Environmental specifications, 125 | Gateway 960 instruction

Environmental specifications

Environmental specifications

The following specifications identify maximum environmental conditions. At no time should the server run under conditions which violate these specifications.

Variable	Requirements
Temperature	Maximum rate of change: 18°F (10°C) per hour
	Nonoperating: -55° to 150°F (-48.3° to 65.5°C)
	Operating: 41° to 95°F (5° to 35°C); derated 0.9°F (0.5°C) for every
	1,000 feet (305 meters)

Altitude

Humidity

10,000 feet (3,048 meters) maximum

Operating wet bulb: Not to exceed 91.4°F (33 °C) (with diskette drive or hard drive)

Nonoperating: 95% relative (noncondensing) at 86° F (30° C)

Shock	Operating: 2.0 g, 11 msec, ½ sine
	Packaged: Operational after 30-inch free fall (cosmetic damage might
	occur)
AC input power	100-240 V, 8.0 A, 50/60 Hz

www.gateway.com

125

Image 131

Gateway 960 manual Environmental specifications, 125, Variable Requirements

Contents

Page Page Contents Troubleshooting Installing Components 135 Iii121 131Page Checking Out Your GatewayServer Front Front Back Interior Left side System board System board Right side Gateway Web site Getting HelpServer Companion CD Online help Setting UpServerYour Converting to a rackmount server Setting up the hardware Surge protectors Protecting from power source problems Line conditioners Uninterruptible power supplies To start the server Starting your server When the power It means Indicator is Understanding the power-on self-testTo select which device your your server boots from To turn off the server Turning off your server To restart your server Restarting rebooting your serverTo close unresponsive programs in Windows 2000 Server Setting up the operating system Setting Up Your Server MaintainingServerYour Caring for your server Weekly Maintenance task Protecting your server from viruses To check hard drive space in Windows 2000 Server Managing hard drive spaceChecking hard drive space To check the hard drive for errors in Windows 2000 Server Using Disk CleanupChecking the hard drive for errors To use Disk Cleanup in Windows 2000 Server Click the Tools tab To defragment a hard drive in Windows 2000 Server Defragmenting the hard drive Backing up files Cleaning the exterior Cleaning your server Cleaning the tape drive Cleaning the keyboardCleaning the screen To clean your trackball mouse Cleaning the mouse Mouse rollers To create startup diskettes in Windows 2000 Server Preparing for system recoveryCreating startup diskettes Creating an emergency repair diskette Preparing for system recovery Maintaining Your Server To record your Bios configuration Keeping a record of system configuration Server security System administrationTo set the Bios security passwords ManageX Event Manager Option Description To view the event log Using your Server Companion CD ComponentsInstalling Gathering the tools you need Preparing to install componentsSelecting a place to work Preventing static electricity discharge To open the server case Opening the server case Opening the server case Installing Components To close the server case Closing the server case Installing Components Installing drives To install a 5.25-inch drive Installing a media drive Installing drives Hard drive screws Go to Step Installing Components Screw Follow the instructions in Closing the server case on To install a hard drive Installing a hard drive Screw Installing drives Installing memory To install or replace memory PCI slot Description Installing PCI expansion cards To replace, add, or reseat a PCI expansion card Release lever Card retention cover Installing PCI expansion cards Follow the instructions in Closing the server case on To replace a processor Installing a processor Installing Components Installing a processor Processor 1 fan connector Processor 2 fan connector Installing a voltage regulator To replace the power supply Replacing the power supply Replacing the power supply Follow the instructions in Closing the server case on To replace the Scsi backplane Replacing the Scsi backplane Slide the hot-swap cage out about two inches from the case Replacing the Scsi backplane Thumbscrew Replacing the Scsi backplane Follow the instructions in Closing the server case on To replace the system board Replacing the system board System board tray thumbscrew Replacing the system board To replace a fan Replacing a fan Replacing a fan To replace the battery Replacing the Cmos battery Replacing the Cmos battery Installing Components Using the Bios Setup Utility To open the Bios Setup utility Opening the Bios Setup utility To recover the old Bios Updating the BiosRecovering the Bios To update the Bios To reset the Bios Resetting the Bios Resetting Bios passwords Using the Bios Setup Utility Troubleshooting Safety guidelines Error messages Invalid configuration information Error loading operating systemHard disk controller failure press F1 to try reboot Insert bootable media device Invalid partition table Invalid passwordMemory errors were detected while the system started up Memory size error Not enough memory Non-system disk or disk errorSyntax error Write-protect error First steps Troubleshooting 100 Battery replacementBeep codes 101 Beeps Description Troubleshooting steps 102 Settings in the Bios Setup utility are not retainedCD drive Your server does not recognize a CD or the CD drive Diskette drive is not recognized Cleaning CDsDiskette drive Your CD drive tray does not open 104 Expansion cardsFile management Hard drive To restore files that were deleted in Windows 2000 ServerYou receive an Insufficient disk space error message You receive a Non-system disk or disk error error message 106 Master boot record is corruptedYour server does not recognize an IDE drive Your server does not recognize a Scsi drive 107 To repair the master boot recordInternet To download the GWScan utility 108 Keyboard 109 MemoryModem telephone dial-up To check the dialing properties in Windows 2000 Server 110 Your 56K modem does not connect at 56KModem is not recognized by your server 111 To run modem diagnostics in Windows 2000 ServerModem is noisy when it dials and connects 112 To turn down the modem volume in Windows 2000 ServerMonitor 113 MouseText on the display is dim or difficult to read Mouse does not work 114 PowerPrinter Your server does not recognize a new processor You receive a Printer queue is full error messageYou receive a Printer is out of paper error message Processor 116 117 Telephone supportBefore calling Gateway Technical Support 118 Service descriptionResource Service description How to reach Telephone support 119 Resource Service description For more informationTutoring and training 120 121 SpecificationsServer a 122 System specificationsCase size Weight Fans Ports Card sizes Power supply 123 System board specifications Monitor 124Hardware Variable Requirements Environmental specifications125 126 Video specificationsResolution support Refresh Rate Hz Resolution 127 Electronic specificationsMemory map Interrupts Device Interrupt a Interrupt B Interrupt C Interrupt D PCI interrupt routing128 129 Additional specifications 130 131 To view all Bios settings 132 Bios menu Bios submenu Setting Value 133 134 135 Important safety informationSetting up your system Care during use Replacement parts and accessories136 137 Regulatory compliance statementsUnited States of America FCC declaration of conformity 138 139 Industry Canada IC Unintentional emitter per ICES-003 Canada140 141 Laser safety statement Trademark Acknowledgments 142All Rights Reserved 143 Index DDR Sdram 144 See card 145 146 147 Sdram 148 149 150 MAN 960 SYS GDE R1 12/02