Delta Electronics VFD-VE Series manual Group 7 Special Parameters

Chapter 4 Parameters

Group 7 Special Parameters

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
07-00		Software Brake Level	230V: 350.0~450.0Vdc	380.0	○	○	○	○	○
			460V: 700.0~900.0Vdc	760.0
07-01		DC Brake Current	0~100%	0				○	○
		Level
07-02		DC Brake Time during	0.0~60.0 sec	0.0				○	○
		Start-up
07-03		DC Brake Time during	0.0~60.0 sec	0.0				○	○
		Stopping
07-04		Start-point for DC	0.00~600.00Hz	0.00	○	○	○
		Brake
	07-05	DC Brake Voltage	1~500	50	○	○	○
		Gain
07-06		Momentary Power	0: Operation stop after momentary power loss	0	○	○	○	○	○
		Loss Operation	1: Operation continues after momentary power loss,
		Selection	speed search starts with the Master Frequency
			reference value
			2: Operation continues after momentary power loss,
			speed search starts with the minimum frequency
07-07		Maximum Allowable	0.1~5.0 sec	2.0	○	○	○	○	○
		Power Loss Time
07-08		B.B. Time for Speed	0.1~5.0 sec	0.5	○	○	○	○	○
		Search
07-09		Current Limit for	20~200%	150	○	○	○	○	○
		Speed Search
07-10		Base-block Speed	0: Stop operation	0	○	○	○	○	○
		Search	1: Speed search starts with last frequency command
			2: Speed search starts with minimum output frequency
07-11		Auto Restart after	0~10	0	○	○	○	○	○
		Fault
07-12		Speed Search during	0: Disable	0	○	○	○	○
		Start-up	1: Speed search from maximum frequency
			2: Speed search from start-up frequency
			3: Speed search from minimum frequency
07-13		Decel. Time Selection	0: Disable	0	○	○	○	○	○
		for Momentary Power	1: 1st decel. time
		Loss	2: 2nd decel. time
			3: 3rd decel. time
			4: 4th decel. time
			5: Current decel. time
			6: Auto decel. Time
	07-14	DEB Return Time	0.0~25.0 sec	0.0	○	○	○	○
	07-15	Dwell Time at Accel.	0.00~600.00sec	0.00	○	○	○	○
07-16		Dwell Frequency at	0.00~600.00Hz	0.00	○	○	○	○
		Accel.
	07-17	Dwell Time at Decel.	0.00~600.00sec	0.00	○	○	○	○
07-18		Dwell Frequency at	0.00~600.00Hz	0.00	○	○	○	○
		Decel.
07-19		Fan Control	0: Fan always ON	0	○	○	○	○	○
			1: 1 minute after AC motor drive stops, fan will be OFF
			2: AC motor drive runs and fan ON, AC motor drive
			stops and fan OFF
			3: Fan ON to run when preliminary heat sink
			temperature attained
			4: Fan always OFF
	07-20	Torque Command	-100.0~100.0% (Pr. 07-22 setting=100%)	0.0					○
07-21		Torque Command	0: Digital keypad	0					○
		Source	1: RS485 serial communication (RJ-11)
			2: Analog signal (Pr.03-00)
07-22		Maximum Torque	0~500%	100					○
		Command
07-23		Filter Time of Torque	0.000~1.000 sec	0.000					○
		Command
	07-24	Speed Limit Selection	0: By Pr.07-25 and Pr.07-26	0					○
			1: Frequency command source (Pr.00-20)
07-25		Torque Mode +Speed	0~120%	10					○
		Limit
07-26		Torque Mode-Speed	0~120%	10					○
		Limit

4-16 Revision August 2008, 03VE, SW V2.04