Symptom

 

 

 

Action

 

 

 

 

 

 

 

 

 

The

SMS configuration

list or Boot sequenceAdevice may

be

set

to

use the same SCSI bus

selection

menu shows

more SCSI devices

ID

as the control adapter. Note the ID being

attached to a controller/adapter than

usedare actuallybythe controller/adapter (this can be

attached.

 

 

checked

and/or

changed

via an SMS utility), and

 

 

 

 

verify

that

no

device

attached to the

controller is

 

 

 

 

set

 

to

use

that

ID. If

settings do not appear to

 

 

 

 

be

 

in

conflict,

go

to

“Boot Problems/Concerns”

 

 

 

 

on

page 4-27.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The

System

Management

Services menu is

The

 

device or

media you

are attempting

to boot

displayed.

 

from

may be

faulty.

 

 

 

 

1.Check the SMS error log for any errors. To check the error log:

a.Choose error log

b.If an error is logged, check the time stamp.

c.If the error was logged during the current boot attempt, record it.

d.Look up the error in Chapter 6 "Error Code to FRU Index" and do the listed action.

e. If

no recent error is logged in the error

log,

continue to the next step below.

2.Try to boot from an alternate boot device connected to the same controller as the original boot device. If the boot succeeds, replace the original boot device (for removable media devices try the media first).

 

 

 

 

 

 

 

 

3. Go

to

“MAP

1540:

Minimum

Configuration”

 

 

 

 

 

 

 

 

on

page 2-21.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You

cannot

load

diagnostics.

 

Go

to

“MAP

1020:

Problem

Determination”

on

 

 

 

 

 

 

 

 

page

2-7.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You have a problem that does

not preventGotothethe

Fast

Path

MAP Diagnosticsin the

 

system

from

booting.

 

 

Information

for

Multiple

Bus. Systems

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You

do

not

have

a symptom.

 

Go

to

MAP

0020

in

Diagnosticsthe

Information

 

 

 

 

 

 

 

 

for

Multiple Bus

Systems

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You

have

an

SRN.

 

 

 

Go

to

the

Fast

Path

MAP Diagnosticsin the

 

 

 

 

 

 

 

 

 

Information for Multiple Bus. Systems

 

 

 

 

 

 

 

 

 

 

 

 

You

suspect

a cable

problem.

 

Go

to

theAdapters,

Devices,

and Cable

 

 

 

 

 

 

 

 

 

Information

for

Multiple

Bus. Systems

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You

Cannot Find

the Symptom in

this Table

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All

other

problems.

 

 

Go

to

“MAP

1020:

Problem

Determination”

on

 

 

 

 

 

 

 

 

page

2-7.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2-67043 43P Series Service Guide

Page 42
Image 42
IBM SA38-0512-03 manual This Table