Two Port 10/100 Managed Ethernet Switch with
Datasheet
14.2.5.231588 Interrupt Status and Enable Register (1588_INT_STS_EN)Offset: | 198h | Size: | 32 bits |
This read/write register contains the IEEE 1588 interrupt status and enable bits.
Writing a 1 to any of the interrupt status bits acknowledges and clears the interrupt. If enabled, these interrupt bits are cascaded into bit 29 (1588_EVNT) of the Interrupt Status Register (INT_STS). Writing a 1 to any of the interrupt enable bits will enable the corresponding interrupt as a source. Status bits will still reflect the status of the interrupt source regardless of whether the source is enabled as an interrupt in this register. Bit 29 (1588_EVNT_EN) of the Interrupt Enable Register (INT_EN) must also be set in order for an actual system level interrupt to occur. Refer to Chapter 5, "System Interrupts," on page 49 for additional information.
BITS |
|
| DESCRIPTION | TYPE | DEFAULT |
|
|
|
|
| |
31:25 | RESERVED |
| RO | - | |
|
|
|
|
|
|
24 | 1588 | Port 2 | RX Interrupt Enable (1588_PORT2_RX_EN) | R/W | 0b |
|
|
|
|
|
|
23 | 1588 | Port 2 | TX Interrupt Enable (1588_PORT2_TX_EN) | R/W | 0b |
|
|
|
|
|
|
22 | 1588 | Port 1 | RX Interrupt Enable (1588_PORT1_RX_EN) | R/W | 0b |
|
|
|
|
|
|
21 | 1588 | Port 1 | TX Interrupt Enable (1588_PORT1_TX_EN) | R/W | 0b |
|
|
|
|
| |
20 | 1588 | Port 0(Host MAC) RX Interrupt Enable (1588_MII_RX_EN) | R/W | 0b | |
|
|
|
|
| |
19 | 1588 | Port 0(Host MAC) TX Interrupt Enable (1588_MII_TX_EN) | R/W | 0b | |
|
|
|
| ||
18 | GPIO9 1588 Interrupt Enable (1588_GPIO9_EN) | R/W | 0b | ||
|
|
|
| ||
17 | GPIO8 1588 Interrupt Enable (1588_GPIO8_EN) | R/W | 0b | ||
|
|
|
|
| |
16 | 1588 | Timer Interrupt Enable (1588_TIMER_EN) | R/W | 0b | |
|
|
|
|
| |
15:9 | RESERVED |
| RO | - | |
|
|
|
|
|
|
8 | 1588 | Port 2 | RX Interrupt (1588_PORT2_RX_INT) | R/WC | 0b |
| This interrupt indicates that a packet received by Port 2 matches the |
|
| ||
| configured PTP packet and the 1588 clock was captured. |
|
| ||
|
|
|
|
|
|
7 | 1588 | Port 2 | TX Interrupt (1588_PORT2_TX_INT) | R/WC | 0b |
| This interrupt indicates that a packet transmitted by Port 2 matches the |
|
| ||
| configured PTP packet and the 1588 clock was captured. |
|
| ||
|
|
|
|
|
|
6 | 1588 | Port 1 | RX Interrupt (1588_PORT1_RX_INT) | R/WC | 0b |
| This interrupt indicates that a packet received by Port 1 matches the |
|
| ||
| configured PTP packet and the 1588 clock was captured. |
|
| ||
|
|
|
|
|
|
5 | 1588 | Port 1 | TX Interrupt (1588_PORT1_TX_INT) | R/WC | 0b |
| This interrupt indicates that a packet transmitted by Port 1 matches the |
|
| ||
| configured PTP packet and the 1588 clock was captured. |
|
| ||
|
|
|
|
| |
4 | 1588 | Port 0(Host MAC) RX Interrupt (1588_MII_RX_INT) | R/WC | 0b | |
| This interrupt indicates that a packet from the switch fabric to the Host MAC |
|
| ||
| the matches the configured PTP packet and the 1588 clock was captured. |
|
| ||
| Note: | For Port 0, receive is defined as data from the switch fabric, while |
|
| |
|
| transmit is to the switch fabric. |
|
| |
|
|
|
|
|
|
SMSC LAN9311/LAN9311i | 227 | Revision 1.4 |
| DATASHEET |
|