Manuals / Compex Systems / Computer Equipment / Network Router

Compex Systems WPE53G manual Step

Models: WPE53G

1 184

Download 184 pages 14.43 Kb

<>

FAQ Signal Strength Password Administer the System Wireless Routing Client Mode Access with uConfig Backup or Reset the Settings Access Point Mode Setup Requirements ACK Timeout

Page 78

Step 5:

MAC Filter Address List page displays with updated MAC Address List.

NOTE

Please reboot to effect all changes and new MAC address entries.

Page 72

Page 77 Page 79

Image 78

Compex Systems WPE53G manual Step

Page 77 Page 79

Related pages How do I access the Rosemount 2088 manual?

Contents

Page FCC Notice Firmware This manual is written based on Firmware version Table of Contents 106 Administer the System Overview the Product Introduction Features and Benefits Multiple-SSID Supporting Vlan Segmentation RIP 1 When to Use Which Mode Access Point Mode Access Point Client Mode Wireless Routing Client Mode Gateway Mode Static IP Address Dynamic IP AddressPPP over Ethernet PPPoE Wireless Adapter Mode Transparent Client Mode Point-to-Point Point-to-MultiPoint Transparent Client Mode Repeater Mode Panel Views and Description Setup Requirements Using power adapter to supply power to the unit Step Step Step Setup for Windows XP/2000 PropertiesSelect the Use the following Click on the OK button to close all windows Access the Web Interface Access with uConfig Step Step Manual access with Internet Explorer Step Setup Management Port Select to Automatically obtain IP address Click on the Apply button to save your new parameters DNS Select to Use the following IP address 192.168.168.1 Setup Dhcp Server Set Dhcp Mode to None Set Dhcp Mode to Dhcp Server 192.168.168.100 Dhcp Set Dhcp Mode to Dhcp Relay Parameters Description Select Management Setup from the Configuration menu View Active Dhcp LeasesLease Expired Time Reserve IP Addresses for Predetermined Dhcp Clients Step Delete Dhcp Server Reservation Setup Wlan Configure the Basic Setup of the Wireless ModePage Current Mode Site Survey 802.11b/g mixed Wireless Profile Country Channel Tx Rate Closed System802.11b only 802.11g only Act as RootAP Channel Survey Scan for Site Survey Bssid Auth View Link Information Signal Strength StateCurrent Channel Scan for Channel Survey Click on the Refresh button to update the screen MyQuality APCount Align the Antenna Between 13 Between 19Between 17 Below Configure the Advanced Setup Wireless Mode Advanced Setup Parameters View the Statistics Setup Your WAN Page Setup your WAN for Adsl Internet using PPP over Ethernet Page Click the MTU Button in Advanced WAN Options Page Page Setup Telnet / SSH Page Access the Telnet Command Line Interface Access the Secure Shell Host Command Line Interface Set the WEB Mode Use MAC Filtering Select MAC Filtering from Wlan Setup Add a MAC Address to the MAC Address List MAC Filter Address List page displays Click the Add button Step Delete a MAC Address from All Access Points Select View Complete MAC ListPage Delete a MAC Address from Individual Access Point Page Edit MAC Address from the MAC Address List Page Perform Advanced Configuration Setup Routing Configure Static Routing Select to Enable RIP Status Use Routing Information Protocol Use Network Address Translation Configure Virtual Servers Based on DMZ Host Select NAT from the Configuration command menuNAT Options Configure Virtual Servers Based on Port Forwarding Click the Port Forwarding button in Advanced NAT OptionsPage Known Server Custom ServerPage Configure Virtual Servers based on IP Forwarding Advanced NAT Options Enable Bandwidth Control Control the Bandwidth Available Configure WAN Bandwidth Control Enter the Download Total Rate and Upload Total Rate Configure LAN Bandwidth Control Ceiling Rate kbit Committed RateKbit Rule Type Setup Remote Management Select Remote Management from Configuration command menuPerform Remote Management Use Parallel Broadband Enable Parallel Broadband Setup Email Notification Click on the Email Notification button Using Static Address Translation Use DNS Redirection Page Enable or Disable DNS Redirection Select to Enable or Disable Dynamic DNS Setup To enable/disable Dynamic DNS Setup Choice To manage Dynamic DNS ListChoice Ddns Provider page appears Provider Name Enter your Ddns account Username and Password Select Backup Mail Exchanger to enable this service Enter your DtDNS account Username and Password Use the Wireless Extended Features Setup WDS2 Ensure that The Current Mode is set to Access Point Select Act as RootAP Follow these settings to setup access point Configure WDS2 link Set Virtual AP Multiple Ssid Virtual AP Select Virtual AP Set Preferred APs Preferred APs Get Long Distance Parameters Outdoor ACK TimeoutCTS Timeout Distance Set Wireless Multimedia Select to Enable Wireless Multimedia WMM WMM Parameters for advanced users Setup Point-to-Point & Point-to MultiPoint Connection RootAP Step Ensure that The Current Mode is set to Transparent Client Enter the Remote AP MAC Setup Repeater Page Follow these settings to setup the root AP Ensure that The Current Mode is set to Repeater Enter the Remote Essid Secure your Wireless LAN Use Hexadecimal Use Ascii Setup WEPKey Bit WEP Setup WPA-Personal At the WPA1/2-PSK SetupPassphrase Alphanumeric characters Hexadecimal Enter the GTK Group Transient Key Updates Set the Cipher Type to TkipSet the Cipher Type to AES Setup 802.1x/RADIUS for Access Point Bit 128-bit Setup 802.1x/RADIUS for Client If using EAP-PEAP802.1x EAP Type Setup WPA Enterprise for Access Point At the WPA1/2-Enterprise AP Setup Setup WPA Enterprise for Client At the WPA1/2-Enterprise Client Setup For WPA-Enterprise For WPA2- EnterpriseFor WPA- Enterprise -AUTO If using EAP-PEAPWPA EAP Type Configure Packet Filtering Use Packet Filtering ƒ Any day Filtering Configuration table will then be updated ƒ Any time Configure URL Filtering Use URL FilteringChange button Configure the Firewall Configure SPI Firewall Description PolicyTypes Packet Type Source Source IPDestinatio PortPage Use the Firewall Log View Firewall Logs Use the System Tools Use the Ping Utility Use Syslog Enter the Logging IP or Domain Name Enter the Logging Port Page Setup System Clock Select System Clock Setup from the System Tools menu Upgrade the Firmware with uConfig Select Firmware Upgrade from the System Tools menu Step Upgrade the Firmware with Command Line Interface Set upgrade IP address of AP firmware image filename Perform Firmware Recovery Access Point State Diagnostic LED \accesspoint\TFTP -i 192.168.168.1 PUT accesspointxxx.img Backup or Reset the Settings Reset your settingsSelect Backup or Reset Settings from the System Tools menu Backup your Settings Restore your Settings Reboot the System Select Reboot System from the System Tools menu Change the Password Select Change Password from the System Tools menuEnter the New Password field and then Confirm Password To Logout Use the Help menu View About System Get Technical Support Click on Get Technical Support from the Help menu Appendix Use the Command Line Interface Syntax Ctrykuwait Ctrylatvia Ctrylebanon CTRYLIECHTENSTEIN, LI Ssid Syntax Description Custom Configuration Update FAQ Page Page Page Appendix View the Technical Specifications Firmware Upgrade Technical Support Information Technical Support Centres

Top Page Image Contents