Port, Link, Flow Control | Planet Technology WGSW-24040R specs

User’s Manual of WGSW-24040 / WGSW-24040R

SGSW-24040 / SGSW-24040R

The page includes the following fields:


Object		Description
•	Port	This is the logical port number for this row.

•	Link	The current link state is displayed graphically. Green indicates the link is up and
		red that it is down.

•Current Link Speed Provides the current link speed of the port.

•Configured Link Speed Select any available link speed for the given switch port. Draw the menu bar to select the mode.

•Auto Speed - Setup Auto negotiation.

•	10 half	- Force sets 10Mbps/Half-Duplex mode.
•	10 Full	- Force sets 10Mbps/Full-Duplex mode.

•100 half - Force sets 100Mbps/Half-Duplex mode.

•100 full - Force sets 100Mbps/Full-Duplex mode.

•1000 full - Force sets 10000Mbps/Full-Duplex mode.

•Disable - Shutdown the port manually.

•	Flow Control	When Auto Speed is selected for a port, this section indicates the flow control
		capability that is advertised to the link partner.
		When a fixed-speed setting is selected, that is what is used.
		• Current Rx column indicates whether pause frames on the port are
		obeyed.
		• Current Tx column indicates whether pause frames on the port are
		transmitted.
		The Rx and Tx settings are determined by the result of the last Auto-Negotiation.
		Check the configured column to use flow control.
		This setting is related to the setting for Configured Link Speed.

•	Maximum Frame	Enter the maximum frame size allowed for the switch port, including FCS. The
		allowed range is 1518 bytes to 9600 bytes.

•Excessive Collision Configure port transmit collision behavior.

Mode	• Discard: Discard frame after 16 collisions (default).
	• estart: Restart backoff algorithm after 16 collisions.

• Power Control	The Usage column shows the current percentage of the power consumption per
	port. The Configured column allows for changing the power savings mode
	parameters per port.
	• Disabled: All power savings mechanisms disabled.
	• ActiPHY: Link down power savings enabled.
	• Dynamic: Link up power savings enabled.

78

Image 78

Planet Technology WGSW-24040R, SGSW-24040R user manual Port, Link, Flow Control, Maximum Frame, Power Control

Contents

User’s Manual FCC Warning CE Mark Warning TrademarksDisclaimer Weee Warning Table of Conetnts 5.1 132 105118 140 185 159181 187 208 212 229 237244 251 257265 282 272277 287 295 290293 297 Packet Contents Product Description High Performance How to Use This Manual ¾ Physical Port Product FeaturesHigh-performance 5GbE Stacking interface ¾ Layer 2 Features 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 ¾ Management ¾ Multicast¾ Security ¾ Stacking Product Specification Hardware Specification Traffic classification based, Strict priority and WRR Gigabit TP interface Switch Front PanelHardware Description Gigabit SFP slots Stack ID Reset buttonAbout 1~3 second Master LED LED Indications 1000Base-SX/LX SFP interfaces Shared Port-21~Port-24 Speed 1000MbpsOff To indicate that the SFP port is link down Switch Rear Panel 5Rear panel of WGSW-24040 AC Power Receptacle Stack portsCascade UP DC Power Connector 9SGSW-24040 / SGSW-24040R Stack Ports Install the Switch Desktop Installation Supply power to the Managed Switch Rack Mounting Installing the SFP transceiver 13Plug-in the SFP transceiver „ Approved Planet SFP Transceivers „ Connect the fiber cable„ Remove the transceiver module Page Connecting DC Power Supply WGSW-24040R / SGSW-24040R Power switch in the OFF position and the DC power is OFF Stack Installation SGSW-24040 / SGSW-24040R Connecting Stacking cable Management Stacking Stack ID Master LED 21Separated Stack connection Requirements This chapter covers the following topics Management Access Overview Administration ConsoleMethod Advantages Disadvantages Direct Access „ 115200 bps „ 8 data bits „ No parity „ 1 stop bit 4Web main screen of Managed Switch Web Management SNMP-Based Network Management ProtocolsVirtual Terminal Protocols Snmp Protocol Management Architecture WEB Configuration About Web-based Management „ Logging on the switch Http//192.168.0.100Page State Main WEBPanel Display RJ-45 Ports SFP Ports Stack Ports 5WGSW/SGSW Managed Switch Main Funcrions Menu Main Menu IP Configuration System System Information Page IP Configuration New Password User AuthenticationOld Password Password Sntp Configuration WEB Firmware Upgrade Click System Web Firmware Upgrade Click System -TFTP Firmware Upgrade Tftp Firmware UpgradeUpgrade button Tftp Server IP 8TFTP Firmware upgrade pop-up message Configuration Save „ Configuration Download Configuration Upload „ Configuration UploadPage Factory Default System Reboot „ Example 1 Save Current Configuration setting 18Set Start-up screenshot „ Example 2 Downloading System Software from a Server 19Download system software screenshot „ Example 3 Downloading Configuration Settings from a Server „ Example 4 Saving or Restoring Configuration Settings Snmp Overview Snmp System ConfigurationSimple Network Management Protocol Snmp Operations Read Community ModeVersion Write Community System Contact Snmp System Information ConfigurationSnmp Trap Configuration System Name Trap Community Trap ModeTrap Version Trap Destination Delete SNMPv3 ConfigurationSNMPv3 Accesses Configuration Group Name Security Level SNMPv3 Communities ConfigurationSecurity Model Read View Name SNMPv3 Groups Configuration Security Name User Name SNMPv3 Users ConfigurationAuthentication Protocol Privacy Protocol SNMPv3 Views ConfigurationPrivacy Password View Name „ Example Add a new SNMPv3 user View TypeOID Subtree „ Example Add a new SNMPv3 Group 9SNMPv3 Users-NEW page screenshot 11SNMPv3 Groups-NEW page screenshot Port Configuration Port Management Link Power ControlPort Flow Control Port Statistics Overview 2Port Statistics Overview page screenshot Detailed Port Statistics Receive and Transmit Size Counters Receive Error CountersReceive Total and Transmit Total Receive and Transmit Queue Counters Port Mirroring Configuration Transmit Error CountersTx Drops Mirror Port Configuration Port to mirror to „ Sgsw Stackable Switch 6Port Mirror Configuration page screenshot Link Aggregation 1Link AggregationPage Hash Code Contributors Static Aggregation ConfigurationStatic Aggregation Group Configuration Destination MAC Locality Group IDPort Members Key Lacp ConfigurationLacp Enabled Role Lacp System Status Lacp Port Status Lacp Partner Port Lacp Received Lacp statisticsLacp Transmitted Discarded Vlan Vlan Overview Ieee 802.1Q Vlan Ieee 802.1Q Standard 802.1Q Vlan Tags Port Vlan ID Vlan Classification Supported VLANs ObjectDescription Vlan ModeVlan Basic Information VLANs Vlan Learning Vlan Port Configuration Understand nomenclature of the Switch This is the logical port number for this row Pvid Ether type In-Q ModeLink Type Port Vlan ID Vlan Membership Configuration „ Adding Static Members to VLANs Vlan IndexVlan ID „ Promiscuous ports Private Vlan ConfigurationOverview „ Isolated ports Pvlan Port Type IsolatedPromiscuous Rapid Spanning Tree Protocol Bridge Protocol Data Units Creating a Stable STP Topology STP Port StatesPort transitions from one state to another as follows STP Parameters STP Operation Levels ConfigurableExcept by setting priority Below Variable Description Default Value Port Priority Maximum Age TimerForward Delay Timer Default Spanning-Tree Configuration Feature Default Value Illustration of STP 110 System Priority Rstp System ConfigurationForward Delay Max Age Rstp Bridge Status Rstp Port Configuration Rstp EnabledPath Cost Priority EdgePoint2Point Port Type Link Type Ieee 802.1w-2001 Ethernet Rstp Port Status STP Rstp Port StatisticsRstp TCN Quality of Service Understand QOSQoS Terminology QCE Type QoS Control List ConfigurationQCL # Frame.The following QCE types are supported QoS Control Entry Configuration Type ValueTraffic Class Port QoS Configuration Queue Weighted Default ClassQueuing Mode User Priority QCL Configuration Wizard Set up Policy RulesApplication Rules Frames that hit this QCE are set to match this specific QCL Includes the folling fileds Object DescriptionQCL ID Port in a QCL member, click the radio button Set up Typical Network Application Rules Audio and VideoGames User Definition ButtonsSelect the QCL ID to which these QCEs apply Set up ToS Precedence Mapping Set up Vlan Tag Priority Mapping QoS Statistics Bandwidth Control Status Storm Control ConfigurationFrame Type Rate Multicast Igmp SnoopingAbout the Internet Group Management Protocol Igmp Snooping 133 Igmp Versions 1 0x170x12 Idle Member „ Igmp Querier Enabled Igmp Querier Igmp Snooping ConfigurationFlooding enabled Igmp Snooping Igmp Port Related Configuration Router PortFast Leave Igmp Snooping Status Object DescriptionVlan ID of the entry Multicast Address Table Ieee 802.1X Network Access Control Overview of 802.1X Port-Based AuthenticationOverview of MAC-Based Authentication Understanding Ieee 802.1X Port-Based Authentication „ Device Roles „ Authentication Initiation and Message Exchange 10-2EAP message exchange „ Ports in Authorized and Unauthorized States 10.2 802.1X System Configuration Radius IPRadius Secret EAP Timeout ReauthenticationEnabled Period 10.3 802.1X and MAC-Based Authentication Port Configuration Port State Max Clients Restart Last Source 10.4 802.1X Port StatusState Last ID 10.5 802.1X and MAC-Based Authentication Statistics 10-6802.1X Statistics Port 1 page screenshot Eapol Counters Direction Name Ieee Name Description MAC-based Radius Counters Direction Name Ieee NameDescription Port-based Port- and MAC-based „ Last Supplicant/Client Info MAC-based Windows Platform Radius Server Configuration 155 10.7 802.1X Client Configuration „ Configure Sample EAP-MD5 Authentication 157 158 Access Control Lists Access Control List ConfigurationIngress Port Port Copy ActionRate Limiter Logging ACE Configuration Switch Smac Filter „ MAC Parameters„ Vlan Parameters Dmac Filter „ ARP Parameters ARP/ Rarp Ethernet „ IP ParametersIP/Ethernet Length IP Protocol Filter IP TTL „ Icmp Parameters „ TCP/UDP Parameters TCP PSH TCP FINTCP SYN TCP ACK ACL Configuration wizard „ Ethernet Type ParametersEtherType Filter Policy 5 for guest ports Internet access only 11-3Set up Policy Rules page screenshot Set up Port Policies Policy ID MSN Messenger Google Talk Yahoo Messenger Common ServersInstant Messaging Ethernet Type NetBIOS Ping Request Ping Reply OthersSnmp Traps 173 Set up Source MAC and Source IP Binding Binding EnabledSource IP Address Set up DoS Attack Detection Rules UDP DoS Fraggle Death Icmp DoS Smurf Policy n Switch nPort n Deny 16K 32K 64K 128K ACL Rate Limiter ConfigurationRate Limiter ID 512K ACL Ports Configuration 180 Range 10-10000000 seconds Default 300 seconds MAC Address Table ConfigurationAging Configuration Address Table Static MAC Table Configuration Navigating the MAC Table MAC Address Table StatusDynamic MAC Table MAC Table Columns 184 Auto DisableMAC Table Learning Secure 186 Lldp Link Layer Discovery Protocol Lldp Configuration „ Lldp ParametersTx Interval Tx Hold „ 4.14.2.2 Lldp Port ConfigurationTx Delay Tx Reinit Sys Descr Port DescrSys Name Sys Capa Lldp Neighbor Lldp Statistics „ Global Counters Local Counters Cable Diagnostics Network DiagnasticsCable Status Ping Destination IP AddressPing Size Stacking SGSW-24040 / SGSW-24040R „ Ring topology „ Chain topology same as a disconnected ring 197 „ Removing a Switch From the Stack Switch IDs„ Assigning and Swapping Switch IDs „ Replacing a Switch „ General Switch ID Assignment Rules Master ElectionStack Redundancy Shortest Path Forwarding Utilize all stack links in the ring Stack Configuration „ Stack Topology Master SwitchStack Information „ Stack List „ Master Forwarding Table Stack Port State Ovewview 16-10Port State Overview page screenshot „ Identify the Master Switch Stack Example 206 207 Accessing the CLI Logon to the Console Configure IP address „ Configure IP address Switch/ ip setup 192.168.1.100 255.255.255.0 Subnet Mask Gateway Telnet login System Configuration System CommandCommand Groups Syntax System Reboot System Restore DefaultExample Default Setting System NameSystem Prompt System Password System Sntp System Timezone System Firmware Load 217 IP Configuration SyntaxParameters IP Setup IP Ping 220 Port Management Command Port ConfigurationPort State Port Mode Port Flow Control Port Maximum Frame Port Power Port Excessive Port Statistics Port VeriPHY Port Numbers Mirror Configuration Mirror PortMirror SID Mirror Mode Aggregation Add Link Aggregation CommandAggregation Configuration Parameters portlist Port list Aggregation Delete Aggregation Lookup Aggregation Mode Lacp Configuration Lacp Mode Lacp Key Lacp Role Lacp Status Lacp Statistics 236 Vlan Configuration Command Vlan ConfigurationVlan Mode Vlan Frame Type AllTagged Allow tagged frames only Vlan Ingress Filter Vlan Link Type Vlan Q-in-Q Mode Vlan Ethernet TypeMan Set out layer Vlan tag ether type MAN Vlan Add Vlan Delete Vlan Lookup Pvlan Configuration Pvlan Isolate Spanning Tree Protocol Command Rstp ConfigurationRstp SysPrio Rstp Delay Rstp Age Rstp Mode Normal Rstp Default SettingRstp Version Rstp Cost Rstp Priority Rstp Edge Rstp P2P Rstp Status Rstp Statistics Rstp mCheck Multicast Configuration Command Igmp ConfigurationIgmp Mode Igmp State Igmp Querier Igmp Fast Leave Igmp Router Igmp Flooding Igmp GroupsIgmp Status 256 QoS Default Quality of Service CommandQoS Configuration QoS Classes QoS Tag Priority QoS QCL Port Parameters Qclid Qclid QCL ID Default SettingQoS QCL Add Qceid QoS QCL Delete QoS QCL Lookup QoS Mode QoS WeightQoS Rate Limiter QoS Shaper QoS Unicast QoS Multicast QoS Broadcast 802.1x Port Access Control Command Dot1x ConfigurationDotx1 Mode Dot1x Status Dot1x Server Dot1x Authenticate Dot1x Secret Dot1x Re-authentication Dot1x Period Dot1x Timeout Dot1x Statistics Dot1x Clients Dot1x AgetimeParameters Portlist Dot1x Holdtime Access Control List Command ACL ConfigurationACL Action ACL Policy ACL Rate ACL Add ACL Delete ACL Lookup MAC Address Table Command MAC ConfigurationMac Add MAC Delete MAC Lookup MAC Age Time MAC Learning MAC Dump MAC Statistics MAC Flash Lldp Command Lldp ConfigurationLldp Mode Lldp Optional TLV Lldp Interval Lldp Delay Lldp Hold Lldp Reinit Lldp Information Lldp Statistics Stack Management Command Stack ListStack Master Reelect Stack Select Stack SID SwapStack SID Delect Stack SID Asign Learning Forwarding & FilteringStore-and-Forward Auto-Negotiation If attached device is 100Base-TX port will set to 292 Why the Switch doesnt connect to the network Solution Link LED is not lit SolutionPerformance is bad Solution Switch does not power up Solution Stacking not functioning Solution „ While IP Address be changed or forgotten admin password Switchs RJ-45 Pin Assignments RJ-45 Connector pin assignment Contact10/100Mbps, 10/100Base-TX Straight Cable = Brown Straight Cable= Brown Aggregation ACEACL ARP DNS DESDhcp DoS FTP DscpEthernet Type Http Igmp IcmpIeee Imap Ipmc LldpMAC Table Mirroring NetBIOSMD5 NFS POP3 PingPolicer Private Vlan Rarp QCLQoS Samba Snmp SHASmtp Sntp Tftp TCPTelnet ToS UDP 308