Enabling Power Supplies | Intel ZT 7102 guide

Intel® NetStructureTMZT 7102 Chassis Management Module

Power Supplies

13.5Inhibiting Power Supplies

Power supplies can be inhibited through the CMM. This is accomplished using the following command:

cmmset -l chassis -d psinhibitN -v 0

Where N is the number of the power supply that is to be inhibited.

Note: When a non-IPMI supply is inhibited, a SEL entry is logged indicating a failure condition. When the non-IPMI supply is enabled a SEL entry is logged indicating that the power supply has recovered from a failure condition. This does not occur in current IPMI-compliant power supplies.

13.6Enabling Power Supplies

To enable a supply which has been inhibited, issue the following command:

cmmset -l chassis -d psinhibitN -v 1

Where N is the number of the power supply that is to be enabled.

Note: When a non-IPMI supply is enabled a SEL entry is logged indicating that the power supply has recovered from a failure condition. This is because when a non-IPMI supply is inhibited, a SEL entry is logged indicating a failure condition. This does not occur in current IPMI-compliant power supplies.

84	Technical Product Specification

Image 84

Intel ZT 7102 manual Enabling Power Supplies

Contents

Technical Product Specification Intel NetStructure ZT 7102 Chassis Management Module Technical Product Specification Contents 16.1 3.1 11.1.2 15.3 20.2.1 Figures Tables 116 Revision History Date Revision Description ZT 7102 Features IntroductionOverview Functional Block Diagram Terms Used in This Document GlossaryAcronym Description Intel NetStructureTMZT 7102 Chassis Management Module Hardware Specifications System Architecture Backplane ConnectionsSlot Connections Power Modules Fan ModulesChassis Sensor Connections Chassis FRU Device Connections Face Plate Face Plate Faceplate Features Faceplate FeaturesFeature Purpose Connectors Board Dimensions and WeightPCB Dimensions Mechanical Connector Locations 1 J1 Backplane Connector 2 J2 Backplane ConnectorJ1 Connector Pinout Pin# 3 J3 Backplane Connector J2 Connector PinoutJ3 Connector Pinout Backplane Pin Descriptions Pin Type DefinitionsPin Descriptions Sheet 1 Pin Type Definition 5 JA1 Ethernet Port Pin Descriptions Sheet 2 7 J7 Telco Alarm Connector 6 J6 Serial PortJA1 Ethernet Port Pinout J6 Serial Port Pinout CMM Power J7 Telco Alarm Connector PinoutCMM Power Availability Electrical and Environmental Power Ramp Circuitry Operating TemperatureReliability Absolute Maximum Ratings Onboard Switches DC Operating CharacteristicsDC Operating Characteristics Switch Cross Reference Table Switch Descriptions 10.1.1 S1 Alarm Cutoff and Board Reset10.1.2 SW1-1 Password Reset Processor and Chipset Memory FlashDual Ethernet Controllers Serial I/O Telco Alarm Signal Alarm RelaysReal Time Clock Network Time Synchronization Watchdog Timer Battery BackupReplacing the Battery Battery Characteristics Running Your System Without a CMM Software Specifications Operating System Command Line Interface CLIRemote Procedure Call RPC Interface Ethernet Interfaces Sensor Event Logs SEL CMM SEL ArchitectureSatellite Management Controller SMC Boards Baseboard Management Controller BMC Boards Hardware Redundancy Specification CMM Redundancy, Synchronization and FailoverSynchronization Synchronization Requirements CMM SynchronizationFiles or data Description Path CMM Failover Scenarios That Force a FailoverScenarios That Prevent Failover Scenarios That Failover to a Healthier Standby CMM Scenarios That Failover to an Equally Healthy CMM Failover TimingManual Failover CMM Installation and Removal Installing the CMMUnpacking Connectivity Removing the CMM Ejector Handle Operation Intel NetStructureTMZT 7102 Chassis Management Module Intel NetStructureTMZT 7102 Chassis Management Module Built-In Self Test Bist Test Flow Boot-BIST Boot-BIST Early-BIST Mid-BIST Late-BISTEarly-BIST Mid-BIST Late-BIST Event Log Area and Event Management OS Flash Corruption Detection and Recovery Design Monitoring the Static ImagesMonitoring the Dynamic Images CMM Failover Bist Test Descriptions Fpga Version Check 5 DS1307 RTC TestNIC Presence/Local PCI Bus Test OS Image Checksum Test CMM Connection and Setup Connecting to the CLIConnecting through a Console CLI Overview Initial Setup Logging in for the First Time Setting IP Address PropertiesFTP Into the CMM Setting Eth0 to Dhcp Eth1 and Eth11 Rebooting the CMM Setting a HostnameSetting Auto-Logout Time Limit Command Line Interface CLI Syntax and Arguments Cmmget and cmmset syntaxHelp Parameter -h Location Parameter -l Target Parameter -t Dataitem Parameter -dTarget -t Keywords Dataitem -d Keywords for All Locations Sheet 1 Dataitem -d Keywords for All Locations Sheet 2 Dataitem -d Keywords for System locationDataitem -d Keywords for BladeN Locations Data Item Description Get Valid Set Dataitem -d Keywords for Chassis Location Dataitem -d Keywords for CMM Location Sheet 1Set Value Parameter Sample CLI OperationsDataitem -d Keywords for CMM Location Sheet 2 Generating a System Status Report Resetting the Password Resetting the Password in a Single CMM SystemResetting the Password in a Dual CMM System Intel NetStructureTMZT 7102 Chassis Management Module Sensor Types Threshold-Based SensorsDiscrete Sensors Threshold-Based Sensor Events Intel NetStructureTMZT 7102 Chassis Management Module Health Event Strings Syntax of Health Event StringsHealthevents Query Event Syntax SEL Event Syntax Sensor Targets Snmp Trap Event SyntaxCMM Sensor Targets Sensor Target Description Healthevents Queries HealthEvents Queries for Individual SensorsHealthEvents Queries for All Sensors on a Location No Active Events List of Possible Health Event Strings Not Present or Non-IPMI Locations PowerSupplyN Location IPMI-Compliant Supplies Only Power Supply Event Strings PowerSupplyNAll Locations Event String Event Code Event Severity 11.4.3 CMM Location Bist Event Strings Bist Sheet 1 Chassis Location Slot Event Strings Slot N Event CMM Redundancy Event Strings CMM 1-2 RedundancyCMM Failover Event Strings CMM Failover CMM File Sync Event Strings CMM File Sync Chassis Sensor Event StringsEvent String Event Code If HealthEvents, its Severity Intel NetStructureTMZT 7102 Chassis Management Module Slot Power Control Slot Power-Up SequenceAssertion of BDSEL# System Master Boards Obtaining the Power State of a Board Drone Mode BoardsAssertion of HEALTHY# During Power-Up Fabric and PCI-Less Slots Controlling the Power State of a Slot Power Sequencing Commands and PoliciesPowering Off a Board Powering On a Board Setting the Healthy# Ramp-Up Time Retrieving the Maximum Power-Up AttemptsSetting the Maximum Power-Up Attempts Retrieving the Healthy# Ramp-Up Time Power Sequencing SEL Events CMM detects a slot has been placed in offline or active Intel NetStructureTMZT 7102 Chassis Management Module Power Supplies Power Supply DetectionInhibit, Degrade, and Fail Signals Inhibiting Power Supplies Enabling Power Supplies Drone Mode SBC Support Adding a Drone Mode Capable SBCRemoving a Drone Mode Capable SBC Intel NetStructureTMZT 7102 Chassis Management Module Setting a Slot to Offline Mode Setting a Slot to Active ModeLimitations of the Offline Mode Active vs. Offline Slots Intel NetStructureTMZT 7102 Chassis Management Module Obtaining FRU Information FRU InformationFRU Query Syntax Data Item Description Chassis FRU Validity Check Setting Fan Speed Fan Control and MonitoringAutomatic Fan Control Considerations for Turning Off the Fans Querying Fan Tray Sensors CMM Scripting CLI ScriptingAssociating Scripts to Event Severity Script Synchronization Setting Scripts for Specific Individual Events Listing Scripts Associated With EventsRemoving Scripts From an Associated Event Event Codes Setting Event Scripts Slot Events Intel NetStructureTMZT 7102 Chassis Management Module Snmp High Level SNMP/MIB Layout Querying Non-IPMI Compliant Blades and Power Supplies CMM MIBMIB Design Snmp Agent Configuring the Snmp Agent Port Configuring the Agent to Respond to Snmp v3 RequestsConfiguring the Agent Back to Snmp Setting up an Snmp v3 MIB Browser Configuring and Enabling Snmp Trap Addresses Snmp Trap Utility Alerts Using SNMPv3 Alert Using UDP AlertSecurity Model Snmpd.conf 102 Setting Up the RPC Interface Using the RPC Interface20.0 RPC 103 GetAuthCapability ChassisManagementApi104 105 Error and Return Codes for the RPC Interface Sheet 1 Code # Error Code String Error Code Description106 Error and Return Codes for the RPC Interface Sheet 2 107 Error and Return Codes for the RPC Interface Sheet 3 108 Error and Return Codes for the RPC Interface Sheet 4 ChassisManagementApi Threshold Response Format109 ChassisManagementApi String Response Format Threshold Response FormatsString Response Formats Sheet 1 110 String Response Formats Sheet 2 111 String Response Formats Sheet 3 112 ChassisManagementApi Integer Response Format String Response Formats Sheet 4Integer Response Formats Sheet 1 113 FRU String Response Format Integer Response Formats Sheet 2FRU Data Items String Response Format Sheet 1 114 RPC Sample Code RPC Usage ExamplesFRU Data Items String Response Format Sheet 2 115 RPC Usage Examples Sheet 1 116 RPC Usage Examples Sheet 2 117 RPC Usage Examples Sheet 3 118 Command Logging 119 120 Telco Alarm Sensors Configuring the Telco Alarm Connector PinsTelco Alarm Connector Sensor Naming 121 Telco Alarm Sensors and Redundancy Sensor Names using Snmp122 Application Hosting System DetailsStartup and Shutdown Scripts System Resources Available to User Applications Ram Disk Directory Structure RAM-Disk Storage LocationsRAM Constraints Interrupt Constraints Busless Backplane Support 125 126 Key Features of the Firmware Update Process Update Process ArchitectureUpdating Software 127 Critical Software Update Files and Directories Update PackageList of Critical Software Update Files and Directories Contents of the Update Package Sheet 1 Update Package File Validation Update Firmware Package VersionContents of the Update Package Sheet 2 129 SaveList and Data Preservation Component VersioningSaveList Items and Their Priorities Sheet 1 130 Update Mode UpdateMetadata FileSaveList Items and Their Priorities Sheet 2 131 Updating to a Newer Synchronization Version Updating to an Older Synchronization VersionSynchronization Behavior for Differing Synch Versions 132 Single CMM System Redundant CMM SystemsCLI Support Updating to the Same Synchronization Version Update Mode User Scripts Data Restore User ScriptsHooks for User Scripts 134 135 Update Process 136 Update Process Status and Logging Debugupdate VariableUpdate Process Sensor and SEL Events 137 RedBoot Update Process Required SetupUpdate Procedure 138 Example CLI Commands Sheet 1 Use Case CLI Command Return139 Example CLI Commands Sheet 2 140 Intel CompactPCI* Product Information CompactPCIIntel IOP310 Processor Chipset 141 142 Returning a Defective Product RMA For the Americas143 For Emea For Apac144 145 146 Technical Support and Return for Service Assistance Sales Assistance147 148 Safety CE CertificationEmissions Test Regulations EN 50081-1 Emissions Product Safety Information Safety PrecautionsRegulatory Information Industry Canada Canada 151 152