Intel® NetStructureTMZT 7102 Chassis Management Module

 

 

 

 

 

Hardware Specifications

Table 9. Pin Descriptions (Sheet 2 of 2)

 

 

 

 

 

 

 

 

 

Name

Count

 

Type

Description

 

 

 

 

 

 

 

SDTR

1

 

O

Serial data terminal ready

 

 

 

 

 

 

 

SRI

1

 

I

Serial ring indicator

 

 

 

 

 

 

 

SCD

1

 

I

Serial carrier detect

 

 

 

 

 

 

 

RpTx(+-)

2

 

I/O

10/100 Ethernet To rear panel

 

 

 

 

 

 

 

RpRx(+-)

2

 

I/O

10/100 Ethernet From rear panel

 

 

 

 

 

 

 

NEG_O

1

 

O

Negotiate output to other CMM

 

 

 

 

 

 

 

NEG_I

1

 

I

Negotiate input from other CMM

 

 

 

 

 

 

 

HLY_O#

1

 

O

Healthy output to other CMM

 

 

 

 

 

 

 

HLY_I#

1

 

I

Healthy input from other CMM

 

 

 

 

 

 

 

PRES_I#

1

 

I

Other CMM is present (0V)

 

 

 

 

 

 

 

PRES_O#

1

 

O

Grounded on CMM.

 

 

 

 

 

 

 

GA0

1

 

I

Location Address

 

 

 

 

 

 

 

CMM_SEL#

1

 

I

Tells CMM it has been seated. (Backplane grounds

 

 

this pin)

 

 

 

 

 

 

 

 

 

 

 

 

GND

14

 

I

CMM GND

 

 

 

 

 

 

 

IPMB_PWR

8

 

I

CMM Power

 

 

 

 

 

 

 

BP_12V, BP_N12V,

 

 

 

 

 

BP_5V, and

4

 

I

Monitor backplane power 12,-12,5,3.3

 

BP_3.3V

 

 

 

 

 

 

 

 

 

 

 

RPMAC#

1

 

I

Rear panel major alarm clear

 

 

 

 

 

 

 

RPMIC#

1

 

I

Rear panel minor alarm clear

 

 

 

 

 

 

 

RPCR#

1

 

O

Rear panel critical alarm relay

 

 

 

 

 

 

 

RPMAR#

1

 

O

Rear panel major alarm relay

 

 

 

 

 

 

 

RPMIR#

1

 

O

Rear panel minor alarm relay

 

 

 

 

 

 

 

VIO

1

 

I

Backplane IO voltage (may not be present in non-PCI

 

 

system)

 

 

 

 

 

 

 

 

 

 

 

 

RES

18

 

NC

No Connect on Backplane

 

 

 

 

 

 

 

TOTAL

220

 

 

 

 

 

 

 

 

 

2.8.5JA1 Ethernet Port

JA1 is an RJ-45 Ethernet port providing 10 Mbit (10BASE-T) and 100 Mbit (100BASE-TX) protocols. JA1 connects to the CMM's LAN0 Ethernet channel. A second Ethernet channel, LAN1, is only available at the backplane.

Two LEDs are located in the RJ-45 Ethernet connector:

Yellow indicates speed

Green indicates a link/activity

See Table 10 for JA1 Ethernet port pin definitions.

Technical Product Specification

27

Page 27
Image 27
Intel ZT 7102 manual 5 JA1 Ethernet Port, Pin Descriptions Sheet 2