
FATAL ENTRY TYPE CANNOT | An invalid Entry Type has been  | UNIT MAY NEED TO BE  | 
CONTINUE CYCLE POWER | detected in your program. Cycle power  | RESET TO CLEAR ERROR –  | 
  | & see if it clears the error. This can be  | RESET PROGRAMS & DATA  | 
  | caused by the TriCoder turning off  | IN SYSTEM SETUP & RESET  | 
  | during programming.  | SETUPS TO DEFAULT - Call  | 
  | 
  | for support if condition  | 
  | 
  | continues.  | 
FATAL PROMPT #. CYCLE POWER_
An invalid Prompt Number was UNIT MAY NEED TO BE detected. Cycle Power and see what RESET TO CLEAR ERROR –
happens. The Program was not RESET PROGRAMS & DATA completed before turning the unit off, or IN SYSTEM SETUP & RESET the memory is not reset after a SETUPS TO DEFAULT - Call
firmware update.for support if condition continues.
FILE USED BY Pn  | You have selected a data file # with data  | HIT ANY KEY. Select another  | |
HIT ANY KEY_  | in it, collected by another program.   | data file #.  | 
  | 
  | Select another data file #.  | 
  | 
  | 
IDENTIFIER ERROR  | You have entered data that doesn‟t  | ||
HIT ANY KEY_  | match the DATA ID specified.  | the DATA ID.  | 
  | 
PROGRAM n INCOMPLETE  | Unit was shut off or went to sleep  | Check program  | for errors.  | 
HIT ANY KEY_  | during programming.  | UNIT MAY NEED TO BE  | |
  | 
  | RESET TO CLEAR ERROR –  | |
  | 
  | RESET PROGRAMS & DATA  | |
  | 
  | IN SYSTEM SETUP & RESET  | |
  | 
  | SETUPS TO DEFAULT - Call  | |
  | 
  | for support if  | condition  | 
  | 
  | continues  | 
  | 
INVALID DATA LENGTH  | You have tried to enter 00 for Max Data  | HIT ANY KEY.   | |
HIT ANY KEY_  | Length. Entry must be at least 01.  | length.  | 
  | 
INVALID INPUT DEVICE  | You have specified a character other  | HIT ANY KEY. Enter a valid  | |
HIT ANY KEY_  | than K W or ENTER for the INPUT character.  | 
  | |
  | DEVICE.  | 
  | 
  | 
INVALID FILE #  | You have entered a character other  | HIT ANY KEY. Enter a valid  | |
HIT ANY KEY_  | than 0,1,2,or 3 at the Data File No. number.  | 
  | |
  | Prompt.  | 
  | 
  | 
INVALID HEADER  | The Header Record in a table has an  | Check header record, fix and  | |
HIT ANY KEY_  | invalid format.  | retry.  | 
  | 
INVALID PASSWORD  | You have not entered the correct  | HIT ANY KEY. Enter the  | |
HIT ANY KEY_  | password.  | correct password - WDTRI.  | |
INVALID PROGRAM #  | You have entered something other than  | HIT ANY KEY. Enter the  | |
HIT ANY KEY_  | 0,1,2, or 3 in Programming Mode or  | correct number.  | 
  | 
  | 1,2, or 3 for Data Collection Mode  | 
  | 
  | 
ITEM NOT FOUND n  | An item entered in the TriCoder has not  | HIT ANY KEY. Enter another  | |
HIT ANY KEY_  | been found in table n.  | item number or check table  | |
  | 
  | data.  | 
  | 
NONPORTABLE MODE PRESS <F1> TO EXIT
You are operating in Non Portable Continue to enter data. Press mode - the TriCoder transmits data F1 to get to Mode Menu. immediately to the host computer
without saving in memory.
OUT OF MEMORY  | You have filled the memory and must  | HIT ANY KEY. Upload data  | ||
HIT ANY KEY_  | upload before you can collect any more  | and  | continue  | with data  | 
  | data.  | collection.  | 
  | |
PLEASE ENTER  | TriCoder is in diagnostic mode, waiting  | Enter  | the correct  | diagnostic  | 
DIAG COMMAND_ | for a command.  | code or press F1 to exit.  | ||
Possible Data Loss  | Slight memory error. Cycling Power on  | UNIT MAY NEED TO BE  | ||
Press Any Key_ | the TriCoder may fix the problem.  | RESET TO CLEAR ERROR –  | ||
  | Watch TriCoder closely. Can occur  | RESET PROGRAMS & DATA  | ||
  | after removing the battery  | IN SYSTEM SETUP & RESET  | ||
  | 
  | SETUPS TO DEFAULT - Call  | ||
  | 
  | for  | support if  | condition  | 
  | 
  | continues.  | 
  | |
PROGRAM n INCOMPLETE HIT ANY KEY_
Unit was shut off or went to sleep Check program for errors. during programming or the program is UNIT MAY NEED TO BE
bad.RESET TO CLEAR ERROR –
RESET PROGRAMS & DATA
IN SYSTEM SETUP & RESET
SETUPS TO DEFAULT - Call for support if condition continues
PROGRAMMING MODE  | Do you want to write, edit, review or  | Press 4 at the Main Menu for  | |
  | delete a program?  | PROGRAMMING MODE.  | |
PROGRAM NO.?  | You are in Data Collection mode and  | Key 0, 1,2 or 3.  | |
KEY   | need to select a program to use.  | 
  | |
SEARCH PATTERN | The SEARCH key was pressed.  | Enter data to search for or  | |
_  | 
  | press ENTER key to exit.  | |
Start Host USB  | Firmware download has been Start the Windows program,  | ||
Firmware Download  | requested. USB enumeration has been TriCoder Firmware  | ||
Program First and | completed. Now TriCoder is requesting  | Downloader. Available on  | |
the user to start PC TriCoder Firmware  | Utilities   | ||
Then Hit Any Key.  | |||
Downloader.  | www.barcodehq.com.  | ||
  | |||
84