ICP-CC404 Installation Guide 6.0 System Functions
3.Press any of the [TRANSMIT] buttons on the
Two beeps sound and the STAY and AWAY indicators turn off.
4.Repeat this procedure to change other remote radio User Codes.
This function ends automatically if you do not press a button within 60 sec or if you press [AWAY].
One long beep indicates that the code already exists or that you entered an incorrect user number.
To delete a remote radio User Code:
1.Enter your Master Code and press [1][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
2.Enter the number of the code (9 to 16) you want to delete and press [AWAY].
Two beeps sound and the corresponding codepad indicators light. Refer to Table 26.
3.Press [STAY] to delete the User Code.
Two beeps sound and the STAY and AWAY indicators turn off.
4.Repeat this procedure to delete other remote radio User Codes.
This function ends automatically if you do not press a button within 60 sec or if you press [AWAY].
One long beep indicates that the code already exists or that you entered an incorrect user number.
6.2.3Changing Domestic Phone Numbers
When the system is set up for domestic dialing, this function allows the installer to view and program the telephone numbers that the system calls if an alarm occurs. Refer to Section 9.0 Domestic Dialing on page 40 for more information.
To change domestic phone numbers:
1.Enter your Master Code and press [2][AWAY]. Three beeps sound and the STAY and AWAY indicators flash.
If there are telephone numbers programmed, they appear one digit at a time using the remote codepad indicators. Refer to Table 27 for the indicators and their meanings.
If there are no telephone numbers programmed, an additional two beeps sound after entering this mode. These two beeps normally sound after you enter the last digit of the last phone number.
Table 27: Codepad Indicators When Changing Domestic Telephone Numbers
|
|
| Zone Indicators |
|
| MAINS | |||
Digit | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | Indicator |
0 |
|
|
|
|
|
|
|
| X |
|
|
|
|
|
|
|
|
|
|
1X
2
X
3 | X |
4
X
5 | X |
6
X
7 | X |
8
X
9 | X | X | ||||
* | X |
|
|
|
| X |
# |
| X |
| X | ||
Pause |
|
| X |
|
| X |
Break |
|
|
| X |
| X |
2.Enter the first phone number.
The indicator for each digit lights as you enter it.
3.If you are programming another phone number, press [STAY][4] to separate the end of one phone number and the beginning of the next.
If you are not programming other numbers, go to Step 5.
4.Repeat Steps 2 and 3 to program another phone number.
5.Press [AWAY] to exit from this mode.
Table 28: Domestic Dialing Digits
|
|
|
|
Digit | Number to | Digit | Number to |
Required | Program | Required | Program |
0 | 0 | 7 | 7 |
1 | 1 | 8 | 8 |
|
|
|
|
2 | 2 | 9 | 9 |
3 | 3 | * | * 1 |
|
|
|
|
4 | 4 | # | * 2 |
5 | 5 | 4 sec pause | * 3 |
6 | 6 | break | * 4 |
Example
If you want to program two separate telephone numbers (9672 1777 and 9672 1233), enter:
[2 5 8 0 2][AWAY][9 6 7 2 1 7 7 7][STAY]
[4 9 6 7 2 1 2 3 3][[AWAY]
To disable domestic dialing:
Enter your Master Code and press [2][AWAY] [STAY][4][AWAY].
Bosch Security Systems, Inc. 12/08 | 33 |
