Sagem 4450E 9.2. Maintenance for Service Board, 9.2.1. Check

SAGEM 3P@C

Steps	Operation	Inspection (display of the
		indicator and screen)
	c) Pull the extractors on the both
	sides of the card, and press them
	outward, thus unplugging the card
	from the connector of the
	backboard of the chassis.
	d) Hold the front panel to unplug
	the card from the slot completely.
	e) Put the replaced card in the
	anti-static package.
Step 3	After unplugging the card, you
	should plug a new system control
	board in the void standby system
	control board slot in 60 seconds
	(see the detailed installation steps
	in the hardware installation part).
Step 4	To check whether the current	The system indicator flashes once
	standby system control board runs	per second.
	normally, execute the command:
	show boardinfo.

9.2. Maintenance for Service Board

9.2.1. Check

The corresponding status indicator in the front panel of the service board is used to display the work status of the device or the card, and it plays an important role in the fault analysis and location.

The rough position or cause of the fault can be found through the indicator status, and the indicator status is helpful for the next processing procedure. The indicator does not have the sufficient information, so it is usually used with the coordination of the alarm information analysis.

Check the system running status according to indicator description in the following table. When finding some exceptional cases, you should take some measures in time.

		The maintenance personnel should pay more attention to the
		study of the indicator meaning, and have the rapid response
	prompt	capability when some faults occur to the system.

Table 9-2 Description of the indicator of the VDUB service board

Indicator			Flag	Color	Status	Description
Status		indicator	RUN	Green	On	Power on the system.
of the VDUB					Off	No power on or the system
						runs abnormally.
					Flashing	The VDUB runs normally.
			ALM	Red	Off	The VDUB runs normally.
					ON	The VDUB has an alarm.
Status		indicator	LINK	Green	Constantly	When a stable link is built in
of	the interface				on	the user	interface,	the
of	the	VDSL				corresponding	indicator	is
user						constantly on.
					Off	This user interface does not
						connect the users.

3P@C Installation Manual

Page 9-6 Reproduction and communication in any form prohibited without the written permission of SAGEM SA

Contents

Next Generation DSLAM HARDWARE INSTALLATION MANUAL Page WARNING RECORD OF AMENDMENTS FOREWORD Page Page Page Page Page Page Page Page Page Target Readers Contents Part I Hardware Installation Part II Maintenance Appendix Common Troubleshooting & Relevant Knowledge Conventions Technical Support Hardware Installation 1.1. System Overview NG-DSLAM Management Scalable range Page 1.2. Representative Networking Applications 1.3. System Composition 1.4. Hardware Features Page 2.1. Shelf Configuration 2.1.1. Structure of the General Chassis Page 2.1.2.10U Chassis 2.1.3.Fan Module 2.1.4.Air Deflector Frame Page 2.2.Full Configuration of the Cabinet 2.3.SMUB and Service Boards 2.3.1.Service Processor Unit Board (SMUB) Page Page 2.3.2.VDSL Unit Board (VDUB) 2.3.3.ADSL Unit Board (ADUB) Page 2.3.4.ADSL Unit Card (ADUC) 2.4.Power Distribution System 2.4.1.Overview 2.4.2.Functional Features 2.5.Optional Uplink Interface Modules 2.5.1.1-portGigabit Long-waveOptical Interface Module (DS-1GLX) Page 2.5.2.1-portGigabit Short-waveOptical Interface Module (DS-1GSX) 2.5.3.2-port100M Multi-modeOptical Interface Module (DS-2FMM) 2.5.4.2-port100M Single-modeOptical Interface Module (DS-2FSM) Page 2.5.5.4-port100M Electrical Interface Module (DS-4TXB) 2.5.6. VAS Card (DS-4ITX) 2.6.Route Transfer Unit (RTU) Page 3.1.Environmental Requirements 3.1.1.Temperature and Humidity Requirements 3.1.2.Cleanness Requirements 3.1.3.Floor Requirements 3.1.4. Heat Dissipation Requirements 3.1.5.Power Supply Requirements 3.1.6.Grounding Requirements Page 3.1.7.Anti-interferenceRequirements 3.1.8.Other Requirements 3.2.Safety Requirements 3.2.1.Basic Safety Requirements 3.2.2.Antistatic Requirements 3.2.3.Avoiding Laser Damage 3.2.4.Lightning Protection Requirements 3.2.5.Anti-seismicDesign Requirements 3.2.6.Fireproof Design Requirements 3.2.7.Precautions for Equipment Handling 3.3.Installation Tools and Materials 3.4.Product Configuration List 3.4.1.Basic Configuration of the Product 3.4.2.Optional Components 3.5. Unpacking for Acceptance 3.5.1.Preparation 3.5.2.Unpacking Page Page Page 3.5.3.Goods Acceptance 4.1.Cabinet Installation 4.1.1.Installation on the Cement Floor Page Page Page Page Page 4.1.2.Installation on the Antistatic Floor Page Page Page Page Page 4.1.3.Installing the Cabinet Guide Rails 4.2.Installing the Equipment 4.2.1.Installing the 10U Chassis 4.2.2.Installing the Fan Module Page Page 4.2.3. Installing the Air Deflector Frame Page 4.3.Connecting the Power and Grounding Cables 4.3.1.Connecting the Power Cables of the Equipment 4.3.2.Connecting the Power Cable of the Fans 4.3.3.Connecting the Grounding Cables 4.3.4.Equipment Power Supply Test 4.4.Installing the Service Processor Unit Board (SMUB) 4.4.1.Installing the Uplink Interface Modules Page 4.4.2.Installing the RTU Page 4.4.3.Installing the SMUB 4.4.4.Connecting the Ethernet Interfaces of SMUB Page 4.4.5. Connecting the Optical Interfaces of SMUB 4.5.Installing the Subscriber Service Cards 4.6.Installing the Dummy Panels 4.7.Connecting the Subscriber Cables Page Page Page Page 4.8.Connecting the Console Cable Page Page Page 5.1. Requirements for Cable Types 5.2. Requirements for Cabling Length 5.3. Spacing Requirements for Indoor Cabling Page 5.4. Several Forbidden Overhead Cabling Methods 5.5. Other Requirements for Outdoor Cabling 5.6. Installing External Lightning Arrester Page Page 6.1.Equipment Power-on 6.2.Setting Up the Configuration Environment 6.2.1.Local Configuration via the Console Interface Page 6.2.2.Remote Configuration via Telnet 6.3.Command Line System 6.3.1.Command Mode 6.3.2.Common Commands 6.3.3.Online Help of Command Line 6.3.4.Command Line Edit Feature 6.4.System Management 6.4.1.Storage Media and File Type 6.4.2.Program File Management 6.4.3.Configuration File Management Maintenance 7.1.System Upgrade 7.1.1. Storage Media and File Type 7.1.2. Sequence of System Upgrade 7.1.3.Upgrading the System File Page Page Page Page Page Page Page Page 7.1.4. Upgrading the Master System Control Board Page 7.1.5.Upgrading the Standby System Control Board 7.2.Managing the Configuration File 7.2.1.Type and Format of Configuration File 7.2.2.Backuping the Configuration File 7.2.3.Loading the Configuration File 7.2.4.Erasing the Configuration File 7.3.Querying the Maintenance Information 7.3.1. Querying the Current Software Version 7.3.2.Viewing the Current Configuration 7.3.3.Querying the Port Status 7.3.4.Querying the VLAN Status 7.3.5.Viewing FIB Table 7.3.6.Viewing the ARP Table 7.3.7.Viewing the Route Information 7.3.8. Querying the System Running Time 7.4. Handling Password Loss Page Page 8.1. Checking the Optical Interface 8.2.Checking the Status of the User Port 8.2.1.Querying the ADSL Port Status Page Page 8.2.2.Querying the VDSL Port Status Page 9.1. Maintenance for System Control Board 9.1.1. Check 9.1.2. Hot Plugging 9.1.3. Master/Standby Switchover Page 9.1.4. Reset 9.1.5. Replacing System Control Board Page 9.2. Maintenance for Service Board 9.2.1. Check 9.2.2. Hot Plugging 9.2.3. Reset 9.2.4. Replacing Service Board Page Page 10.1.Checking Air-breakSwitch Page 11.1.Maintenance for Air Filter 11.1.1.Checking Air Filter 11.1.2.Cleaning and Replacing Air Filter 11.2. Maintenance for Fan Shelf 11.2.1.Checking Fan Shelf 11.2.2.Replacing Fan Shelf Page Page 12.1.Commissioning and Maintenance of ADSL Subscriber Line 12.1.1.ADSL Technical Parameters Page Page Page 12.1.2.ADSL Line Commissioning Page Page Page Page Page Page 12.1.3.ADSL Line Maintenance Page Page Page Page 12.2.Commissioning and Maintenance of the VDSL Subscriber Line 12.2.1.VDSL Technical Parameters Page 12.2.2.VDSL Line Commissioning Page Page 12.2.3.VDSL Line Maintenance Page Page Page Page 13.1.Problem Location & Information Collection 13.1.1.General Check 13.1.2.Layer-2Check 13.1.3.Layer-3Check 13.1.4.Service Check 13.2.Unstable Service due to Wrong Making of Network Cables 13.2.1.Common Causes 13.2.2.Processing Procedure 13.2.3.Typical Cases Page Page Page 14.1.Use of AC/DC Converter Page Common Troubleshooting & Relevant Knowledge A.Diagnosis of Common Faults B.Glossary