Delta Electronics VFD-VE Series manual Summary of Parameter Settings, Group 0 System Parameters

Chapter 4 Parameters

4.1 Summary of Parameter Settings

:The parameter can be set during operation.

Group 0 System Parameters

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
00-00		Identity Code of the AC	Read-only	0	○	○	○	○	○
		motor drive
00-01		Rated Current Display of	Read-only	0	○	○	○	○	○
		the AC motor drive
			0: No function	0	○	○	○	○	○
			1: Read only
			2: Enable group 11 parameters setting
00-02		Parameter Reset	8: Keypad lock
			9: All parameters are reset to factory settings (50Hz,
			220V/380V)
			10: All parameters are reset to factory settings (60Hz,
			220V/440V)
			0: Display the frequency command value (LED F)	0	○	○	○	○	○
00-03		Start-up Display Selection	1: Display the actual output frequency (LED H)
			2: Multifunction display, see Pr.00-04 (LED U)
			3: Display the output current (A)
			0: Display output current (A)	0	○	○	○	○	○
			1: Display counter value (C)
			2: Display output frequency (H)
			3: Display DC-BUS voltage ( u )
			4: Display output voltage (E)
			5: Output power factor angle (n)
			6: Display output power (kW)
			7: Display actual motor speed (HU)
			8: Display estimate output torque (kg-m)
			9: Display PG position (G) (refer to Pr.10-00 and Pr.10-
			01)
		Content of Multi Function	10: Display PID feedback
00-04			11: Display AVI (%)
		Display
			12: Display ACI (%)
			13: Display AUI (%)
			14: Display the temperature of heat sink (°C)
			15: Display the temperature of IGBT (°C)
			16: The status of digital input (ON/OFF)
			17: The status of digital output (ON/OFF)
			18: Multi-step speed
			19: The corresponding CPU pin status of digital input
			20: The corresponding CPU pin status of digital output
			21: Number of actual motor revolution (PG1 of PG card)
			22: Pulse input frequency (PG2 of PG card)
			23: Pulse input position (PG2 of PG card)
00-05		User-Defined Coefficient K	Digit 4: decimal point number (0 to 3)	0	○	○	○	○	○
			Digit 0-3: 40 to 9999
00-06		Software Version	Read-only	#.#	○	○	○	○	○
00-07		Password Input	1 to 9998 and 10000 to 65535	0	○	○	○	○	○
			0 to 2: times of wrong password
			1 to 9998 and 10000 to 65535	0	○	○	○	○	○
00-08		Password Set	0: No password set or successful input in Pr.00-07
			1: Password has been set
00-09		Energy Saving Gain	10~1000 %	100%				○
			0: V/f Control	0	○	○	○	○	○
		Control Method	1: V/f Control + Encoder (VFPG)
00-10			2: Sensorless vector control (SVC)
			3: FOC vector control + Encoder (FOCPG)
			4: Torque control + Encoder (TQRPG)
			0: V/f curve determined by group 01	0	○	○
00-11		V/f Curve Selection	1: 1.5 power curve
			2: Square curve
		Constant/Variable Torque	0: Constant Torque (100%)	0	○	○	○	○
00-12			1: Variable Torque (125%)
		Selection
		Optimal	0: Linear accel./decel. I	0	○	○	○	○
			1: Auto accel., linear decel.
00-13		Acceleration/Deceleration
			2: Linear accel., auto decel.
		Setting	3: Auto accel./decel.

4-2 Revision August 2008, 03VE, SW V2.04