Texas Instruments TMS320DM646x manual Emac and Mdio Signals for MII Interface

www.ti.com

Architecture

		Table 1. EMAC and MDIO Signals for MII Interface
Signal	Type	Description
MTCLK	I	Transmit clock (MTCLK). The transmit clock is a continuous clock that provides the timing reference
		for transmit operations. The MTXD and MTXEN signals are tied to this clock. The clock is generated
		by the PHY and is 2.5 MHZ at 10 Mbps operation and 25 MHZ at 100 Mbps operation.
MTXD[3-0]	O	Transmit data (MTXD). The transmit data pins are a collection of 4 data signals comprising 4 bits of
		data. MTDX0 is the least-significant bit (LSB). The signals are synchronized by MTCLK and valid
		only when MTXEN is asserted.
MTXEN	O	Transmit enable (MTXEN). The transmit enable signal indicates that the MTXD pins are generating
		nibble data for use by the PHY. It is driven synchronously to MTCLK.
MCOL	I	Collision detected (MCOL). The MCOL pin is asserted by the PHY when it detects a collision on the
		network. It remains asserted while the collision condition persists. This signal is not necessarily
		synchronous to MTCLK nor MRCLK. This pin is used in half-duplex operation only.
MCRS	I	Carrier sense (MCRS). The MCRS pin is asserted by the PHY when the network is not idle in either
		transmit or receive. The pin is deasserted when both transmit and receive are idle. This signal is not
		necessarily synchronous to MTCLK nor MRCLK. This pin is used in half-duplex operation only.
MRCLK	I	Receive clock (MRCLK). The receive clock is a continuous clock that provides the timing reference
		for receive operations. The MRXD, MRXDV, and MRXER signals are tied to this clock. The clock is
		generated by the PHY and is 2.5 MHZ at 10 Mbps operation and 25 MHZ at 100 Mbps operation.
MRXD[3-0]	I	Receive data (MRXD). The receive data pins are a collection of 4 data signals comprising 4 bits of
		data. MRDX0 is the least-significant bit (LSB). The signals are synchronized by MRCLK and valid
		only when MRXDV is asserted.
MRXDV	I	Receive data valid (MRXDV). The receive data valid signal indicates that the MRXD pins are
		generating nibble data for use by the EMAC. It is driven synchronously to MRCLK.
MRXER	I	Receive error (MRXER). The receive error signal is asserted for one or more MRCLK periods to
		indicate that an error was detected in the received frame. This is meaningful only during data
		reception when MRXDV is active.
MDCLK	O	Management data clock (MDCLK). The MDIO data clock is sourced by the MDIO module on the
		system. It is used to synchronize MDIO data access operations done on the MDIO pin. The
		frequency of this clock is controlled by the CLKDIV bits in the MDIO control register (CONTROL).
MDIO	I/O	Management data input output (MDIO). The MDIO pin drives PHY management data into and out of
		the PHY by way of an access frame consisting of start of frame, read/write indication, PHY address,
		register address, and data bit cycles. The MDIO pin acts as an output for all but the data bit cycles
		at which time it is an input for read operations.

16 Ethernet Media Access Controller (EMAC)/Management Data Input/Output (MDIO) SPRUEQ6–December 2007

Submit Documentation Feedback