Delta Electronics VFD-VE Series manual Tension PID P2

			Chapter 4 Parameters
Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
			Setting
08-32	Tension PID P2	0.0~1000.0	50.0	○	○	○	○	○
08-33	Tension PID I2	0.00~500.00 sec	1.00	○	○	○	○	○
08-34	Reserved
08-35	PID/Line Speed Output	0: Positive output	0	○	○	○	○	○
	Status	1: Negative output
08-36	Tension/Line Speed PID	0~100.00% (according to Pr,01-00)	20.00	○	○	○	○	○
	Output Limit
08-37	Source of Line Speed	0: Disable	0	○	○	○	○	○
	Input Command	1: Analog input (Pr. 03-00~03-02 is set to 12 line speed)
		2: RS-485 communication setting (Pr.08-41)
		3: Pulse input (Pr.08-40)
		4: DFM-DCM pulse input (Pr.02-18)
08-38	Max. Line Speed	0.0~3000.0m/min	1000.0	○	○	○	○	○
08-39	Min. Line Speed	0.0~3000.0m/min	0.0	○	○	○	○	○
08-40	Pulse Number for Each	0.0~6000.0	0.0	○	○	○	○	○
	Meter
08-41	Current Line Speed	0.0~3000.0m/min	0.0	○	○	○	○	○
08-42	Source of Reel Diameter	0: Calculated by line speed	0	○	○	○	○	○
		1: Calculated by integrating thickness (encoder is on
		reel shaft)(Pr.08-49~51, Pr.10-15)
		2: Calculated by integrating thickness (encoder is on
		motor)(Pr.08-23~08-24, 08-50~08-51, 10-00~10-01)
		3: Calculated by analog input (Pr.03-00~03-02 is set to
		13)
08-43	Max. Reel Diameter	1.0~6000.0mm	6000.0	○	○	○	○	○
08-44	Empty Reel Diameter	1.0~6000.0mm	1.0	○	○	○	○	○
08-45	Source of Initial Reel	0: RS-485 communication setting (Pr.08-46)	0	○	○	○	○	○
	Diameter	1: Analog input (Pr.03-00-Pr.03-02 is set to 13)
08-46	Initial Reel Diameter	1.0~6000.0mm	1.0	○	○	○	○	○
08-47	Initial Reel Diameter 1	1.0~6000.0mm	1.0	○	○	○	○	○
08-48	Initial Reel Diameter 2	1.0~6000.0mm	1.0	○	○	○	○	○
08-49	Number of Pulse per	1~10000ppr	1	○	○	○	○	○
	Revolution
08-50	Coil Number for Each	0.001~60.000mm	1.000	○	○	○	○	○
	Layer
08-51	Material Thickness	0.001~60.000mm	1.000	○	○	○	○	○
08-52	Filter Time of Reel	0.00 to 100.00 seconds	1.00	○	○	○	○	○
	Diameter
08-53	Auto Compensation of	0: Disable	1.00	○	○	○	○	○
	Reel Diameter	1: Enable
08-54	Current Reel Diameter	1.0~6000.0mm	1.0	○	○	○	○	○
08-55	Smart Start	0: Disable	1	○	○	○	○	○
		1: Enable
		2: In unwind mode, rewind in reverse direction
08-56	Switch Level for Smart	0.0~100.0% (according to Pr.08-26)	15.0	○	○	○	○	○
	Start and PID function
08-57	Frequency for Smart Start	0.00~600.00Hz	2.00	○	○	○	○	○
08-58	Accel. Time for Smart Start	0.01~600.00 seconds	3.00	○	○	○	○
08-59	Broken Belt Detection	0: Disable	0	○	○	○	○
		1: Enable
08-60	Min. Line Speed of Broken	0.0~3000.0m/min	0.0	○	○	○	○
	Belt Detection
08-61	Allowance Error of Line	1.0~6000.0mm	100.0	○	○	○	○
	Speed of Broken Belt
	Detection
08-62	Detection Time of Broken	0.00~100.00 sec	1.00	○	○	○	○
	Belt
08-63	Allowance Error Level of	0~100%	100	○	○	○	○
	Tension/Line Speed PID
	Feedback
08-64	Allowance Error Detection	0.0~10.0 sec	0.5	○	○	○	○
	Time of Tension PID
	Feedback

Revision August 2008, 03VE, SW V2.04 4-19