ACL Rate Limiter Configuration | Planet Technology WGSW-24040R

User’s Manual of WGSW-24040 / WGSW-24040R

SGSW-24040 / SGSW-24040R

4.11.4 ACL Rate Limiter Configuration

Configure the rate limiter for the ACL of the switch.

The ACL Rate Limiter Configuration screen in Figure 4-11-13appears.

Figure 4-11-13ACL Rate Limiter Configuration page screenshot

The page includes the following fields:


Object		Description
•	Rate Limiter ID	The rate limiter ID for the settings contained in the same row.

•	Rate	The rate unit is packet per second (pps), configure the rate as																										,				,		,			,		,		,
•	Rate																										1	,		2		,	4	,	8		,	16	,	32	,
			,		,		,		,		,		,		,		,		,		,		,		,				,							, or
		64	,	128	,	256	,	512	,	1K	,	2K	,	4K	,	8K	,	16K	,	32K	,	64K	,	128K	,	256K			,		512K					, or

1024K.

The 1 kpps is actually 1002.1 pps.

178

Image 178

Planet Technology WGSW-24040R, SGSW-24040R ACL Rate Limiter Configuration, Rate Limiter ID, 16K 32K 64K 128K, 512K, 1024K

Contents

User’s Manual FCC Warning CE Mark Warning TrademarksDisclaimer Weee Warning Table of Conetnts 5.1 132 105118 140 185 159181 187 208 212 237 229244 257 251265 282 272277 287 295 290293 297 Packet Contents Product Description High Performance How to Use This Manual ¾ Physical Port Product FeaturesHigh-performance 5GbE Stacking interface ¾ Layer 2 Features 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 ¾ Management ¾ Multicast¾ Security ¾ Stacking Product Specification Hardware Specification Traffic classification based, Strict priority and WRR Gigabit TP interface Switch Front PanelHardware Description Gigabit SFP slots Stack ID Reset buttonAbout 1~3 second Master LED LED Indications Speed 1000Mbps 1000Base-SX/LX SFP interfaces Shared Port-21~Port-24Off To indicate that the SFP port is link down Switch Rear Panel 5Rear panel of WGSW-24040 Stack ports AC Power ReceptacleCascade UP DC Power Connector 9SGSW-24040 / SGSW-24040R Stack Ports Install the Switch Desktop Installation Supply power to the Managed Switch Rack Mounting Installing the SFP transceiver 13Plug-in the SFP transceiver „ Connect the fiber cable „ Approved Planet SFP Transceivers„ Remove the transceiver module Page Connecting DC Power Supply WGSW-24040R / SGSW-24040R Power switch in the OFF position and the DC power is OFF Stack Installation SGSW-24040 / SGSW-24040R Connecting Stacking cable Management Stacking Stack ID Master LED 21Separated Stack connection Requirements This chapter covers the following topics Administration Console Management Access OverviewMethod Advantages Disadvantages Direct Access „ 115200 bps „ 8 data bits „ No parity „ 1 stop bit 4Web main screen of Managed Switch Web Management Protocols SNMP-Based Network ManagementVirtual Terminal Protocols Snmp Protocol Management Architecture WEB Configuration About Web-based Management „ Logging on the switch Http//192.168.0.100Page State Main WEBPanel Display RJ-45 Ports SFP Ports Stack Ports 5WGSW/SGSW Managed Switch Main Funcrions Menu Main Menu IP Configuration System System Information Page IP Configuration New Password User AuthenticationOld Password Password Sntp Configuration WEB Firmware Upgrade Click System Web Firmware Upgrade Click System -TFTP Firmware Upgrade Tftp Firmware UpgradeUpgrade button Tftp Server IP 8TFTP Firmware upgrade pop-up message Configuration Save „ Configuration Download Configuration Upload „ Configuration UploadPage Factory Default System Reboot „ Example 1 Save Current Configuration setting 18Set Start-up screenshot „ Example 2 Downloading System Software from a Server 19Download system software screenshot „ Example 3 Downloading Configuration Settings from a Server „ Example 4 Saving or Restoring Configuration Settings Snmp Overview Snmp System ConfigurationSimple Network Management Protocol Snmp Operations Read Community ModeVersion Write Community System Contact Snmp System Information ConfigurationSnmp Trap Configuration System Name Trap Community Trap ModeTrap Version Trap Destination Delete SNMPv3 ConfigurationSNMPv3 Accesses Configuration Group Name Security Level SNMPv3 Communities ConfigurationSecurity Model Read View Name SNMPv3 Groups Configuration Security Name User Name SNMPv3 Users ConfigurationAuthentication Protocol Privacy Protocol SNMPv3 Views ConfigurationPrivacy Password View Name View Type „ Example Add a new SNMPv3 userOID Subtree „ Example Add a new SNMPv3 Group 9SNMPv3 Users-NEW page screenshot 11SNMPv3 Groups-NEW page screenshot Port Configuration Port Management Link Power ControlPort Flow Control Port Statistics Overview 2Port Statistics Overview page screenshot Detailed Port Statistics Receive and Transmit Size Counters Receive Error CountersReceive Total and Transmit Total Receive and Transmit Queue Counters Transmit Error Counters Port Mirroring ConfigurationTx Drops Mirror Port Configuration Port to mirror to „ Sgsw Stackable Switch 6Port Mirror Configuration page screenshot Link Aggregation 1Link AggregationPage Hash Code Contributors Static Aggregation ConfigurationStatic Aggregation Group Configuration Destination MAC Group ID LocalityPort Members Key Lacp ConfigurationLacp Enabled Role Lacp System Status Lacp Port Status Lacp Partner Port Lacp Received Lacp statisticsLacp Transmitted Discarded Vlan Vlan Overview Ieee 802.1Q Vlan Ieee 802.1Q Standard 802.1Q Vlan Tags Port Vlan ID Vlan Classification Supported VLANs ObjectDescription Vlan ModeVlan Basic Information VLANs Vlan Learning Vlan Port Configuration Understand nomenclature of the Switch This is the logical port number for this row Pvid Ether type In-Q ModeLink Type Port Vlan ID „ Adding Static Members to VLANs Vlan Index Vlan Membership ConfigurationVlan ID „ Promiscuous ports Private Vlan ConfigurationOverview „ Isolated ports Isolated Pvlan Port TypePromiscuous Rapid Spanning Tree Protocol Bridge Protocol Data Units STP Port States Creating a Stable STP TopologyPort transitions from one state to another as follows STP Parameters STP Operation Levels ConfigurableExcept by setting priority Below Variable Description Default Value Port Priority Maximum Age TimerForward Delay Timer Default Spanning-Tree Configuration Feature Default Value Illustration of STP 110 System Priority Rstp System ConfigurationForward Delay Max Age Rstp Bridge Status Rstp Enabled Rstp Port ConfigurationPath Cost Edge PriorityPoint2Point Port Type Link Type Ieee 802.1w-2001 Ethernet Rstp Port Status STP Rstp Port StatisticsRstp TCN Understand QOS Quality of ServiceQoS Terminology QCE Type QoS Control List ConfigurationQCL # Frame.The following QCE types are supported Type Value QoS Control Entry ConfigurationTraffic Class Port QoS Configuration Queue Weighted Default ClassQueuing Mode User Priority Set up Policy Rules QCL Configuration WizardApplication Rules Frames that hit this QCE are set to match this specific QCL Includes the folling fileds Object DescriptionQCL ID Port in a QCL member, click the radio button Audio and Video Set up Typical Network Application RulesGames Buttons User DefinitionSelect the QCL ID to which these QCEs apply Set up ToS Precedence Mapping Set up Vlan Tag Priority Mapping QoS Statistics Bandwidth Control Status Storm Control ConfigurationFrame Type Rate Igmp Snooping MulticastAbout the Internet Group Management Protocol Igmp Snooping 133 0x17 Igmp Versions 10x12 Idle Member „ Igmp Querier Enabled Igmp Querier Igmp Snooping ConfigurationFlooding enabled Igmp Snooping Router Port Igmp Port Related ConfigurationFast Leave Object Description Igmp Snooping StatusVlan ID of the entry Multicast Address Table Overview of 802.1X Port-Based Authentication Ieee 802.1X Network Access ControlOverview of MAC-Based Authentication Understanding Ieee 802.1X Port-Based Authentication „ Device Roles „ Authentication Initiation and Message Exchange 10-2EAP message exchange „ Ports in Authorized and Unauthorized States Radius IP 10.2 802.1X System ConfigurationRadius Secret EAP Timeout ReauthenticationEnabled Period 10.3 802.1X and MAC-Based Authentication Port Configuration Port State Max Clients Restart Last Source 10.4 802.1X Port StatusState Last ID 10.5 802.1X and MAC-Based Authentication Statistics 10-6802.1X Statistics Port 1 page screenshot Eapol Counters Direction Name Ieee Name Description MAC-based Radius Counters Direction Name Ieee NameDescription Port-based Port- and MAC-based „ Last Supplicant/Client Info MAC-based Windows Platform Radius Server Configuration 155 10.7 802.1X Client Configuration „ Configure Sample EAP-MD5 Authentication 157 158 Access Control List Configuration Access Control ListsIngress Port Port Copy ActionRate Limiter Logging ACE Configuration Switch Smac Filter „ MAC Parameters„ Vlan Parameters Dmac Filter „ ARP Parameters ARP/ Rarp Ethernet „ IP ParametersIP/Ethernet Length IP Protocol Filter IP TTL „ Icmp Parameters „ TCP/UDP Parameters TCP PSH TCP FINTCP SYN TCP ACK „ Ethernet Type Parameters ACL Configuration wizardEtherType Filter Policy 5 for guest ports Internet access only 11-3Set up Policy Rules page screenshot Set up Port Policies Policy ID MSN Messenger Google Talk Yahoo Messenger Common ServersInstant Messaging Ethernet Type Others NetBIOS Ping Request Ping ReplySnmp Traps 173 Binding Enabled Set up Source MAC and Source IP BindingSource IP Address Set up DoS Attack Detection Rules UDP DoS Fraggle Death Icmp DoS Smurf Policy n Switch nPort n Deny 16K 32K 64K 128K ACL Rate Limiter ConfigurationRate Limiter ID 512K ACL Ports Configuration 180 Range 10-10000000 seconds Default 300 seconds MAC Address Table ConfigurationAging Configuration Address Table Static MAC Table Configuration Navigating the MAC Table MAC Address Table StatusDynamic MAC Table MAC Table Columns 184 Auto DisableMAC Table Learning Secure 186 Lldp Link Layer Discovery Protocol „ Lldp Parameters Lldp ConfigurationTx Interval Tx Hold „ 4.14.2.2 Lldp Port ConfigurationTx Delay Tx Reinit Sys Descr Port DescrSys Name Sys Capa Lldp Neighbor Lldp Statistics „ Global Counters Local Counters Network Diagnastics Cable DiagnosticsCable Status Destination IP Address PingPing Size Stacking SGSW-24040 / SGSW-24040R „ Ring topology „ Chain topology same as a disconnected ring 197 „ Removing a Switch From the Stack Switch IDs„ Assigning and Swapping Switch IDs „ Replacing a Switch Master Election „ General Switch ID Assignment RulesStack Redundancy Shortest Path Forwarding Utilize all stack links in the ring Stack Configuration „ Stack Topology Master SwitchStack Information „ Stack List „ Master Forwarding Table Stack Port State Ovewview 16-10Port State Overview page screenshot „ Identify the Master Switch Stack Example 206 207 Accessing the CLI Logon to the Console Configure IP address „ Configure IP address Switch/ ip setup 192.168.1.100 255.255.255.0 Subnet Mask Gateway Telnet login System Configuration System CommandCommand Groups Syntax System Restore Default System RebootExample System Name Default SettingSystem Prompt System Password System Sntp System Timezone System Firmware Load 217 Syntax IP ConfigurationParameters IP Setup IP Ping 220 Port Configuration Port Management CommandPort State Port Mode Port Flow Control Port Maximum Frame Port Power Port Excessive Port Statistics Port VeriPHY Port Numbers Mirror Port Mirror ConfigurationMirror SID Mirror Mode Aggregation Add Link Aggregation CommandAggregation Configuration Parameters portlist Port list Aggregation Delete Aggregation Lookup Aggregation Mode Lacp Configuration Lacp Mode Lacp Key Lacp Role Lacp Status Lacp Statistics 236 Vlan Configuration Vlan Configuration CommandVlan Mode All Vlan Frame TypeTagged Allow tagged frames only Vlan Ingress Filter Vlan Link Type Vlan Ethernet Type Vlan Q-in-Q ModeMan Set out layer Vlan tag ether type MAN Vlan Add Vlan Delete Vlan Lookup Pvlan Configuration Pvlan Isolate Rstp Configuration Spanning Tree Protocol CommandRstp SysPrio Rstp Delay Rstp Age Normal Rstp Default Setting Rstp ModeRstp Version Rstp Cost Rstp Priority Rstp Edge Rstp P2P Rstp Status Rstp Statistics Rstp mCheck Igmp Configuration Multicast Configuration CommandIgmp Mode Igmp State Igmp Querier Igmp Fast Leave Igmp Router Igmp Groups Igmp FloodingIgmp Status 256 QoS Default Quality of Service CommandQoS Configuration QoS Classes QoS Tag Priority QoS QCL Port Parameters Qclid Qclid QCL ID Default SettingQoS QCL Add Qceid QoS QCL Delete QoS QCL Lookup QoS Weight QoS ModeQoS Rate Limiter QoS Shaper QoS Unicast QoS Multicast QoS Broadcast Dot1x Configuration 802.1x Port Access Control CommandDotx1 Mode Dot1x Status Dot1x Server Dot1x Authenticate Dot1x Secret Dot1x Re-authentication Dot1x Period Dot1x Timeout Dot1x Statistics Dot1x Agetime Dot1x ClientsParameters Portlist Dot1x Holdtime ACL Configuration Access Control List CommandACL Action ACL Policy ACL Rate ACL Add ACL Delete ACL Lookup MAC Configuration MAC Address Table CommandMac Add MAC Delete MAC Lookup MAC Age Time MAC Learning MAC Dump MAC Statistics MAC Flash Lldp Configuration Lldp CommandLldp Mode Lldp Optional TLV Lldp Interval Lldp Delay Lldp Hold Lldp Reinit Lldp Information Lldp Statistics Stack List Stack Management CommandStack Master Reelect Stack SID Swap Stack SelectStack SID Delect Stack SID Asign Forwarding & Filtering LearningStore-and-Forward Auto-Negotiation If attached device is 100Base-TX port will set to 292 Why the Switch doesnt connect to the network Solution Link LED is not lit SolutionPerformance is bad Solution Switch does not power up Solution Stacking not functioning Solution „ While IP Address be changed or forgotten admin password RJ-45 Connector pin assignment Contact Switchs RJ-45 Pin Assignments10/100Mbps, 10/100Base-TX = Brown Straight Cable Straight Cable= Brown Aggregation ACEACL ARP DNS DESDhcp DoS FTP DscpEthernet Type Http Igmp IcmpIeee Imap Lldp IpmcMAC Table Mirroring NetBIOSMD5 NFS POP3 PingPolicer Private Vlan Rarp QCLQoS Samba Snmp SHASmtp Sntp Tftp TCPTelnet ToS UDP 308