Delta Electronics VFD-VE Series manual Group 3 Analog Input/Output Parameters, Aui

Chapter 4 Parameters

Group 3 Analog Input/Output Parameters

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
03-00		Analog Input 1 (AVI)	0: No function	1	○	○	○	○	○
03-01		Analog Input 2 (ACI)	1: Frequency command (torque limit under TQR control	0	○	○	○	○	○
			mode)
03-02		Analog Input 3 (AUI)	2: torque command (torque limit under speed mode)	0					○
			3: Torque compensation command		○	○	○	○	○
			4: PID target value (refer to group 8)		○	○	○	○
			5: PID feedback signal (refer to group 8)		○	○	○	○
			6: P.T.C. thermistor input value		○	○	○	○	○
			7: Positive torque limit					○
			8: Negative torque limit					○
			9: Regenerative torque limit					○
			10: Positive/negative torque limit					○
			11: PID feedback signal of tension		○	○	○	○	○
			12: Line speed		○	○	○	○	○
			13: Reel diameter		○	○	○	○	○
			14: PID target value of tension (tension closed-loop)		○	○	○	○	○
			15: Tension setting (tension open-loop)						○
			16: Zero-speed tension						○
			17: Tension taper						○
03-03		Analog Input Bias 1	-100.0~100.0%	0	○	○	○	○	○
		(AVI)
03-04		Analog Input Bias 2	-100.0~100.0%	0	○	○	○	○	○
		(ACI)
03-05		Analog Input Bias 3	-100.0~100.0%	0	○	○	○	○	○
		(AUI)
03-06		Positive/negative Bias	0: Zero bias	0	○	○	○	○	○
		Mode (AVI)	1: Lower than bias=bias
03-07		Positive/negative Bias	2: Greater than bias=bias	0	○	○	○	○	○
		Mode (ACI)	3: The absolute value of the bias voltage while serving
03-08		Positive/negative Bias	as the center	0	○	○	○	○	○
		Mode (AUI)	4: Serve bias as the center
03-09		Analog Input Gain 1	-500.0~500.0%	100.0	○	○	○	○	○
		(AVI)
03-10		Analog Input Gain 2	-500.0~500.0%	100.0	○	○	○	○	○
		(ACI )
03-11		Analog Input Gain 3	-500.0~500.0%	100.0	○	○	○	○	○
		(AUI)
03-12		ACI/AVI2 Selection	0: ACI	0	○	○	○	○	○
			1: AVI 2
03-13		Analog Input Delay	0.00~2.00 sec	0.01	○	○	○	○	○
		Time (AVI)
03-14		Analog Input Delay	0.00~2.00 sec	0.01	○	○	○	○	○
		Time (ACI)
03-15		Analog Input Delay	0.00~2.00 sec	0.01	○	○	○	○	○
		Time (AUI)
03-16		Addition Function of	0: Disable (AVI, ACI, AUI)		○	○	○	○	○
		the Analog Input	1: Enable
03-17		Loss of the ACI Signal	0: Disable	0	○	○	○	○	○
			1: Continue operation at the last frequency
			2: Decelerate to stop
			3: Stop immediately and display E.F.
03-18		Analog Output	0: Output frequency (Hz)	0	○	○	○	○	○
		Selection 1	1: Frequency command (Hz)		○	○	○	○	○
03-21		Analog Output	2: Motor speed (Hz)		○	○	○	○	○
		Selection 2	3: Output current (rms)		○	○	○	○	○
03-24		Analog Output	4: Output voltage		○	○	○	○	○
		Selection 3	5: DC Bus Voltage		○	○	○	○	○
			6: Power factor		○	○	○	○	○
			7: Power		○	○	○	○	○
			8: Output torque		○	○	○	○	○

Revision August 2008, 03VE, SW V2.04 4-9