Delta Electronics VFD-VE Series manual Group 10 Speed Feedback Control Parameters

Chapter 4 Parameters

Group 10 Speed Feedback Control Parameters

	Pr.	Explanation	Settings	Factory	VF	VFPG	SVC	FOCPG	TQRPG
				Setting
	10-00	Encoder Pulse	1~20000	600		○		○	○
	10-01	Encoder Input Type	0: Disable	0		○		○	○
		Setting	1: Phase A leads in a forward run command and phase
			B leads in a reverse run command
			2: Phase B leads in a forward run command and phase
			A leads in a reverse run command
			3: Phase A is a pulse input and phase B is a direction
			input. (low input=reverse direction, high input=forward
			direction)
			4: Phase A is a pulse input and phase B is a direction
			input. (low input=forward direction, high input=reverse
			direction)
			5: Single-phase input
10-02		PG Feedback Fault	0: Warn and keep operation	2		○		○	○
		Treatment	1: Warn and ramp to stop
			2: Warn and coast to stop
10-03		Detection Time for PG	0.00~10.0 sec	1.0		○		○	○
		Feedback Fault
10-04		ASR (Auto Speed	0~40	10		○		○
		Regulation) Control
		( P) 1
10-05		ASR (Auto Speed	0.000~10.000 sec	0.100		○		○
		Regulation) Control (I)
		1
10-06		ASR (Auto Speed	0~40	10		○		○
		Regulation) Control
		( P) 2
10-07		ASR (Auto Speed	0.000~10.000 sec	0.100		○		○
		Regulation) Control (I)
		2
10-08		ASR 1/ASR2 Switch	5.00~600.00Hz	7.00		○		○
		Frequency
10-09		ASR Primary Low	0.000~0.350 sec	0.008				○
		Pass Filter Gain
10-10		PG Stall Level	0~120% (0: disable)	115		○		○
10-11		PG Stall Detection	0.0~2.0 sec	0.1		○		○
		Time
10-12		PG Slip Range	0~50% (0: disable)	50		○		○
10-13		PG Slip Detection	0.0~10.0 sec	0.5		○		○
		Time
10-14		PG Stall and Slip Error	0: Warn and keep operation	2		○		○
		Treatment	1: Warn and ramp to stop
			2: Warn and coast to stop
10-15		Pulse Input Type	0: Disable	0	○	○	○	○	○
		Setting	1: Phase A leads in a forward run command and phase
			B leads in a reverse run command
			2: Phase B leads in a forward run command and phase
			A leads in a reverse run command
			3: Phase A is a pulse input and phase B is a direction
			input. (low input=reverse direction, high input=forward
			direction)
			4: Phase A is a pulse input and phase B is a direction
			input. (low input=forward direction, high input=reverse
			direction)
10-16		Output Setting for	1~255	1		○		○	○
		Frequency Division
		(denominator)
10-17		PG Electrical Gear A	1~5000	100		○		○
		(Channel 1 of PG
		card)
10-18		PG Electrical Gear B	1~5000	100		○		○
		(Channel 2 of PG
		card)
10-19		PG Position Control	0~20000	0		○		○
		Point (Home)
10-20		Range for PG Position	0~20000	10		○		○
		Attained (Home range)

Revision August 2008, 03VE, SW V2.04 4-23