Delta Electronics VFD-VE Series manual Crane function

Chapter 4 Parameters

Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
			Setting
02-35	Multi-function Output 5 (MO3)	33: Zero speed (actual output		○	○	○	○
		frequency)
	Multi-function Output 6 (MO4)
02-36		34: Zero speed with Stop (actual output		○	○	○	○
		frequency)
02-37	Multi-function Output 7 (MO5)	35: Error output selection 1 (Pr.06-23)		○	○	○	○	○
	Multi-function Output 8 (MO6)
02-38		36: Error output selection 2 (Pr.06-24)		○	○	○	○	○
	Multi-function Output 9 (MO7)
02-39		37: Error output selection 3 (Pr.06-25)		○	○	○	○	○
	Multi-function Output 10 (MO8)
02-40		38: Error output selection 4 (Pr.06-26)		○	○	○	○	○
	Multi-function Output 11 (MO9)
02-41		39: Position attained (Pr.10-19)					○
	Multi-function Output 12 (MOA)
02-42		40: Speed attained (including zero		○	○	○	○
		speed)
		41: Multi-position attained					○
		42: Crane function		○	○	○	○

Group 3 Analog Input/Output Parameters

In version 2.02, the parameters are from Pr.03-00 to Pr.03-20. The settings for Pr.03-00 to Pr.03-02 are from 0 to 10

Pr.		Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
03-00	Analog Input 1 (AVI)		2: torque command (torque limit under	0					○
			speed mode)
			3: Torque compensation command		○	○	○	○	○
	Analog Input 2 (ACI)
03-01			4: PID target value (refer to group 8)		○	○	○	○
			5: PID feedback signal (refer to group		○	○	○	○
	Analog Input	3 (AUI)	8)
03-02			6: P.T.C. thermistor input value		○	○	○	○	○
			7: Positive torque limit					○
			8: Negative torque limit					○
			9: Regenerative torque limit					○
			10: Positive/negative torque limit					○
03-20	Analog Output Value in REV Direction		0: Absolute value in REV direction	0	○	○	○	○	○
			1: Output 0V in REV direction
			2: Enable output voltage in REV
			direction

Group 6 Protection Parameters

In version 2.02, the parameters are from Pr.06-00 to Pr.06-31. The settings of Pr.06-01 are shown as follows. The settings for Pr.06-17 to Pr.06-22 are from 0 to 62.

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
06-01		Over-voltage Stall Prevention	0.0: Disable
			350.0~450.0Vdc	380.0	○	○	○	○	○
			700.0~900.0Vdc	760.0	○	○	○	○	○
	06-17	Present Fault Record	0: No fault	0	○	○	○	○	○
	06-18	Second Most Recent Fault Record	1: Over-current during acceleration	0	○	○	○	○	○
	06-19	Third Most Recent Fault Record	(ocA)	0	○	○	○	○	○
			2: Over-current during deceleration
06-20		Fourth Most Recent Fault Record		0	○	○	○	○	○
			(ocd)
	06-21	Fifth Most Recent Fault Record	3: Over-current during constant speed	0	○	○	○	○	○
	06-22	Sixth Most Recent Fault Record	(ocn)	0	○	○	○	○	○

Revision August 2008, 03VE, SW V2.04 4-27