Planet Technology SGSW-24040R, WGSW-24040R manual

User’s Manual of WGSW-24040 / WGSW-24040R

SGSW-24040 / SGSW-24040R

Figure 4-2-8TFTP Firmware upgrade pop-up message

Figure 4-2-9Firmware Upgrade pop-up message

4.Click “OK”, the Switch will start the TFTP upgrade procedure.

5.Please check your TFTP server application to confirm the TFTP file is well transmit to the Switch.

6.The Switch will reboot then, and It will cost 2 to 3 minutes for the TFTP firmware upgrade and reboot procedure. Please wait for the process complete.

7.Once the new software is loaded to the system successfully, the Login screen appears. Enter the user name and password to login the Switch.

DO NOT Power OFF the switch until the update progress is complete.

Do not quit the Firmware Upgrade page without press the “OK” button - after the image be loaded. Or the system won’t apply the new firmware. User has to repeat the firmware upgrade processes again.

55

Image 55

Planet Technology SGSW-24040R, WGSW-24040R user manual 8TFTP Firmware upgrade pop-up message

Contents

User’s Manual Weee Warning TrademarksDisclaimer FCC Warning CE Mark Warning Table of Conetnts 5.1 140 105118 132 187 159181 185 212 208 237 229244 257 251265 287 272277 282 297 290293 295 Product Description Packet Contents High Performance How to Use This Manual 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 Product FeaturesHigh-performance 5GbE Stacking interface ¾ Layer 2 Features ¾ Physical Port ¾ Stacking ¾ Multicast¾ Security ¾ Management Hardware Specification Product Specification Traffic classification based, Strict priority and WRR Gigabit SFP slots Switch Front PanelHardware Description Gigabit TP interface Master LED Reset buttonAbout 1~3 second Stack ID LED Indications Speed 1000Mbps 1000Base-SX/LX SFP interfaces Shared Port-21~Port-24Off To indicate that the SFP port is link down 5Rear panel of WGSW-24040 Switch Rear Panel Stack ports AC Power ReceptacleCascade UP 9SGSW-24040 / SGSW-24040R Stack Ports DC Power Connector Desktop Installation Install the Switch Rack Mounting Supply power to the Managed Switch 13Plug-in the SFP transceiver Installing the SFP transceiver „ Connect the fiber cable „ Approved Planet SFP Transceivers„ Remove the transceiver module Page Power switch in the OFF position and the DC power is OFF Connecting DC Power Supply WGSW-24040R / SGSW-24040R SGSW-24040 / SGSW-24040R Stack Installation Management Stacking Connecting Stacking cable Stack ID Master LED 21Separated Stack connection This chapter covers the following topics Requirements Administration Console Management Access OverviewMethod Advantages Disadvantages „ 115200 bps „ 8 data bits „ No parity „ 1 stop bit Direct Access Web Management 4Web main screen of Managed Switch Protocols SNMP-Based Network ManagementVirtual Terminal Protocols Management Architecture Snmp Protocol About Web-based Management WEB Configuration Http//192.168.0.100 „ Logging on the switchPage RJ-45 Ports SFP Ports Stack Ports Main WEBPanel Display State Main Menu 5WGSW/SGSW Managed Switch Main Funcrions Menu System IP Configuration System Information Page IP Configuration Password User AuthenticationOld Password New Password Sntp Configuration Click System Web Firmware Upgrade WEB Firmware Upgrade Tftp Server IP Tftp Firmware UpgradeUpgrade button Click System -TFTP Firmware Upgrade 8TFTP Firmware upgrade pop-up message „ Configuration Download Configuration Save „ Configuration Upload Configuration UploadPage Factory Default System Reboot 18Set Start-up screenshot „ Example 1 Save Current Configuration setting 19Download system software screenshot „ Example 2 Downloading System Software from a Server „ Example 3 Downloading Configuration Settings from a Server „ Example 4 Saving or Restoring Configuration Settings Snmp Operations Snmp System ConfigurationSimple Network Management Protocol Snmp Overview Write Community ModeVersion Read Community System Name Snmp System Information ConfigurationSnmp Trap Configuration System Contact Trap Destination Trap ModeTrap Version Trap Community Group Name SNMPv3 ConfigurationSNMPv3 Accesses Configuration Delete Read View Name SNMPv3 Communities ConfigurationSecurity Model Security Level Security Name SNMPv3 Groups Configuration Protocol SNMPv3 Users ConfigurationAuthentication User Name View Name SNMPv3 Views ConfigurationPrivacy Password Privacy Protocol View Type „ Example Add a new SNMPv3 userOID Subtree 9SNMPv3 Users-NEW page screenshot „ Example Add a new SNMPv3 Group 11SNMPv3 Groups-NEW page screenshot Port Management Port Configuration Flow Control Power ControlPort Link 2Port Statistics Overview page screenshot Port Statistics Overview Detailed Port Statistics Receive and Transmit Queue Counters Receive Error CountersReceive Total and Transmit Total Receive and Transmit Size Counters Transmit Error Counters Port Mirroring ConfigurationTx Drops Port to mirror to Mirror Port Configuration 6Port Mirror Configuration page screenshot „ Sgsw Stackable Switch 1Link Aggregation Link AggregationPage Destination MAC Static Aggregation ConfigurationStatic Aggregation Group Configuration Hash Code Contributors Group ID LocalityPort Members Role Lacp ConfigurationLacp Enabled Key Lacp Port Status Lacp System Status Partner Port Lacp Discarded Lacp statisticsLacp Transmitted Lacp Received Vlan Overview Vlan Ieee 802.1Q Standard Ieee 802.1Q Vlan 802.1Q Vlan Tags Port Vlan ID Vlan Classification VLANs Vlan Learning ObjectDescription Vlan ModeVlan Basic Information Supported VLANs Understand nomenclature of the Switch Vlan Port Configuration Pvid This is the logical port number for this row Port Vlan ID In-Q ModeLink Type Ether type „ Adding Static Members to VLANs Vlan Index Vlan Membership ConfigurationVlan ID „ Isolated ports Private Vlan ConfigurationOverview „ Promiscuous ports Isolated Pvlan Port TypePromiscuous Bridge Protocol Data Units Rapid Spanning Tree Protocol STP Port States Creating a Stable STP TopologyPort transitions from one state to another as follows Below ConfigurableExcept by setting priority STP Parameters STP Operation Levels Default Spanning-Tree Configuration Feature Default Value Maximum Age TimerForward Delay Timer Variable Description Default Value Port Priority Illustration of STP 110 Max Age Rstp System ConfigurationForward Delay System Priority Rstp Bridge Status Rstp Enabled Rstp Port ConfigurationPath Cost Edge PriorityPoint2Point Port Type Link Type Ieee 802.1w-2001 Ethernet Rstp Port Status TCN Rstp Port StatisticsRstp STP Understand QOS Quality of ServiceQoS Terminology Frame.The following QCE types are supported QoS Control List ConfigurationQCL # QCE Type Type Value QoS Control Entry ConfigurationTraffic Class Port QoS Configuration User Priority Default ClassQueuing Mode Queue Weighted Set up Policy Rules QCL Configuration WizardApplication Rules Port in a QCL member, click the radio button Includes the folling fileds Object DescriptionQCL ID Frames that hit this QCE are set to match this specific QCL Audio and Video Set up Typical Network Application RulesGames Buttons User DefinitionSelect the QCL ID to which these QCEs apply Set up ToS Precedence Mapping Set up Vlan Tag Priority Mapping QoS Statistics Bandwidth Control Rate Storm Control ConfigurationFrame Type Status Igmp Snooping MulticastAbout the Internet Group Management Protocol Igmp Snooping 133 0x17 Igmp Versions 10x12 „ Igmp Querier Idle Member Igmp Snooping Igmp Snooping ConfigurationFlooding enabled Enabled Igmp Querier Router Port Igmp Port Related ConfigurationFast Leave Object Description Igmp Snooping StatusVlan ID of the entry Multicast Address Table Overview of 802.1X Port-Based Authentication Ieee 802.1X Network Access ControlOverview of MAC-Based Authentication „ Device Roles Understanding Ieee 802.1X Port-Based Authentication „ Authentication Initiation and Message Exchange „ Ports in Authorized and Unauthorized States 10-2EAP message exchange Radius IP 10.2 802.1X System ConfigurationRadius Secret Period ReauthenticationEnabled EAP Timeout 10.3 802.1X and MAC-Based Authentication Port Configuration Max Clients Port State Restart Last ID 10.4 802.1X Port StatusState Last Source 10-6802.1X Statistics Port 1 page screenshot 10.5 802.1X and MAC-Based Authentication Statistics Direction Name Ieee Name Description Eapol Counters Port- and MAC-based Radius Counters Direction Name Ieee NameDescription Port-based MAC-based MAC-based „ Last Supplicant/Client Info Windows Platform Radius Server Configuration 155 „ Configure Sample EAP-MD5 Authentication 10.7 802.1X Client Configuration 157 158 Access Control List Configuration Access Control ListsIngress Port Logging ActionRate Limiter Port Copy Switch ACE Configuration Dmac Filter „ MAC Parameters„ Vlan Parameters Smac Filter ARP/ Rarp „ ARP Parameters IP Protocol Filter „ IP ParametersIP/Ethernet Length Ethernet IP TTL „ TCP/UDP Parameters „ Icmp Parameters TCP ACK TCP FINTCP SYN TCP PSH „ Ethernet Type Parameters ACL Configuration wizardEtherType Filter 11-3Set up Policy Rules page screenshot Policy 5 for guest ports Internet access only Policy ID Set up Port Policies Ethernet Type Common ServersInstant Messaging MSN Messenger Google Talk Yahoo Messenger Others NetBIOS Ping Request Ping ReplySnmp Traps 173 Binding Enabled Set up Source MAC and Source IP BindingSource IP Address UDP DoS Fraggle Set up DoS Attack Detection Rules Icmp DoS Smurf Death Deny Switch nPort n Policy n 512K ACL Rate Limiter ConfigurationRate Limiter ID 16K 32K 64K 128K ACL Ports Configuration 180 Address Table MAC Address Table ConfigurationAging Configuration Range 10-10000000 seconds Default 300 seconds Static MAC Table Configuration MAC Table Columns MAC Address Table StatusDynamic MAC Table Navigating the MAC Table 184 Secure DisableMAC Table Learning Auto 186 Link Layer Discovery Protocol Lldp „ Lldp Parameters Lldp ConfigurationTx Interval Tx Reinit „ 4.14.2.2 Lldp Port ConfigurationTx Delay Tx Hold Sys Capa Port DescrSys Name Sys Descr Lldp Neighbor „ Global Counters Lldp Statistics Local Counters Network Diagnastics Cable DiagnosticsCable Status Destination IP Address PingPing Size „ Ring topology „ Chain topology same as a disconnected ring Stacking SGSW-24040 / SGSW-24040R 197 „ Replacing a Switch Switch IDs„ Assigning and Swapping Switch IDs „ Removing a Switch From the Stack Master Election „ General Switch ID Assignment RulesStack Redundancy Utilize all stack links in the ring Shortest Path Forwarding Stack Configuration „ Stack List Master SwitchStack Information „ Stack Topology „ Master Forwarding Table 16-10Port State Overview page screenshot Stack Port State Ovewview Stack Example „ Identify the Master Switch 206 207 Logon to the Console Accessing the CLI „ Configure IP address Configure IP address Subnet Mask Gateway Switch/ ip setup 192.168.1.100 255.255.255.0 Telnet login Syntax System CommandCommand Groups System Configuration System Restore Default System RebootExample System Name Default SettingSystem Prompt System Sntp System Password System Firmware Load System Timezone 217 Syntax IP ConfigurationParameters IP Ping IP Setup 220 Port Configuration Port Management CommandPort State Port Flow Control Port Mode Port Maximum Frame Port Excessive Port Power Port VeriPHY Port Statistics Port Numbers Mirror Port Mirror ConfigurationMirror SID Mirror Mode Parameters portlist Port list Link Aggregation CommandAggregation Configuration Aggregation Add Aggregation Lookup Aggregation Delete Aggregation Mode Lacp Configuration Lacp Key Lacp Mode Lacp Status Lacp Role Lacp Statistics 236 Vlan Configuration Vlan Configuration CommandVlan Mode All Vlan Frame TypeTagged Allow tagged frames only Vlan Link Type Vlan Ingress Filter Vlan Ethernet Type Vlan Q-in-Q ModeMan Set out layer Vlan tag ether type MAN Vlan Delete Vlan Add Vlan Lookup Pvlan Isolate Pvlan Configuration Rstp Configuration Spanning Tree Protocol CommandRstp SysPrio Rstp Age Rstp Delay Normal Rstp Default Setting Rstp ModeRstp Version Rstp Priority Rstp Cost Rstp P2P Rstp Edge Rstp Status Rstp mCheck Rstp Statistics Igmp Configuration Multicast Configuration CommandIgmp Mode Igmp State Igmp Fast Leave Igmp Querier Igmp Router Igmp Groups Igmp FloodingIgmp Status 256 QoS Classes Quality of Service CommandQoS Configuration QoS Default QoS QCL Port QoS Tag Priority Qceid Qclid QCL ID Default SettingQoS QCL Add Parameters Qclid QoS QCL Lookup QoS QCL Delete QoS Weight QoS ModeQoS Rate Limiter QoS Shaper QoS Multicast QoS Unicast QoS Broadcast Dot1x Configuration 802.1x Port Access Control CommandDotx1 Mode Dot1x Server Dot1x Status Dot1x Secret Dot1x Authenticate Dot1x Period Dot1x Re-authentication Dot1x Statistics Dot1x Timeout Dot1x Agetime Dot1x ClientsParameters Portlist Dot1x Holdtime ACL Configuration Access Control List CommandACL Action ACL Rate ACL Policy ACL Add ACL Delete ACL Lookup MAC Configuration MAC Address Table CommandMac Add MAC Lookup MAC Delete MAC Learning MAC Age Time MAC Statistics MAC Dump MAC Flash Lldp Configuration Lldp CommandLldp Mode Lldp Interval Lldp Optional TLV Lldp Hold Lldp Delay Lldp Information Lldp Reinit Lldp Statistics Stack List Stack Management CommandStack Master Reelect Stack SID Swap Stack SelectStack SID Delect Stack SID Asign Forwarding & Filtering LearningStore-and-Forward If attached device is 100Base-TX port will set to Auto-Negotiation 292 Switch does not power up Solution Link LED is not lit SolutionPerformance is bad Solution Why the Switch doesnt connect to the network Solution „ While IP Address be changed or forgotten admin password Stacking not functioning Solution RJ-45 Connector pin assignment Contact Switchs RJ-45 Pin Assignments10/100Mbps, 10/100Base-TX = Brown Straight Cable Straight Cable= Brown ARP ACEACL Aggregation DoS DESDhcp DNS Http DscpEthernet Type FTP Imap IcmpIeee Igmp Lldp IpmcMAC Table NFS NetBIOSMD5 Mirroring Private Vlan PingPolicer POP3 Samba QCLQoS Rarp Sntp SHASmtp Snmp ToS TCPTelnet Tftp UDP 308