Configuring the System Community | Avaya 1600 specs

Configuring the System Community

The value that you set must match the write community name of the SNMP host to enable the SNMP Set operation. If you enable SNMP but the community name is not set, SNMP goes into read-only mode.

To configure the system community:

1.On the Main Menu, select Configure SNMP.

The SNMP Configuration Menu displays.

*****************************************

* SNMP Configuration Menu *

*****************************************

E. Enable/Disable SNMP

P. Configure System Contact

N. Configure System Name

L. Configure System Location

C. Configure SNMP Community

T. Configure SNMP Trap Host IP Address

2.Select Configure SNMP Community.

The following instructions display on-screen:

SNMP Community is currently: Enter new SNMP Community >

3.Type the name of the SNMP community to which your system belongs or press ENTER to accept the default value that displays.

You must restart the PARTNER ACS 1600 DSL module for any changes to take effect. For more information on restarting the PARTNER ACS 1600 DSL module, see the “Getting started” chapter.

Avaya, Inc.

- 92 - PARTNER ACS 1600 DSL module User Guide

Image 93

Avaya 1600 manual Configuring the System Community, Select Configure Snmp Community

Contents

PARTNER Table of contents Menu interface Avaya, Inc Iii Partner ACS 1600 DSL module User Guide Avaya, Inc Iv Partner ACS 1600 DSL module User Guide Avaya, Inc Partner ACS 1600 DSL module User Guide Administration WAN configuration Router configuration NAT configuration USI Cables Connector pinoutsIP Filtering Glossary Organization of this guide Introduction Avaya, Inc Partner ACS 1600 DSL module User Guide Partner ACS 1600 DSL module basics ConnectorsHardware and software requirements Console cable Front View Logging on Connecting Access Level User ID Using a terminal emulation program19200 None Configuring a port IP address Using a Telnet program Select Configure Port IP Address Running the Telnet program Menu interface Default valuesRestarting Enter a new subnet mask for this interface 255.255.255.0 Exiting Auto Log offVerifying an IP address Computer running Windows 95/98/Me/2000 Partner ACS 1600 DSL module Select Display Current Configuration Main Menu Menu interface Spanning Tree bridge priority 1-65,535 default = 32,768 Display Current ConfigurationSimple Network Management Protocol Snmp enabled or disabled Reports Menu Frame Relay Management Snmp Trap Host IP Address IP address of the Snmp trap host Display Interface Statistics Display Network Statistics Display Media Statistics Clear a StatisticClear Frame Relay Dlci Statistics Clear Serial Statistics Display Route Table Display ARP TableDisplay Bridge forwarding database Spanning Tree Protocol STP enabled or disabled Display PPP Authorization EntriesDisplay Bridge status Display System Uptime Routing Configure IP Router Configure Port IP Address Unconfigure Port IP AddressAdd/Remove a Static Route Enable/Disable RIP Configure RIP Version by PortConfigure RIP Poisoned Reverse by Port Configure DNS Client Configure Dhcp ClientConfigure Dhcp Relay Configure IP Filtering Configure Telnet Server PortGlobally enable/disable input or output filters Display Dhcp Relay Statistics Toggle input or output type filters to view/edit Displays all filters of the type that you set with Source.ip.addr.high Filter Source IP High Address Display the filter in the copy buffer Deletes the filter in the copy buffer Edit the filter in the copy bufferDelete all filters of the chosen type Show IP filtering statistics Display Route Table Bridging Configure Bridge Enable/Disable Bridging by Port Enable/Disable Bridging GloballyConfigure Bridge Aging Timer Enable/Disable Spanning Tree Globally Configure Spanning Tree Hello Time Configure Spanning Tree Port PriorityConfigure Spanning Tree Max Age Configure Spanning Tree Forward Delay Delete Bridge Forwarding Database Entry WAN Configure Configure Datalink Protocol Quick Configuration Set WAN interface type Configure Physical InterfaceRS-530 Externally provided MBps KBps Sdsl Mode Set Sdsl Sync Delay LucentSet Sdsl to AccessLan CPE Mode Set Sdsl Speed Manually Configure Dlcis Frame Relay Set Fragmentation Size Configure Receive CIR Modify Existing Dlci Delete Dlci Configure Pvcs ATMShow Current DLCIs Add New PVC Proprietary Voice RFC 2364 PPPoATM with LLC EncapsulationNone PAP Client PAP Server Chap Client Chap Server Modify Existing PVC RFC 2364 PPPoATM using VC Muxing Proprietary Voice Enable/Disable FRF.12 Configure FR Options Frame RelayEnable Automatic Fragment Sizing Set Manual Fragment Size Delete PVC Enable/Disable CuMtn Fragmentation Configure Copper Mountain FragmentationConfigure Congestion Parameters Configure Transmit Congestion Parameters Configure ATM Options ATM Configure Receive Congestion ParametersConfigure EmptyCells Configure System Contact Enable/Disable SnmpConfigure System Name Configure System Location Configure Login System Utilities Ping UtilityTrace Route Configure Console Timeout Configure Console Baud RateHard Reset or Reload Acos from Flash Set System Defaults File Transfer Menu Interworking Connections Update Entire SystemAdd Interworking Connection File Transfer Utilities True Set FR-SSCS, ATM =Always Always Map FR Fecn to ATM Efci 1. Always Print Interworking Connections Delete Interworking ConnectionAlways Map FR Fecn to ATM Efci False Always Map FR Fecn to ATM Efci Map FR DE to ATM Clpi Default Interworking Connections Configure Dhcp ServerEnable/Disable Dhcp Enable/Disable Dhcp Debug Messages Configure Dhcp Client Entry Configure Dhcp Address Range Pool Display Dhcp Server Statistics Display Dhcp Configuration Display Dhcp Server Assigned Addresses Nacks sent Requests for other servers Protocol errorsDisplay Dhcp Entry Details Delete a Dhcp Client Entry Enable/Disable NAT Translation by Port Enable/Disable NAT Debug MessagesConfigure NAT TCP Timeout Configure NAT UDP Timeout Display NAT Statistics Configure NAT Local Server Entry Display NAT Connection Details Display NAT Connection TableDisplay NAT Local Server Table Delete IP Address from NAT Tables Enable/Disable Derived Timing Debug Messages Enable/Disable Derived TimingDerived Timing Delete NAT Local Server Entry Pots Diagnostics Diagnostics MenuSdsl Diagnostics Hotline Test Ring Test On/Off Hook Test Command Line Interface Command line syntaxCommands VoicePath Configure Set Jitter DelaySet Voice Gateway Set Slic Control Mode Display Jitter DelaySet Compander Mode u-Law, a-Law Auto Control Mode Manual Control Mode Configure Echo Cancellation Default Settings Set Debug ModeEnable Debug Disable Debug Configure Echo Cancellation default setting per port Manage MGCP/NCS Embedded Client Configure MGCP/NCS parametersDisplay MGCP/NCS statistics Debug MGCP/NCS CopperCom Call Control ConfigureStatistics Debug Control Flags Payload CPE Signal GWY Signal Display Debug State/Flags Configure Ring Test Call Control SettingsStats Display Ring Test Trace Display IAD StateDisplay Parameters Set Trace data Print Current Configuration Configure Tollbridge Voice ClientPick sound heard if insufficient WAN B/W to complete call Set Client IP address Debugging options Security Administration Access level Menu access level Changing the PasswordChanging the User ID Select Change User ID Configuring Select Change User Password or Change NetMan PasswordEnter new Password up to 17 characters Snmp Configuration Menu displays Configuring the System ContactSelect Enable/Disable Snmp Enabling/disabling Snmp Configuring the System Name Select Configure System ContactSelect Configure System Name Configuring the System Location Select Configure Snmp Community Configuring the System Community Upgrading the system Configuring the Snmp Trap Host IP Address Using Tftp Configuring the Tftp Server Select File Transfer Menu File Transfer Menu displays Select Update Entire SystemFile Transfer Method Receive via Tftp Receive via Xmodem Select Receive via Tftp Using Telnet Verifying the downloadSelect File System Menu File System Menu displays Acos Upgrading Select File Transfer Menu File Transfer Menu displays Select Update Acos acos.bin Support Changing Datalink Protocol WAN configuration Configuring Physical Interface WAN Configuration Menu displays Configuring the Sdsl InterfaceSelect Configure Physical Interface Available WAN Interfaces Configuring the USI interface Avaya, Inc Partner ACS 1600 DSL module User Guide Select Set WAN interface type Quick Configuration Select Quick Configuration Configuring ATM PVCs ATM Encapsulation Configuration submenu displays Adding a PVCSelect Add New PVC ATM Service Category Configuration CBR UBR Modifying a PVCSelect Modify Existing PVC ATM Encapsulation Configuration submenu displays Configuring ATM options Deleting a PVCSelect Delete PVC Configuring the F4 OAM Cell Configuring Payload Scrambling Sending OAM Loopback F4 OAM Type Configuration Menu None F4 End to end OAM Select Configure EmptyCells Configuring Empty CellsSelect Send OAM Loopback Empty Cells are currently Idle Adding a Dlci Configuring Frame Relay DLCIsEnter 1 for Idle cells or 2 for Unassigned cells Select Add New Dlci FR Encapsulation Configuration submenu displays Select Modify Existing Dlci Modifying a Dlci Deleting a Dlci Configuring fragmentation Configuring Frame Relay optionsWAN Configuration Menu displays Select Configure FR Options Select Delete Dlci Do one of the following Configuring the maintenance protocol UserBoth Configuring the congestion parameters Setting the jitter delay Configuring the voice pathSelect Set Jitter Delay Enter number of ms to delay Configuring Echo Cancellation Setting the Slic Control Mode Display current Echo Cancellation default settings Avaya, Inc Partner ACS 1600 DSL module User Guide Configuring an IP address Router configuration Router Configuration Menu displays Enabling RIP poisoned reverse Router Configuration Menu redisplays Enabling RIP poisoned reverse globally Enabling RIP poisoned reverse by port Setting the RIP version Avaya, Inc Partner ACS 1600 DSL module User Guide Select Add a Static Route Adding a static route Router Modification Menu redisplays Adding a default route Bridge Configuration Menu displays Select Add/Change the Default RouteDisabling bridging Disabling bridging globally Bridge Configuration Menu Configure Spanning Tree Bridge PriorityDisabling bridging by port Disabling STP globally Disabling STP Disabling STP by port Bridge Configuration Menu redisplays Bridge configuration Enabling bridging globally Enabling Bridging Enabling bridging by port Enter Bridge Aging time in seconds 1..3600 Setting the bridge aging timer Disabling RIP poisoned reverse globally Disabling RIP poisoned reverse Disabling RIP poisoned reverse by port Router Configuration Menu resplays Enabling STP globally Enabling STP Enabling STP by port Bridge Configuration Menu redisplays NAT configuration NAT Configuration Menu displays NAT Configuration Menu redisplaysEnabling NAT translation Enter NAT Local Server Entry to Configure 1..10 Configuring the NAT local server entry Enter NAT Local Server Protocol 1=TCP 2=UDP Configuring the NAT timeouts Configuring a NAT TCP timeout Select Configure NAT TCP TimeoutEnter NAT TCP Connection Timeout in seconds 60..3600 Configuring a NAT UDP timeout Select Configure NAT UDP TimeoutEnter NAT UDP Connection Timeout in seconds 60..3600 Configuring the NAT port range Select Configure NAT Port Range Enter Low End of NAT Port Range 5000..65534Enter High End of NAT Port Range 5010..65534 Dhcp server configuration Dhcp Server Configuration Menu displaysEnabling Configuring the Dhcp server parameters Select Enable/Disable DhcpDelete a Dhcp Assignment Entry Type the new gateway IP address, and then press Dhcp Server Configuration Menu redisplays NetBIOS Type Configuration Menu displays Configuring Dhcp address range pool Avaya, Inc Partner ACS 1600 DSL module User Guide Power-up test VerificationOperational test Maintenance Displaying the current configuration Menu hierarchy Display Current Configuration Display Network Statistics Configure IP Router Configure Telnet Server Port Configure IP Filtering Configure Dhcp Client Configure Dhcp Relay Totally Transparent Raw Hdlc Cisco compatible Hdlc USI Configure DLCIs Datalink Protocol = Frame Relay Configure PVCs Datalink Protocol = ATM Avaya, Inc Partner ACS 1600 DSL module User Guide Avaya, Inc Partner ACS 1600 DSL module User Guide Configure FR Options Datalink Protocol = Frame Relay Change User ID Change User Password Change NetMan Password Configure ATM Options Datalink Protocol = ATM Ping Utility Trace Route Configure Console Baud Rate Interworking Connections Always Map Fr Fecn To ATM Efci Map Fr De To ATM Clpi Hotline Test Ring Test Set Jitter Delay Display Jitter Delay Set Slic Control Mode Command Line Interface VoicePath Configure Display Statistics C. Clear Statistics Display IAD State Trace Stats Display Ring Test Network Interfaces Partner ACS 1600 DSL module specificationsBridging Routing Protocols Environmental Management and Configuration 10BaseT Connector Connector pinouts100BaseT Connector Pin Signal Connector USI Cables DTE or DCE?Which Hardware Protocol? Signal RS-530 RS-449 Signal RS-530 IP Filtering Glossary Inverse ARP Icmp OSI Reference MAC address Reverse PoisonedRouter Subnet Mask SVC Index Partner ACS Avaya, Inc Partner ACS 1600 DSL module User Guide Avaya, Inc Partner ACS 1600 DSL module User Guide Partner ACS Avaya, Inc Partner ACS 1600 DSL module User Guide Eeprom Avaya, Inc Partner ACS 1600 DSL module User Guide Avaya, Inc Partner ACS 1600 DSL module User Guide Avaya, Inc Partner ACS 1600 DSL module User Guide Avaya, Inc Partner ACS 1600 DSL module User Guide STP Telnet Avaya, Inc Partner ACS 1600 DSL module User Guide