Delta Electronics VFD-VE Series manual New settings 44~50 for Pr.02-00~Pr.02-06 and new parameter

Chapter 4 Parameters

New settings 44~50 for Pr.02-00~Pr.02-06 and new parameter 02-43.

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
02-00		2-wire/3-wire Operation	0: FWD/STOP, REV/STOP	0	○	○	○	○	○
		Control	1: FWD/STOP, REV/STOP (Line Start Lockout)
			2: RUN/STOP, REV/FWD
			3: RUN/STOP, REV/FWD (Line Start Lockout)
			4: 3-wire (momentary push button)
			5: 3-wire (momentary push button and Line Start
			Lockout)
02-01		Multi-Function Input	0: no function	1	○	○	○	○	○
		Command 1 (MI1)	1: multi-step speed command 1/multi-step position		○	○	○	○
		(it is Stop terminal for 3-	command 1
		wire operation)	2: multi-step speed command 2/ multi-step position		○	○	○	○
			command 2
	02-02		3: multi-step speed command 3/ multi-step position	2	○	○	○	○
		Multi-Function Input	command 3
		Command 2 (MI2)	4: multi-step speed command 4/ multi-step position		○	○	○	○
			command 4
	02-03	Multi-Function Input	5: Reset	3	○	○	○	○	○
		Command 3 (MI3)	6: JOG command		○	○	○	○
	02-04	Multi-Function Input	7: acceleration/deceleration speed inhibit	4	○	○	○	○
		Command 4 (MI4)	8: the 1st, 2nd acceleration/deceleration time selection		○	○	○	○
	02-05	Multi-Function Input	9: the 3rd, 4th acceleration/deceleration time selection	0	○	○	○	○
		Command 5 (MI5)	10: EF input (07-36)		○	○	○	○	○
	02-06	Multi-Function Input	11: B.B. input	0	○	○	○	○	○
		Command 6 (MI6)	12: Output stop		○	○	○	○	○
		(specific terminal for
		TRG)
02-23		Multi-Function Input	13: cancel the setting of the optimal	0	○	○	○	○
		Command 7	acceleration/deceleration time
02-24		Multi-Function Input	14: switch between drive settings 1 and 2	0	○	○	○	○
		Command 8
02-25		Multi-Function Input	15: operation speed command form AVI	0	○	○	○	○
		Command 9
02-26		Multi-Function Input	16: operation speed command form ACI	0	○	○	○	○
		Command 10
02-27		Multi-Function Input	17: operation speed command form AUI	0	○	○	○	○
		Command 11
02-28		Multi-Function Input	18: Emergency Stop (07-36)	0	○	○	○	○	○
		Command 12
02-29		Multi-Function Input	19: Digital Up command	0	○	○	○	○
		Command 13
02-30		Multi-Function Input	20: Digital Down command	0	○	○	○	○
		Command 14
			21: PID function disabled		○	○	○	○
			22: clear counter		○	○	○	○	○
			23: input the counter value (multi-function input		○	○	○	○	○
			command 6)
			24: FWD JOG command		○	○	○	○
			25: REV JOG command		○	○	○	○
			26: TQC+PG/FOC+PG model selection					○	○
			27: ASR1/ASR2 selection			○		○
			28: Emergency stop (EF1)		○	○	○	○	○
			29: Signal confirmation for Y-connection		○	○	○	○
			30: Signal confirmation for Δ−connection		○	○	○	○
			31: High torque bias (by Pr.07-29)		○	○	○	○	○
			32: Middle torque bias (by Pr.07-30)		○	○	○	○	○
			33: Low torque bias (by Pr.07-31)		○	○	○	○	○
			34: Enable multi-step position control			○		○
			35: Enable position control			○		○
			36: Enable position learning function (valid at stop)			○		○
			37: Enable pulse position input command			○		○
			38: Disable write EEPROM function		○	○	○	○	○
			39: Torque command direction						○
			40: Force stop		○	○	○	○	○
			41: Serial position clock					○
			42: Serial position input					○
			43: Analog input resolution selection					○

4-30 Revision August 2008, 03VE, SW V2.04