Carrier 30XW150-400 specifications 130, Service Configuration Tables

APPENDIX C — CCN TABLES (cont)

SERVICE CONFIGURATION TABLES

TABLE	DISPLAY NAME	RANGE	DEFAULT	UNITS	POINT NAME	WRITE
						STATUS
TABLE USED FOR DISABLE COMPRESSORS (see notes)
CP_UNABL	Compressor A Disable	No/Yes	No		un_cp_a
(See Notes)	Compressor B Disable	No/Yes	No		un_cp_b
	Compressor C Disable	No/Yes	No		un_cp_c
FACTORY	Unit Type	1 (Cooling Only)	1		unit_typ
(See Notes)		2 (Heat Pump)*
		3 (Water Cooled)
		4 (Heat Machine)
	Unit Capacity	0 to 1800	Nominal Unit Size		unitsize
	Power Frequence 60HZ Sel	Yes/No	Yes		freq_60H
	Power Supply Voltage	200 to 660	460	volts	voltage
	NB Fans on Varifan Cir A	0 to 6	1		varfan_a
	NB Fans on Varifan Cir B	0 to 6	1		varfan_b
	NB Fans on Varifan Cir C	0 to 6	0		varfan_c
	Soft Starter Select	Yes/No	No		softstar
	Wye Delta Start Select	Yes/No	No		wye_delt
	Air Cooled Reclaim Sel	Yes/No	No		recl_opt
	Free Cooling Select	Yes/No	No		freecool
	Cooler Heater Select	Yes/No	Yes		heat_sel
	Condenser Water Val Sel*	Yes/No	No		cond_val
	Hot Gas Bypass Select	Yes/No	No		hgbp_sel
	MCHX Exchanger Select	Yes/No	Yes		mchx_sel
	Boiler Command Select	Yes/No	No		boil_sel
	Energy Management Module	Yes/No	No		emm_nrcp
	High Tiers Display Selec	No = Use Navigator™	No		highdisp
		display as user interface
		(factory installed)
		Yes = Use Touch Pilot™
		Display as user interface
		(factory installed)
	Factory Password	0 to 9999	111		fac_pass
	Hydraulic Transducer Kit	Yes/No	No		kithydro
	Cooler Pass Number	1 to 3	2		cpass_nb
	VLT Fan Drive Select*		0		vlt_sel
	VLT Fan Drive rpm*		0		vlt_rpm
	High Condensing Select	Yes/No	No		highcond
	Max Condenser LWT=45degC	Yes/No	No		max_clwt
FACTORY2	Compressor A Config
	Must Trip Amps	0 to 600	Refer to Appendix D		cpa_mtac
	S1 Config Switch (8 to 1)	00000000 (8 position dip	Refer to Appendix D		cpa_s1_c
	Compressor B Config	switch configuration)
	Must Trip Amps	0 to 600	Refer to Appendix D		cpb_mtac
	S1 Config Switch (8 to 1)	00000000 (8 position dip	Refer to Appendix D		cpb_s1_c
	Compressor C Config	switch configuration)
	Must Trip Amps	0 to 600	0		cpc_mtac
	S1 Config Switch (8 to 1)	00000000 (8 position dip	0		cpc_s1_c
		switch configuration)
	Circuit A Total Fans NB	2 to 8	0		nb_fan_a
	Circuit B Total Fans NB	2 to 8	0		nb_fan_b
	Circuit C Total Fans NB	0 to 8	0		nb_fan_c
	EXV A Maximum Steps Numb	0/15000	4260		exva_max
	EXV B Maximum Steps Numb	0/15000	4260		exvb_max
	EXV C Maximum Steps Numb	0/15000	0		exvc_max
	Economizer A Steps Numb	0/15000	2785†		eco_cnfa
	Economizer B Steps Numb	0/15000	2785†		eco_cnfb
	Economizer C Steps Numb	0/15000	0		eco_cnfc

*Not supported.

†0 = No economizer.

NOTES:

1.Table used to disable compressors for maintenance purposes. The capacity control will consider that these compressors (once set to YES) are failed manually (no alarm will appear).

2.Enter unit size. This item allows the controls to determine capacity of each compressor and the total number of fans on each circuit based on a com- pressor arrangement array (can be viewed in table FACTORY2). It is not necessary to enter compressor capacity and number of fans on each cir- cuit. See the 30XW Installation Instructions for more information.

3.Number of fans controlled directly by a variable speed fan actuator using 0 to 10 vdc signal. This will enable the controls to determine the remaining discrete fan staging outputs from the total fans on each circuit.

4.Used for extra functions with the purpose of energy management such as occupancy override switch, ice storage, setpoint reset, and demand limit.

5.Compressor capacity will be automatically determined if unit size entered in FACTORY table matches the values in the unit compressor configura- tion table.

6.Total number of fans includes fans controlled by a variable speed fan. This value will be automatically populated if unit size entered in FACTORY table matches the values in the unit compressor configuration table.

130