Delta Electronics VFD-VE Series manual Group 6 Protection Parameters

Chapter 4 Parameters

Group 6 Protection Parameters

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
06-00		Low Voltage Level	160.0~220.0Vdc	180.0	○	○	○	○	○
			320.0~440.0Vdc	360.0	○	○	○	○	○
06-01		Over-voltage Stall	0.0: Disable
		Prevention	350.0~450.0Vdc	380.0	○	○	○	○	○
			700.0~900.0Vdc	760.0	○	○	○	○	○
06-02		Phase-loss Protection	0: Warn and keep operation	0	○	○	○	○	○
			1: Warn and ramp to stop
			2: Warn and coast to stop
06-03		Over-current Stall	00~250%	170	○	○	○
		Prevention during
		Acceleration
06-04		Over-current Stall	00~250%	170	○	○	○
		Prevention during
		Operation
06-05		Accel./Decel. Time	0: by current accel/decel time	0	○	○	○
		Selection of Stall	1: by the 1st accel/decel time
		Prevention at constant	2: by the 2nd accel/decel time
		speed	3: by the 3rd accel/decel time
			4: by the 4th accel/decel time
			5: by auto accel/decel time
06-06		Over-torque Detection	0: disable	0	○	○	○	○	○
		Selection (OT1)	1: over-torque detection during constant speed
			operation, continue to operate after detection
			2: over-torque detection during constant speed
			operation, stop operation after detection
			3: over-torque detection during operation, continue to
			operate after detection
			4: over-torque detection during operation, stop
			operation after detection
06-07		Over-torque Detection	10~250%	150	○	○	○	○	○
		Level (OT1)
06-08		Over-torque Detection	0.0~60.0 sec	0.1	○	○	○	○	○
		Time (OT1)
06-09		Over-torque Detection	0: disable	0	○	○	○	○	○
		Selection (OT2)	1: over-torque detection during constant speed
			operation, continue to operate after detection
			2: over-torque detection during constant speed
			operation, stop operation after detection
			3: over-torque detection during operation, continue to
			operate after detection
			4: over-torque detection during operation, stop
			operation after detection
06-10		Over-torque Detection	10~250%	150	○	○	○	○	○
		Level (OT2)
06-11		Over-torque Detection	0.0~60.0 sec	0.1	○	○	○	○	○
		Time (OT2)
	06-12	Current Limit	0~250%	150				○	○
06-13		Electronic Thermal	0: Inverter motor	2	○	○	○	○	○
		Relay Selection (Motor	1: Standard motor
		1)	2: Disable
06-14		Electronic Thermal	30.0~600.0 sec	60.0	○	○	○	○	○
		Characteristic for
		Motor 1
06-15		Heat Sink Over-heat	0.0~110.0 °C	85.0	○	○	○	○	○
		(OH) Warning
06-16		Stall Prevention Limit	0~100% (refer to Pr.06-03, Pr.06-04)	50	○	○	○
		Level
	06-17	Present Fault Record	0: No fault	0	○	○	○	○	○
			1: Over-current during acceleration (ocA)		○	○	○	○	○
06-18		Second Most Recent	2: Over-current during deceleration (ocd)	0	○	○	○	○	○
		Fault Record	3: Over-current during constant speed (ocn)		○	○	○	○	○
			4: Ground fault (GFF)		○	○	○	○	○
06-19		Third Most Recent	5: IGBT short-circuit (occ)	0	○	○	○	○	○
		Fault Record	6: Over-curent at stop (ocS)		○	○	○	○	○
			7: Over-voltage during acceleration (ovA)		○	○	○	○	○
	06-20	Fourth Most Recent	8: Over-voltage during deceleration (ovd)	0	○	○	○	○	○
		Fault Record	9: Over-voltage during constant speed (ovn)		○	○	○	○	○
			10: Over-voltage at stop (ovS)		○	○	○	○	○

Revision August 2008, 03VE, SW V2.04 4-13