Chapter 10 Configuring IEEE 802.1x Port-Based Authentication

Configuring IEEE 802.1x Authentication

 

Command

Purpose

Step 4

 

 

dot1x port-control auto

Enable IEEE 802.1x authentication on the port.

Step 5

 

 

dot1x auth-fail vlan vlan-id

Specify an active VLAN as an IEEE 802.1x restricted VLAN. The range

 

 

is 1 to 4094.

 

 

You can configure any active VLAN except an internal VLAN (routed

 

 

port), an RSPAN VLAN, a primary private VLAN, or a voice VLAN as

 

 

an IEEE 802.1x restricted VLAN.

Step 6

 

 

end

Return to privileged EXEC mode.

Step 7

 

 

show dot1x interface interface-id

(Optional) Verify your entries.

Step 8

 

 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

 

 

 

To disable and remove the restricted VLAN, use the no dot1x auth-fail vlan interface configuration command. The port returns to the unauthorized state.

This example shows how to enable VLAN 2 as an IEEE 802.1x restricted VLAN:

Switch(config)# interface gigabitethernet2/0/2

Switch(config-if)#dot1x auth-fail vlan 2

You can configure the maximum number of authentication attempts allowed before a user is assigned to the restricted VLAN by using the dot1x auth-failmax-attemptsinterface configuration command. The range of allowable authentication attempts is 1 to 3. The default is 3 attempts.

Beginning in privileged EXEC mode, follow these steps to configure the maximum number of allowed authentication attempts. This procedure is optional.

 

Command

Purpose

Step 1

 

 

configure terminal

Enter global configuration mode.

Step 2

 

 

interface interface-id

Specify the port to be configured, and enter interface configuration mode.

 

 

For the supported port types, see the “IEEE 802.1x Authentication

 

 

Configuration Guidelines” section on page 10-23.

Step 3

 

 

switchport mode access

Set the port to access mode,

 

or

or

 

switchport mode private-vlan host

Configure the Layer 2 port as a private-VLAN host port.

Step 4

 

 

dot1x port-control auto

Enable IEEE 802.1x authentication on the port.

Step 5

 

 

dot1x auth-fail vlan vlan-id

Specify an active VLAN as an IEEE 802.1x restricted VLAN. The range

 

 

is 1 to 4094.

 

 

You can configure any active VLAN except an internal VLAN (routed

 

 

port), an RSPAN VLAN, a primary private VLAN, or a voice VLAN as

 

 

an IEEE 802.1x restricted VLAN.

Step 6

 

 

dot1x auth-fail max-attempts max

Specify a number of authentication attempts to allow before a port moves

 

attempts

to the restricted VLAN. The range is 1 to 3, and the default is 3.

Step 7

 

 

end

Return to privileged EXEC mode.

Step 8

 

 

show dot1x interface interface-id

(Optional) Verify your entries.

Step 9

 

 

copy running-config startup-config

(Optional) Save your entries in the configuration file.

 

 

 

 

 

Catalyst 3750-E and 3560-E Switch Software Configuration Guide

 

 

 

 

 

 

OL-9775-02

 

 

10-35

 

 

 

 

 

Page 287
Image 287
Cisco Systems 3750E manual Dot1x auth-fail vlan vlan-id, Dot1x auth-fail max-attempts max, Attempts, 10-35