Go to Step | Gateway 960 specification

Installing drives

If you are replacing the 3.5-inch drive adapter with a new 5.25-inch drive, remove the two screws connecting each mounting rail to the adapter, remove the rails, then attach the rails to the sides of your new drive.

Mounting rail screw

Mounting rail screw

Mounting rail screw

Mounting rail screw

Two screws for mounting the rail onto CD and diskette drives are stored on each rail. Screws for mounting onto most tape drives are stored in the case near the full-length card retention clips.

Tape drive screws

6 Go to Step 10.

www.gateway.com

51

Image 57

Gateway 960 manual Go to Step

Contents

Page Page Contents Troubleshooting Installing Components 121 Iii131 135Page Checking Out Your GatewayServer Front Front Back Interior Left side System board System board Right side Server Companion CD Getting HelpOnline help Gateway Web site Setting UpServerYour Converting to a rackmount server Setting up the hardware Surge protectors Protecting from power source problems Line conditioners Uninterruptible power supplies To start the server Starting your server Understanding the power-on self-test To select which device your your server boots fromWhen the power It means Indicator is To turn off the server Turning off your server Restarting rebooting your server To close unresponsive programs in Windows 2000 ServerTo restart your server Setting up the operating system Setting Up Your Server MaintainingServerYour Caring for your server Weekly Maintenance task Protecting your server from viruses Managing hard drive space Checking hard drive spaceTo check hard drive space in Windows 2000 Server Checking the hard drive for errors Using Disk CleanupTo use Disk Cleanup in Windows 2000 Server To check the hard drive for errors in Windows 2000 Server Click the Tools tab To defragment a hard drive in Windows 2000 Server Defragmenting the hard drive Backing up files Cleaning the exterior Cleaning your server Cleaning the keyboard Cleaning the screenCleaning the tape drive To clean your trackball mouse Cleaning the mouse Mouse rollers Creating startup diskettes Preparing for system recoveryCreating an emergency repair diskette To create startup diskettes in Windows 2000 Server Preparing for system recovery Maintaining Your Server To record your Bios configuration Keeping a record of system configuration To set the Bios security passwords System administrationManageX Event Manager Server security Option Description To view the event log Using your Server Companion CD ComponentsInstalling Preparing to install components Selecting a place to workGathering the tools you need Preventing static electricity discharge To open the server case Opening the server case Opening the server case Installing Components To close the server case Closing the server case Installing Components Installing drives To install a 5.25-inch drive Installing a media drive Installing drives Hard drive screws Go to Step Installing Components Screw Follow the instructions in Closing the server case on To install a hard drive Installing a hard drive Screw Installing drives Installing memory To install or replace memory PCI slot Description Installing PCI expansion cards To replace, add, or reseat a PCI expansion card Release lever Card retention cover Installing PCI expansion cards Follow the instructions in Closing the server case on To replace a processor Installing a processor Installing Components Installing a processor Processor 1 fan connector Processor 2 fan connector Installing a voltage regulator To replace the power supply Replacing the power supply Replacing the power supply Follow the instructions in Closing the server case on To replace the Scsi backplane Replacing the Scsi backplane Slide the hot-swap cage out about two inches from the case Replacing the Scsi backplane Thumbscrew Replacing the Scsi backplane Follow the instructions in Closing the server case on To replace the system board Replacing the system board System board tray thumbscrew Replacing the system board To replace a fan Replacing a fan Replacing a fan To replace the battery Replacing the Cmos battery Replacing the Cmos battery Installing Components Using the Bios Setup Utility To open the Bios Setup utility Opening the Bios Setup utility Recovering the Bios Updating the BiosTo update the Bios To recover the old Bios To reset the Bios Resetting the Bios Resetting Bios passwords Using the Bios Setup Utility Troubleshooting Safety guidelines Error messages Hard disk controller failure press F1 to try reboot Error loading operating systemInsert bootable media device Invalid configuration information Memory errors were detected while the system started up Invalid passwordMemory size error Invalid partition table Syntax error Non-system disk or disk errorWrite-protect error Not enough memory First steps Troubleshooting Battery replacement Beep codes100 101 Beeps Description Troubleshooting steps CD drive Settings in the Bios Setup utility are not retainedYour server does not recognize a CD or the CD drive 102 Diskette drive Cleaning CDsYour CD drive tray does not open Diskette drive is not recognized Expansion cards File management104 You receive an Insufficient disk space error message To restore files that were deleted in Windows 2000 ServerYou receive a Non-system disk or disk error error message Hard drive Your server does not recognize an IDE drive Master boot record is corruptedYour server does not recognize a Scsi drive 106 Internet To repair the master boot recordTo download the GWScan utility 107 108 Keyboard Modem telephone dial-up MemoryTo check the dialing properties in Windows 2000 Server 109 Your 56K modem does not connect at 56K Modem is not recognized by your server110 To run modem diagnostics in Windows 2000 Server Modem is noisy when it dials and connects111 To turn down the modem volume in Windows 2000 Server Monitor112 Text on the display is dim or difficult to read MouseMouse does not work 113 Power Printer114 You receive a Printer is out of paper error message You receive a Printer queue is full error messageProcessor Your server does not recognize a new processor 116 Telephone support Before calling Gateway Technical Support117 Resource Service description How to reach Service descriptionTelephone support 118 Resource Service description For more information Tutoring and training119 120 121 SpecificationsServer a Case size Weight Fans Ports System specificationsCard sizes Power supply 122 123 System board specifications 124 HardwareMonitor Environmental specifications 125Variable Requirements Resolution support Video specificationsRefresh Rate Hz Resolution 126 Memory map Electronic specificationsInterrupts 127 PCI interrupt routing 128Device Interrupt a Interrupt B Interrupt C Interrupt D 129 Additional specifications 130 131 To view all Bios settings 132 Bios menu Bios submenu Setting Value 133 134 Important safety information Setting up your system135 Replacement parts and accessories 136Care during use Regulatory compliance statements United States of America137 FCC declaration of conformity 138 139 Canada 140Industry Canada IC Unintentional emitter per ICES-003 141 Laser safety statement 142 All Rights ReservedTrademark Acknowledgments 143 Index DDR Sdram 144 See card 145 146 147 Sdram 148 149 150 MAN 960 SYS GDE R1 12/02