Host Port Zoning Anonymous Access | APC 15000 RAID instruction

Controller Installation

2.3.9.2Host Port Zoning (Anonymous Access)

Host Port Zoning (Anonymous Access) should only be used for non-SAN environment. Users are given “general admission” to the data.

Anonymous Access (host port zoning) provides only the minimum level of

!security.

Warning

One zoning configuration is supported for each of the host ports. Any unauthorized user accessing the storage is considered “anonymous” and granted zoning access for the host port to which they are connected. Given below is an example for adding LUN zoning to host port 1. External LUN 1 is mapped to internal LUN 0 and it is read-only for the users.

1.To edit the default zoning on a host port, type: zoning edit<Enter>. The current settings are displayed.

2.Select a host port (1..4): 1<Enter>

3.Specify the internal LUN (0..1023) to be mapped to the external LUN. The new settings will display

.

4.Repeat steps 1–3 to configure other host ports.

007-5510-002

27

Image 41

APC 15000 RAID manual Host Port Zoning Anonymous Access

Contents

SGI InfiniteStorage 15000 RAID User’s Guide Copyright Introduction Controller Remote Management and Troubleshooting Drive Enclosure Operation 115 Replacing the DEM 127 Preface What is in this guideInternational Standards Potential for Radio Frequency Interference Safe Handling European RegulationsQualified Personnel Chassis Warning Label Weight Hazard Safety PCM Warning Label Power Hazards Recycling of Waste Electrical and Electronic Equipment Weee Rack System Precautions Cover Label ESD Precautions Data Security Preface Page Introduction Controller FeaturesSimplifies Deployment of Complex SANs Infiniband or Fibre Channel FC-8 Connectivity Throughput Controller Hardware 1SGI InfiniteStorage 15000 IB Front and Rear Views 2Fan Module front panel Power Supply and Fan Modules Host IB LEDs Ethernet 2 I/O Connectors and Status LED Indicators 4Host Port LEDs Ctrl Temp FAN Status System Disk Status Indicator Led Activity Explanation Uninterruptible Power Supply UPS Page Setting Up the Controller Controller Installation Rack-Mounting the Controller Chassis Connecting the Controller in Dual ModeUnpacking the System Disk ports Host port 1 Host port Connecting the Controller Basic Key Operations Connecting the RS-232 Terminal Basic Key Assignments Powering On the Controller Planning Your Setup and Configuration Configuring the Controller Setting System Time & Date Configuration InterfaceLogin as Administrator 4Tier Changemap Screen Setting Tier Mapping Mode 5Tier Status Screen Checking Tier Status and Configuration Heading Definitions Cache Coherency and Labeling in Dual Mode 7Dual Controller Configuration Configuring the Storage Arrays Enter the block size in Bytes 512Enter To create the LUN 1, type Authorized user Host port zoning Setting Security LevelsUser Authentication Recommended for SAN Environment To add a user Check to ensure that the LUN Zoning chart is empty Figure 12shows a finished sample Host Port Zoning Anonymous Access Page Management Interface Controller ManagementManaging the Controller Login Available CommandsAdministrator and User Logins Who Am PasswordLogout Configure and Monitor Status of Host Ports Configuration Management Host Status Host ID Host Port Speed Configure and Monitor Status of Storage AssetsHost IB Users Disk STATUSCLEAR=tierchannel resets the channel error counts 11Disk Defect List Screen Sata Aamux PHY Errors 12Disk PLS Tier 1 Status Screen Tier View Tier Configuration LUN View 14Tier Configuration ALL Screen Adding/Removing Storage Assets LUN ConfigurationLUN Reservations Tier Mapping for Enclosures Telnet System Network Configuration API Server Connections Snmp & Syslog System Restart Restarting the ControllerDisplaying and Editing the Routing Table System Date Setting the System’s Date and TimeSystem Shutdown System Time Saving the Controller’s ConfigurationRestoring the System’s Default Configuration Creating a LUN Configuring the Storage ArrayLUN Management Changing a LUN Label Formatting a LUNInterrupting a LUN Format Operation Deleting a LUN Moving a LUN Dual Mode OnlyAutomatic Drive Rebuild Manual Drive Rebuild Smart CommandDrive Rebuild Verify Manual Drive Replace Smart Enable Cache Coherent Couplet Controller Configuration Cache/Non-Cache Coherent Labeling the Controller Units Fail / Restore the Other Controller Unit in the Couplet Pair Singlet Performance ManagementOptimizing I/O Request Patterns Cache Segment Size Writeback Cache SettingsPrefetch Settings Disk Configuration Settings Cache Settings Reset 31Current Audio/Visual Settings Audio/Visual Settings of the System Initial Cache Locking LUN in Cache System Performance Statistics Locking / Unlocking a LUN 33System Performance Statistics Screen 34Command Delay Statistics Screen 35Host Delay Statistics Screen 37Host Command Offsets Screen 38Dual Message Statistics Screen Background Format/Rebuild Operations Resources Allocation Background Tier Verify Operations Background LUN Verify Operations 42Tier Verify on Screen Rebuild Journaling CLI commands Tier PAUSE, Tier RESUME, Tier Stop 007-5510-002 SES Device Monitoring Rate 44Sample Tier Journal Command Screen Host Command Timeout Security Administration Zoning Anonymous Access Monitoring User Logins 50Edit Zoning Configuration Screen User Authentication Displaying Current Firmware Version Firmware Update ManagementFirmware Update Procedure 53Downloading Controller Firmware Remote Login Management 54Telnet Statistics When a Telnet Session is Active 56Telnet Session Information Message Log System and Drive Enclosure FaultsSystem Logs Saving a Comment to the Log Displaying System Uptime APC UPS Snmp Trap Monitor Other UtilitiesAPI Server Connections Changing Baud Rate for the CLI Interface Disk Diagnostics 4 CLI/Telnet Session Control Settings Spare Commands Disk Reassignment and Miscellaneous Disk Commands Unique Network Interface Set Up Controller Remote Management and TroubleshootingRemote Management of the Controller Network Connection Network trapip=computer’s IP address 3Current Controller Routing Table Login Names and Passwords Sdd.mib Sddtrap.mib Snmp Set Up on Host ComputerController Implementation of Snmp Component Failure Recovery Troubleshooting the ControllerPower Supply Failure Traps Fan Failure Recovering from Drive Failures Single Drive Failures Manually Replacing a Failed Disk with Spare Disk Returning the System to a Fault-Tolerant State Multiple Drive and Channel Failures Changing the Rate of RebuildInterrupting the Rebuild Operation 7Example of SES Message Component Failure on Enclosures SGI InfiniteStorage 15000 Drive Enclosure Drive Enclosure System 3Drive Enclosure Module Locations Enclosure Core Product Enclosure Chassis Power Cooling Module PCMPlug-in Modules Input/Output I/O Module Color Definition Enclosure Audible AlarmGreen Amber Blue Drive Carrier Module and Status IndicatorDEM Card Front Panel Drive Activity Indicators Indicators System Power System FaultDEM Fault Shelf Identify Numbered Drive FaultIndividually HDDs Rear of Enclosure Activity Indicators Internal Indicators Dimensions Visible and Audible AlarmsDrive Enclosure Technical Specification Input Parameter Value Weight Environment PCM Safety and EMC CompliancePower Cord Page Introduction Planning Your Installation Drive Enclosure Installation Enclosure Bay Numbering Convention Bay B Bay a 21X60 Drive Numbering Table Controller Options Enclosure Installation ProceduresI/O Module Configurations Grounding Checks Sata Interposer FeaturesDrive Enclosure Device Addressing Page Drive Enclosure Operation Power On / Power DownBefore You Begin PCM LEDs Definition 2 I/O Panel LEDs Overview Drive Enclosure TroubleshootingInitial Start-up Problems LEDs PCM Power Cooling ModuleHDD Hard Disk Drive DEM Drive Expander Module Blue 4 I/O Module Definition Normal Behavior Troubleshooting Audible AlarmSES Command Top Cover Open Symptom Cause Action Thermal Shutdown Dealing with Hardware FaultsThermal Alarm Power Cooling Modules Continuous Operation During ReplacementReplacing a Module Module To remove an AC PCM Thumb Screw Model To install an AC PCM Handle ModelTo install an AC PCM Thumbscrew Model 2 I/O Module To installing the I/O ModuleReplacing the Drive Carrier Module To remove the I/O Module To Insert the Drive Carrier Module Replacing the DEMPage Reliability Configuration, Performance, & Capacity Physical, Power & Environmental Drive Addressing 007-5510-002 133 Page Cabling Controllers and Drive Enclosures 136 137 138