Avaya 1600 4. Configure ATM Options (ATM)

Avaya, Inc. - 57 - PARTNER ACS 1600 DSL module User Guide

2. Configure Receive Congestion Parameters

Follow the on-screen messages to enter the following

receive congestion parameter information.

• FECN/BECN condition set size

• FECN/BECN condition clear size

• FECN/BECN maximum number of bytes to store

Select your choice.

Your settings display in the Display Current Configuration

command in the Reports Menu. For more information, see

"Reports Menu" earlier in this chapter.

You must restart the PARTNER ACS 1600 DSL module for

any changes to take effect. For more information on

restarting the PARTNER ACS 1600 DSL module, see the

“PARTNER ACS 1600 DSL module basics” chapter.

4. Configure ATM Options (ATM)

Displays the ATM Configuration Menu, which contains the

following submenus and commands to configure the ATM

options.

1. Configure Payload Scrambling

Enables and disables payload scrambling.

2. Configure F4 OAM VPI

Sets the F4 OAM VPI value, a value between 0 and

255. Type the VPI value, and then press ENTER.

The VPI value must match the VPI from a currently

configured PVC.

3. Configure F4 OAM Type

Displays the F4 OAM Type Configuration Menu,

which contains the following options to set the F4 OAM

type.

0. None

4. F4 End to end OAM

Select your choice.

4. Display F4 OAM Configuration

Displays the F4 OAM type.

5. Send OAM Loopback

Sends an OAM Loopback cell on the port that you

select.

6. Configure EmptyCells

Configures any empty cells. Type 1 to configure idle

cells or 2 to configure unassigned cells.

Contents

Main Table of contents 1. Introduction...................................................................11 2. PARTNER ACS 1600 DSL module basics....................13 4. Menu interface...............................................................23 Page Page Page 5. Administration...............................................................86 6. WAN configuration......................................................101 7. Router configuration...................................................128 8. Bridge configuration...................................................142 Page Page 1. Introduction Organization of this guide Page 2. PARTNER ACS 1600 DSL module basics Hardware and software requirements Connectors Console cable Interfaces Page Connecting Logging on Using a terminal emulation program Using a Telnet program Page Page Menu interface Default values Restarting Auto Log off Exiting Verifying an IP address A computer running Windows 95/98/Me/2000 The PARTNER ACS 1600 DSL module 4. Menu interface Main Menu 1. Reports C. Display Current Configuration Page N. Display Network Statistics I. Display Interface Statistics M. Display Media Statistics R. Display Route Table A. Display AR P Table B. Display Bridge forwarding database S. Display Bridge status P. Display PPP Authorization Entries U. Display System Uptime Avaya, Inc. - 30 - PARTNER ACS 1600 DSL module User Guide 2. Configure IP Router Routing C. Configure Port IP Address U. Unconfigure Port IP Address S. Add/Remove a Static Route R. Enable/Disable RIP V. Configure RIP Version by Port P. Configure RIP Poisoned Reverse by Port N. Configure DNS Client H. Configure DHCP Client L. Configure DHCP Relay T. Configure Telnet Server Port F. Configure IP Filtering Page Page Page Page D. Display Route Table Avaya, Inc. - 40 - PARTNER ACS 1600 DSL module User Guide 3. Configure Bridge Displays the Bridge Configuration Menu, which contains the following submenu and commands. Bridging G. Enable/Disable Bridging Globally P. Enable/Disable Bridging by Port A. Configure Bridge Aging Timer T. Enable/Disable Spanning Tree Globally O. Enable/Disable Spanning Tree by Port Q. Configure Spanning Tree Port Priority H. Configure Spanning Tree Hello Time S. Configure Spanning Tree Max Age F. Configure Spanning Tree Forward Delay C. Configure Spanning Tree Path Cost D. Delete Bridge Forwarding Database Entry Avaya, Inc. - 44 - PARTNER ACS 1600 DSL module User Guide 5. Configure WAN SDSL WAN configuration 0. Quick Configuration 1. Configure Datalink Protocol 2. Configure Physical Interface Page 3. Configure DLCIS (Frame Relay) Page Page 3. Configure PVCS (ATM) Page Page Page 4. Configure FR Options (Frame Relay) Page 4. Configure ATM Options (ATM) 6. Configure LAN F. Set/Clear Full Duplex 7. Configure SNMP E. Enable/Disable SNMP P. Configure System Contact 8. Configure Login 1. Change User ID 2. Change User Password 3. Change NetMan Password 9. System Utilities P. Ping Utility T. Trace Route Z. Configure Console Baud Rate V. Configure Console Timeout R. Hard Reset or Reload ACOS from FLASH D. Set System Defaults W. Save System Settings as Defaults X. File Transfer Menu I. Interworking Connections 1. Add Interworking Connection Page 2. Delete Interworking Connection 3. Print Interworking Connections 4. Default Interworking Connections D. Configure DHCP Server E. Enable/Disable DHCP B. Enable/Disable DHCP Debug Messages I. Configure DHCP Server Parameters P. Configure DHCP Address Range Pool C. Configure DHCP Client Entry F. Display DHCP Configuration S. Display DHCP Server Statistics A. Display DHCP Server Assigned Addresses D. Display DHCP Entry Details X. Delete a DHCP Client Entry Y. Delete a DHCP Assignment Entry N. Configure NAT B. Enable/Disable NAT Debug Messages P. Enable/Disable NAT Translation by Port T. Configure NAT TCP Timeout U. Configure NAT UDP Timeout N. Configure NAT Local Server Entry S. Display NAT Statistics C. Display NAT Connection Table D. Display NAT Connection Details O. Display NAT Local Server Table X. Delete IP Address from NAT Tables Y. Delete NAT Local Server Entry T. Derived Timing 1. Enable/Disable Derived Timing 2. Enable/Disable Derived Timing Debug Messages Z. Diagnostics P. POTS Diagnostics S. SDSL Diagnostics C. Command Line Interface Command line syntax Commands P. VoicePath Configure V. Set Voice Gateway J. Set Jitter Delay D. Display Jitter Delay T. Set SLIC Control Mode U. Set Compander Mode (u-Law, a-Law) M. Set Debug Mode E. Configure Echo Cancellation Default Settings M. Manage MGCP/NCS Embedded Client C. Configure MGCP/NCS parameters S. Display MGCP/NCS statistics D. Debug MGCP/NCS R. Remove a connection E. CopperCom Call Control S. Statistics C. Configure D. Debug Control Page E. Call Control Settings A. Stats Display R. Ring Test S. Display IAD State T. Trace V. Pick sound heard if insufficient WAN B/W to complete call U. Configure Tollbridge Voice Client 0. Set Client IP address 1. Set Voice Gateway IP Address 2. Print Current Configuration 3. Debugging options 5. Administration Security Changing the User ID Changing the Password SNMP Enabling/disabling SNMP Configuring the System Contact Configuring the System Name Configuring the System Location Configuring the System Community Configuring the SNMP Trap Host IP Address Upgrading the system Configuring the TFTP Server Using TFTP Page Using Telnet Verifying the download Upgrading ACOS Configuring the TFTP Server Using TFTP Page Using Telnet Verifying the download Support 6. WAN configuration Changing the Datalink Protocol the Physical Interface Configuring the SDSL Interface Configuring the USI interface Page Page Quick Configuration ATM PVCs Adding a PVC Modifying a PVC Page Deleting a PVC ATM options Configuring Payload Scrambling Configuring the F4 OAM Cell Sending OAM Loopback Configuring Empty Cells Frame Relay DLCIs Adding a DLCI Page Modifying a DLCI Deleting a DLCI Frame Relay options Configuring fragmentation Page Configuring the maintenance protocol Configuring the congestion parameters the voice path Setting the jitter delay Setting the SLIC Control Mode Configuring Echo Cancellation Page Page 7. Router configuration Configuring an IP address Page Enabling RIP poisoned reverse Enabling RIP poisoned reverse globally Enabling RIP poisoned reverse by port Setting the RIP version Page Adding a static route Adding a default route Disabling bridging Disabling bridging globally Disabling bridging by port Disabling STP Disabling STP globally Disabling STP by port Page 8. Bridge configuration Enabling Bridging Enabling bridging globally Enabling bridging by port Setting the bridge aging timer Disabling RIP poisoned reverse Disabling RIP poisoned reverse globally Disabling RIP poisoned reverse by port Enabling STP Enabling STP globally Enabling STP by port Page 9. NAT configuration Enabling NAT translation the NAT local server entry the NAT timeouts Configuring a NAT TCP timeout Configuring a NAT UDP timeout the NAT port range Page 10. DHCP server configuration Enabling DHCP the DHCP server parameters Page Page the DHCP address range pool Page 11. Verification Power-up test Operational test Maintenance Displaying the current configuration A. Menu hierarchy 1. Reports C. Display Current Configuration N. Display Network Statistics I. Display Interface Statistics 2. Configure IP Router Page 3. Configure Bridge 5. Configure WAN 2. Configure Physical Interface 3. Configure DLCIs (Datalink Protocol = Frame Relay) 3. Configure PVCs (Datalink Protocol = ATM) Page Page 4. Configure FR Options (Datalink Protocol = Frame Relay) Page 9. System Utilities I. Interworking Connections 1. Add Interworking Connection D. Configure DHCP Server Page C. Command Line Interface P. VoicePath Configure Page Page B. PARTNER ACS 1600 DSL module specifications Page C. Connector pinouts Page D. USI Cables DTE or DCE? Which Hardware Protocol? Avaya, Inc. - 191 - PARTNER ACS 1600 DSL module User Guide Page E. IP Filtering Glossary Page Page Page Page Index 10 A B C Page Page Page D Page E F H I J L M N O P Q R S Page T U V W