delete QoS QCL Lookup QoS Mode QoS WeightQoS Rate Limiter QoS Shaper QoS Unicast QoS Multicast QoS Broadcast 802.1x Port Access Control Command Dot1x ConfigurationDotx1 Mode Dot1x Status Dot1x Server Dot1x Authenticate Dot1x Secret Dot1x Re-authentication Dot1x Period Dot1x Timeout Dot1x Statistics Dot1x Clients Dot1x AgetimeParameters Portlist Dot1x Holdtime Access Control List Command ACL ConfigurationACL Action ACL Policy ACL Rate ACL Add ACL Delete ACL Lookup MAC Address Table Command MAC ConfigurationMac Add MAC Delete MAC Lookup MAC Age Time MAC Learning MAC Dump MAC Statistics MAC Flash Lldp Command Lldp ConfigurationLldp Mode Lldp Optional TLV Lldp Interval Lldp Delay Lldp Hold Lldp Reinit Lldp Information Lldp Statistics Stack Management Command Stack ListStack Master Reelect Stack Select Stack SID SwapStack SID Delect Stack SID Asign Learning Forwarding & FilteringStore-and-Forward Auto-Negotiation If attached device is 100Base-TX port will set to 292 Link LED is not lit Solution Performance is bad SolutionWhy the Switch doesnt connect to the network Solution Switch does not power up Solution Stacking not functioning Solution „ While IP Address be changed or forgotten admin password Switchs RJ-45 Pin Assignments RJ-45 Connector pin assignment Contact10/100Mbps, 10/100Base-TX Straight Cable = Brown Straight Cable= Brown ACE ACLAggregation ARP DES DhcpDNS DoS Dscp Ethernet TypeFTP Http Icmp IeeeIgmp Imap Ipmc LldpMAC Table NetBIOS MD5Mirroring NFS Ping PolicerPOP3 Private Vlan QCL QoSRarp Samba SHA SmtpSnmp Sntp TCP TelnetTftp ToS UDP 308