| 22.0 | Programming Sheets |
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Location |
|
|
|
|
| Options/Notes |
|
|
|
|
| Default/ |
| |||||||||
| Function |
|
|
|
|
|
|
|
| Programming Entry |
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
| 267 to 322 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| Zone Definitions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| Refer to page 54 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 0 0 1 14 1 1 |
|
|
|
|
|
| 12 0 0 1 12 1 1 |
| |||||||
| Zone #01 |
|
| (Delay 1) |
| Zone #05 | (Fixed | ||||||||||||||||
| (267 to 273) |
|
|
|
|
|
|
|
|
| (295 to 301) |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 0 0 1 14 1 1 |
|
|
|
|
|
| 12 0 0 1 12 1 1 |
| |||||||
| Zone #02 |
| (Handover) |
| Zone #06 | (Fixed | |||||||||||||||||
| (274 to 280) |
|
|
|
|
|
|
|
|
| (302 to 308) |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 0 0 1 14 1 1 |
|
|
|
|
|
| 13 0 0 1 12 1 1 |
| |||||||
| Zone #03 |
| (Handover) |
| Zone #07 |
| (Fixed | ||||||||||||||||
| (281 to 287) |
|
|
|
|
|
|
|
|
| (309 to 315) |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 0 0 1 14 1 1 |
|
|
|
|
|
| 9 0 0 1 12 1 1 |
| |||||||
| Zone #04 |
|
| (Instant) |
| Zone #08 |
|
| (Fixed Tamper) | ||||||||||||||
| (288 to 294) |
|
|
|
|
|
|
|
|
| (316 to 322) |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The first location (from the left) of the zone definition is the Zone Type. The options are: |
| ||||||
0 | Instant | 4 | Reserved | 8 | 12 | ||
1 | Handover | 5 | Reserved | 9 | 13 | ||
2 | Delay 1 | 6 | 10 | Reserved | 14 | Chime | |
3 | Delay 2 | 7 | 11 | Keyswitch | 15 | Not used | |
The second location of the zone definition is the Zone Pulse Count. Use the pulse count to program the number of pulses (0 to 15) that must register within the pulse count time to activate an alarm.
The third location (from the left) of the zone definition is the Zone Pulse Count Time. The options are:
| 20 ms Loop Response Time: |
| 150 ms Loop Response Time: | ||||
0 | 0.5 sec | 4 | 4 sec | 8 | 20 sec | 12 | 60 sec |
1 | 1 sec | 5 | 5 sec | 9 | 30 sec | 13 | 90 sec |
2 | 2 sec | 6 | 10 sec | 10 | 40 sec | 14 | 120 sec |
3 | 3 sec | 7 | 15 sec | 11 | 50 sec | 15 | 200 sec |
The fourth location of the zone definition is the Zone Options 1 parameter. The options are:
1 | Lockout siren/dialer | 4 | Silent alarm |
2 | Delay Alarm Report | 8 | Sensor watch |
The fifth location of the zone definition is the Zone Options 2 parameter. The options are:
1 | Isolated in STAY Mode 1 | 4 | Forced arming allowed |
2 | Zone isolation allowed | 8 | Zone Restore Report allowed |
The sixth location of the zone definition is the Report Code. The options are:
0Do not send Zone Alarm Reports
1 Send Zone Alarm Reports
The seventh location of the zone definition is the Zone Dialer Options parameter. The options are:
0 | No Zone Reports allowed | 4 | Report to both Receiver 1 and Receiver 2 |
1 | Report to Receiver 1 | 8 | Report to Receiver 2 only if Receiver 1 |
2 | Report to Receiver 2 |
| fails |
The keyswitch zone options replace Zone Options 1 for zones programmed to operate as keyswitch | |||
zones (Zone Type = 11). The options are: |
|
| |
0 | Latching arm and disarm in AWAY Mode | 8 | Momentary arm and disarm in AWAY |
1 | Latching arm in AWAY Mode |
| Mode |
2 | Latching disarm from AWAY Mode or | 9 | Momentary arm In AWAY Mode |
| STAY Mode | 10 | Momentary disarm from AWAY Mode or |
4 | Latching arm and disarm in STAY Mode |
| STAY Mode |
5 | Latching arm in STAY Mode | 12 | Momentary arm and disarm in STAY Mode |
6 | Latching disarm from STAY Mode | 13 | Momentary arm in STAY Mode |
|
| 14 | Momentary disarm from STAY Mode |
88
