Configure IP address | Planet Technology SGSW-24040R, WGSW-24040R

User’s Manual of WGSW-24040 / WGSW-24040R

SGSW-24040 / SGSW-24040R

1.For security reason, please change and memorize the new password after this first setup.

2.Only accept command in lowercase letter under console interface.

Configure IP address

The WGSW / SGSW Managed Switch is shipped with default IP address as following.

IP Address : 192.168.0.100

Subnet Mask : 255.255.255.0

To check the current IP address or modify a new IP address for the Switch, please use the procedures as follow:

Show the current IP address

1.On ”Switch/> ” prompt, enter “show ip”.

2.The screen displays the current IP address, Subnet Mask and Gateway. As show in Figure 5-2.

Figure 5-2Show IP information screen

Configure IP address

3.On “Switch/> ” prompt, enter the following command and press <Enter>. As show in Figure 5-3.

209

Image 209

Planet Technology SGSW-24040R, WGSW-24040R user manual „ Configure IP address

Contents

User’s Manual Disclaimer TrademarksFCC Warning CE Mark Warning Weee Warning Table of Conetnts 5.1 118 105132 140 181 159185 187 212 208 244 229237 265 251257 277 272282 287 293 290295 297 Product Description Packet Contents High Performance How to Use This Manual High-performance 5GbE Stacking interface ¾ Layer 2 Features Product Features¾ Physical Port 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 ¾ Security ¾ Multicast¾ Management ¾ Stacking Hardware Specification Product Specification Traffic classification based, Strict priority and WRR Hardware Description Switch Front PanelGigabit TP interface Gigabit SFP slots About 1~3 second Reset buttonStack ID Master LED LED Indications Off To indicate that the SFP port is link down 1000Base-SX/LX SFP interfaces Shared Port-21~Port-24Speed 1000Mbps 5Rear panel of WGSW-24040 Switch Rear Panel Cascade UP AC Power ReceptacleStack ports 9SGSW-24040 / SGSW-24040R Stack Ports DC Power Connector Desktop Installation Install the Switch Rack Mounting Supply power to the Managed Switch 13Plug-in the SFP transceiver Installing the SFP transceiver „ Remove the transceiver module „ Approved Planet SFP Transceivers„ Connect the fiber cable Page Power switch in the OFF position and the DC power is OFF Connecting DC Power Supply WGSW-24040R / SGSW-24040R SGSW-24040 / SGSW-24040R Stack Installation Management Stacking Connecting Stacking cable Stack ID Master LED 21Separated Stack connection This chapter covers the following topics Requirements Method Advantages Disadvantages Management Access OverviewAdministration Console „ 115200 bps „ 8 data bits „ No parity „ 1 stop bit Direct Access Web Management 4Web main screen of Managed Switch Virtual Terminal Protocols SNMP-Based Network ManagementProtocols Management Architecture Snmp Protocol About Web-based Management WEB Configuration Http//192.168.0.100 „ Logging on the switchPage Panel Display Main WEBState RJ-45 Ports SFP Ports Stack Ports Main Menu 5WGSW/SGSW Managed Switch Main Funcrions Menu System IP Configuration System Information Page IP Configuration Old Password User AuthenticationNew Password Password Sntp Configuration Click System Web Firmware Upgrade WEB Firmware Upgrade Upgrade button Tftp Firmware UpgradeClick System -TFTP Firmware Upgrade Tftp Server IP 8TFTP Firmware upgrade pop-up message „ Configuration Download Configuration Save „ Configuration Upload Configuration UploadPage Factory Default System Reboot 18Set Start-up screenshot „ Example 1 Save Current Configuration setting 19Download system software screenshot „ Example 2 Downloading System Software from a Server „ Example 3 Downloading Configuration Settings from a Server „ Example 4 Saving or Restoring Configuration Settings Simple Network Management Protocol Snmp System ConfigurationSnmp Overview Snmp Operations Version ModeRead Community Write Community Snmp Trap Configuration Snmp System Information ConfigurationSystem Contact System Name Trap Version Trap ModeTrap Community Trap Destination SNMPv3 Accesses Configuration SNMPv3 ConfigurationDelete Group Name Security Model SNMPv3 Communities ConfigurationSecurity Level Read View Name Security Name SNMPv3 Groups Configuration Authentication SNMPv3 Users ConfigurationUser Name Protocol Privacy Password SNMPv3 Views ConfigurationPrivacy Protocol View Name OID Subtree „ Example Add a new SNMPv3 userView Type 9SNMPv3 Users-NEW page screenshot „ Example Add a new SNMPv3 Group 11SNMPv3 Groups-NEW page screenshot Port Management Port Configuration Port Power ControlLink Flow Control 2Port Statistics Overview page screenshot Port Statistics Overview Detailed Port Statistics Receive Total and Transmit Total Receive Error CountersReceive and Transmit Size Counters Receive and Transmit Queue Counters Tx Drops Port Mirroring ConfigurationTransmit Error Counters Port to mirror to Mirror Port Configuration 6Port Mirror Configuration page screenshot „ Sgsw Stackable Switch 1Link Aggregation Link AggregationPage Static Aggregation Group Configuration Static Aggregation ConfigurationHash Code Contributors Destination MAC Port Members LocalityGroup ID Lacp Enabled Lacp ConfigurationKey Role Lacp Port Status Lacp System Status Partner Port Lacp Lacp Transmitted Lacp statisticsLacp Received Discarded Vlan Overview Vlan Ieee 802.1Q Standard Ieee 802.1Q Vlan 802.1Q Vlan Tags Port Vlan ID Vlan Classification Vlan Basic Information ObjectDescription Vlan ModeSupported VLANs VLANs Vlan Learning Understand nomenclature of the Switch Vlan Port Configuration Pvid This is the logical port number for this row Link Type In-Q ModeEther type Port Vlan ID Vlan ID Vlan Membership Configuration„ Adding Static Members to VLANs Vlan Index Overview Private Vlan Configuration„ Promiscuous ports „ Isolated ports Promiscuous Pvlan Port TypeIsolated Bridge Protocol Data Units Rapid Spanning Tree Protocol Port transitions from one state to another as follows Creating a Stable STP TopologySTP Port States Except by setting priority ConfigurableSTP Parameters STP Operation Levels Below Forward Delay Timer Maximum Age TimerVariable Description Default Value Port Priority Default Spanning-Tree Configuration Feature Default Value Illustration of STP 110 Forward Delay Rstp System ConfigurationSystem Priority Max Age Rstp Bridge Status Path Cost Rstp Port ConfigurationRstp Enabled Point2Point PriorityEdge Port Type Link Type Ieee 802.1w-2001 Ethernet Rstp Port Status Rstp Rstp Port StatisticsSTP TCN QoS Terminology Quality of ServiceUnderstand QOS QCL # QoS Control List ConfigurationQCE Type Frame.The following QCE types are supported Traffic Class QoS Control Entry ConfigurationType Value Port QoS Configuration Queuing Mode Default ClassQueue Weighted User Priority Application Rules QCL Configuration WizardSet up Policy Rules QCL ID Includes the folling fileds Object DescriptionFrames that hit this QCE are set to match this specific QCL Port in a QCL member, click the radio button Games Set up Typical Network Application RulesAudio and Video Select the QCL ID to which these QCEs apply User DefinitionButtons Set up ToS Precedence Mapping Set up Vlan Tag Priority Mapping QoS Statistics Bandwidth Control Frame Type Storm Control ConfigurationStatus Rate About the Internet Group Management Protocol Igmp Snooping MulticastIgmp Snooping 133 0x12 Igmp Versions 10x17 „ Igmp Querier Idle Member Flooding enabled Igmp Snooping ConfigurationEnabled Igmp Querier Igmp Snooping Fast Leave Igmp Port Related ConfigurationRouter Port Vlan ID of the entry Igmp Snooping StatusObject Description Multicast Address Table Overview of MAC-Based Authentication Ieee 802.1X Network Access ControlOverview of 802.1X Port-Based Authentication „ Device Roles Understanding Ieee 802.1X Port-Based Authentication „ Authentication Initiation and Message Exchange „ Ports in Authorized and Unauthorized States 10-2EAP message exchange Radius Secret 10.2 802.1X System ConfigurationRadius IP Enabled ReauthenticationEAP Timeout Period 10.3 802.1X and MAC-Based Authentication Port Configuration Max Clients Port State Restart State 10.4 802.1X Port StatusLast Source Last ID 10-6802.1X Statistics Port 1 page screenshot 10.5 802.1X and MAC-Based Authentication Statistics Direction Name Ieee Name Description Eapol Counters Description Port-based Radius Counters Direction Name Ieee NameMAC-based Port- and MAC-based MAC-based „ Last Supplicant/Client Info Windows Platform Radius Server Configuration 155 „ Configure Sample EAP-MD5 Authentication 10.7 802.1X Client Configuration 157 158 Ingress Port Access Control ListsAccess Control List Configuration Rate Limiter ActionPort Copy Logging Switch ACE Configuration „ Vlan Parameters „ MAC ParametersSmac Filter Dmac Filter ARP/ Rarp „ ARP Parameters IP/Ethernet Length „ IP ParametersEthernet IP Protocol Filter IP TTL „ TCP/UDP Parameters „ Icmp Parameters TCP SYN TCP FINTCP PSH TCP ACK EtherType Filter ACL Configuration wizard„ Ethernet Type Parameters 11-3Set up Policy Rules page screenshot Policy 5 for guest ports Internet access only Policy ID Set up Port Policies Instant Messaging Common ServersMSN Messenger Google Talk Yahoo Messenger Ethernet Type Snmp Traps NetBIOS Ping Request Ping ReplyOthers 173 Source IP Address Set up Source MAC and Source IP BindingBinding Enabled UDP DoS Fraggle Set up DoS Attack Detection Rules Icmp DoS Smurf Death Port n Switch nPolicy n Deny Rate Limiter ID ACL Rate Limiter Configuration16K 32K 64K 128K 512K ACL Ports Configuration 180 Aging Configuration MAC Address Table ConfigurationRange 10-10000000 seconds Default 300 seconds Address Table Static MAC Table Configuration Dynamic MAC Table MAC Address Table StatusNavigating the MAC Table MAC Table Columns 184 MAC Table Learning DisableAuto Secure 186 Link Layer Discovery Protocol Lldp Tx Interval Lldp Configuration„ Lldp Parameters Tx Delay „ 4.14.2.2 Lldp Port ConfigurationTx Hold Tx Reinit Sys Name Port DescrSys Descr Sys Capa Lldp Neighbor „ Global Counters Lldp Statistics Local Counters Cable Status Cable DiagnosticsNetwork Diagnastics Ping Size PingDestination IP Address „ Ring topology „ Chain topology same as a disconnected ring Stacking SGSW-24040 / SGSW-24040R 197 „ Assigning and Swapping Switch IDs Switch IDs„ Removing a Switch From the Stack „ Replacing a Switch Stack Redundancy „ General Switch ID Assignment RulesMaster Election Utilize all stack links in the ring Shortest Path Forwarding Stack Configuration Stack Information Master Switch„ Stack Topology „ Stack List „ Master Forwarding Table 16-10Port State Overview page screenshot Stack Port State Ovewview Stack Example „ Identify the Master Switch 206 207 Logon to the Console Accessing the CLI „ Configure IP address Configure IP address Subnet Mask Gateway Switch/ ip setup 192.168.1.100 255.255.255.0 Telnet login Command Groups System CommandSystem Configuration Syntax Example System RebootSystem Restore Default System Prompt Default SettingSystem Name System Sntp System Password System Firmware Load System Timezone 217 Parameters IP ConfigurationSyntax IP Ping IP Setup 220 Port State Port Management CommandPort Configuration Port Flow Control Port Mode Port Maximum Frame Port Excessive Port Power Port VeriPHY Port Statistics Port Numbers Mirror SID Mirror ConfigurationMirror Port Mirror Mode Aggregation Configuration Link Aggregation CommandAggregation Add Parameters portlist Port list Aggregation Lookup Aggregation Delete Aggregation Mode Lacp Configuration Lacp Key Lacp Mode Lacp Status Lacp Role Lacp Statistics 236 Vlan Mode Vlan Configuration CommandVlan Configuration Tagged Allow tagged frames only Vlan Frame TypeAll Vlan Link Type Vlan Ingress Filter Man Set out layer Vlan tag ether type MAN Vlan Q-in-Q ModeVlan Ethernet Type Vlan Delete Vlan Add Vlan Lookup Pvlan Isolate Pvlan Configuration Rstp SysPrio Spanning Tree Protocol CommandRstp Configuration Rstp Age Rstp Delay Rstp Version Rstp ModeNormal Rstp Default Setting Rstp Priority Rstp Cost Rstp P2P Rstp Edge Rstp Status Rstp mCheck Rstp Statistics Igmp Mode Multicast Configuration CommandIgmp Configuration Igmp State Igmp Fast Leave Igmp Querier Igmp Router Igmp Status Igmp FloodingIgmp Groups 256 QoS Configuration Quality of Service CommandQoS Default QoS Classes QoS QCL Port QoS Tag Priority QoS QCL Add Qclid QCL ID Default SettingParameters Qclid Qceid QoS QCL Lookup QoS QCL Delete QoS Rate Limiter QoS ModeQoS Weight QoS Shaper QoS Multicast QoS Unicast QoS Broadcast Dotx1 Mode 802.1x Port Access Control CommandDot1x Configuration Dot1x Server Dot1x Status Dot1x Secret Dot1x Authenticate Dot1x Period Dot1x Re-authentication Dot1x Statistics Dot1x Timeout Parameters Portlist Dot1x ClientsDot1x Agetime Dot1x Holdtime ACL Action Access Control List CommandACL Configuration ACL Rate ACL Policy ACL Add ACL Delete ACL Lookup Mac Add MAC Address Table CommandMAC Configuration MAC Lookup MAC Delete MAC Learning MAC Age Time MAC Statistics MAC Dump MAC Flash Lldp Mode Lldp CommandLldp Configuration Lldp Interval Lldp Optional TLV Lldp Hold Lldp Delay Lldp Information Lldp Reinit Lldp Statistics Stack Master Reelect Stack Management CommandStack List Stack SID Delect Stack SelectStack SID Swap Stack SID Asign Store-and-Forward LearningForwarding & Filtering If attached device is 100Base-TX port will set to Auto-Negotiation 292 Performance is bad Solution Link LED is not lit SolutionWhy the Switch doesnt connect to the network Solution Switch does not power up Solution „ While IP Address be changed or forgotten admin password Stacking not functioning Solution 10/100Mbps, 10/100Base-TX Switchs RJ-45 Pin AssignmentsRJ-45 Connector pin assignment Contact = Brown Straight Cable= Brown Straight Cable ACL ACEAggregation ARP Dhcp DESDNS DoS Ethernet Type DscpFTP Http Ieee IcmpIgmp Imap MAC Table IpmcLldp MD5 NetBIOSMirroring NFS Policer PingPOP3 Private Vlan QoS QCLRarp Samba Smtp SHASnmp Sntp Telnet TCPTftp ToS UDP 308