Specifications for Network Scanner, 145 | Sharp TINSE2026QSZZ

SPECIFICATIONS FOR NETWORK SCANNER

Maximum original size	11" x 17" or A3

Optical resolution	400dpi

Output resolution	200, 300, 600dpi

Output modes	1bit/pixel

Halftone processing	Error dispersion (200/300/600dpi)

File format	File type: TIFF/PDF
	Compression mode: MH (G3)/MMR (G4)/NONE

File creation method	One file for all pages/One file per each 1 to 6 pages

Two-sided originals	Possible (when an RSPF is installed)

Scan destinations	Scan to FTP, Scan to Desktop, Scan to E-mail

Web browser	Internet Explorer 6.0 or later (Windows), Netscape Navigator 7.0
	or later, Safari 1.2 or later (Macintosh)

Management system	Uses built-in Web server

Network protocol	TCP/IP, SMTP, LDAP, FTP

Supported mail system	Mail servers supporting SMTP

LAN connectivity	10Base-T/100Base-TX

Number of destinations	200 maximum

Number of destinations for Scan To E-mail	100 maximum*
broadcast transmission

*Multiple e-mail addresses (up to 100) can be stored as a group. Note that this may reduce the maximum number of destinations (normally 200) that can be stored.

Some discrepancies may exist in the illustrations and content due to improvements to the machine.

Scanning margins

When scanning an original, the area indicated in the following diagram cannot be scanned.

Approx. 0.1" (2.5mm)

Approx. 0.1" (2.5mm)

Approx. 0.1" (2.5mm)

Scanning margins

Approx. 0.1" (2.5mm)

Area that can be scanned

Scan size setting

Scan size setting

9

145

Image 147

Sharp TINSE2026QSZZ operation manual Specifications for Network Scanner, 145, Scanning margins, Tcp/Ip, Smtp, Ldap, Ftp

Contents

MX-M260 MX-M310 For Your Records Contents 115 103110 111 127 117119 123 Air conditioner or Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Changes, e.g., near an Scratches or smudges on the drum will cause dirty copies Safety precautionsLaser Information Do not touch the photoconductive drum green portion Online manual for printer Using the ManualSoftware setup guide for printer Environmental Information Meaning of R in Original and Paper Size Indications Conventions Used in this ManualExplanation of words and illustration High-quality digital image Main FeaturesEnhanced copying features High-speed laser copying Exterior Part Names and Functions Interior Operation Panel Beep tone Using the touch panel Selecting a functionTouch Panel Example Print JOB key Mode switching keysDisplay switching keys Job list Turn the power switch to the on position Power on and OFFPower on Power OFF Auto power shut-off mode Initial SettingsPower Save Modes Preheat mode Letterhead Paper 11 x Tray Paper tray type Paper type Size Weight CapacityLoading Paper Paper Letterhead paper Follow these guidelines when using special papersSpecial papers Envelopes Loading the paper in the paper tray Loading Paper Important points when inserting paper in the bypass tray Loading paper in the bypass traySet the paper guides to the copy paper width Changing a TRAY’S Paper Type and Paper Size Settings Touch the Tray Settings keySelect the tray in which you loaded paper Setting the paper type in the bypass tray Main Screen of Copy Mode Press the Start key How to place the originalNormal Copying Copying from the Document Glass Stream feeding mode Copying from the RspfCopying a large number of originals Acceptable originals Points to Note When Making CopiesDocument glass and Rspf Originals that can be used in the Rspf Touch the Special Modes key Select the MIX Size Original Feeding Mode checkboxCopying originals of mixed length Mixed feeding Automatic copy image rotation Rotation copying Set the type of paper that You loaded in the bypassTray. p.21 Original → Paper Using the Document GlassAutomatic TWO-SIDED Copying Touch the One-sided to two-sided copy key Touch the OK key Original for the front side is scanned Using the RspfTouch the desired copy mode To cancel automatic two-sided copying, press the Clear key Exposure value guidelines Exposure AdjustmentTouch the Exposure key Manually adjust the copy exposure Selecting the original image type Then select the desired paper size REDUCTION/ENLARGEMENT/ZOOMAutomatic Ratio Selection Place the originals. p.23, p.24 200%, 400% Preset reduction keys 25%, 50%Manual Ratio Selection Menu Touch the XY Zoom key Place the originals. p.23, p.24 Touch the Copy Ratio key Touch the Y key Copy ratio in the vertical Y direction Press the Interrupt key to interrupt the copy run Interrupting a Copy RUN Enabling the offset function Copy Finishing FunctionsSort Copy Group Copy Touch the Sort or Group key Touch the OK key When using the document glassSystem Settings Administrator Touch the Output key Insert the originals face up Place each original face down Using the RspfStaple Sort Orientation of the Original and Stapling Positions Copying will start after all originals have been scanned Touch the OK key When using the RspfPlace the originals. p.23, p.24 Touch the Output key Touch the Staple Sort key Special Modes Function General Procedure for Using the Special FunctionsTouch the key of the desired special mode Example Selecting the margin shift Select the shift direction Adjust the shift width as needed and touch the OK keyMargin Shift Copy Touch the Margin Shift key in the special modes screen Touch the Erase key in the special modes screen Select the desired erase modeAdjust the erase width as needed and touch the OK key Erase Copy Place the originals on the document glass. p.23 When copying book originalsDual page Copy Touch the Dual page Copy key in the special modes screen Specify whether 1-sided or 2-sided originals will be copied Pamphlet CopyTouch the OK key in the special Modes screen JOB Build Mode Touch the JOB Build key in the special modes menu screenTouch the READ-END key Multi Shot Copy Touch the inside OK key Original SizeTouch the Manual key Select the original size Cover Copy Copying onto a coverNot copying onto a cover Specify whether or not the front cover is to be copied on Touch the OK key in the cover setting screenSelect the covers that you wish to add Load the cover paper to be used into the bypass tray Reverse Copy Touch the outer OK key Card Shot Back side of the card is scanned and copying begins Place the original on the document glassPlace the back side of the original Front side of the card Is scanned Introduction Network Scanner Function About the Network Scanner Function Accessing WEB Pages Use the following procedure to access the Web pagesOpen the Web browser on your computer About the WEB Basic Settings for Network Scanning When you have completed all of the entries, click Submit Smtp Server and DNS Server SettingsConfiguring Smtp server settings Configuring DNS server settings Configuring Ldap Server Settings When Using AN Ldap Server Programming Custom Index Names FTP Setting UP Destination InformationStoring destinations for Scan to E-mail Click E-mail Click Destination in the menu frame Storing destinations for Scan to FTP Storing destinations for Scan to Desktop Storing Groups Scan to E-mail Editing and deleting programmed transmission destinations Click Sender in the menu frame Click Edit or Delete Editing and deleting programmed senders information Enter the current password in Admin Password Enter passwords in User Password and Admin PasswordEntered password is stored Logging in when user authentication is enabled Settings required for user authentication Condition settings screen Initial Screen of Scanner Mode Address book screen Touch the Address Book key Load the original Adjust the resolution setting. p.80Sending AN Image Basic Transmission Method After the final page is scanned, touch the READ-END key Using the document glassTouch the one-touch key of the desired destination Enter a file name for the scanned image. p.82 E-mail address entry Transmission Methods for Scan to E-MAILSending an image by entering an e-mail address manually Continue from of Basic Transmission Method p.73 Touch the ADD Selected key Touch the Global Address Search key Initial screen Continue from of Basic Transmission Method p.72 to Touch the JOB Build key Selected size appears in the top half of the Original key Scanning SettingsManually Setting the Scanning Size Touch the desired original size key Selecting the original type Adjust the densitySelecting the Quality Touch the Quality key Touch the desired resolution key Selecting the ResolutionChange the resolution Touch the Resolution key Select the file type Compression modeSelecting the File Format Touch the File Format key Up to 64 characters can be entered Changing the Send SettingsTouch the Send Settings key Touch the OK key in the send settings screen Touch the STOP/DELETE key Canceling AN E-MAIL/FTP TransmissionPress the JOB Status key Touch the Scan to key Metadata Delivery Data Entry Storing Metadata Sets Settings Required in the WEB PagesPreparations for Metadata Transmission Metadata Transmission for Scan to Desktop Touch the key of the value that you wish to enter Transmitting MetadataTouch the Data Entry key Touch the key of the metadata that you wish to use Auto Subject Name entered Description Where entered Metadata fieldMetadata Fields Sender Name Touch the List Print key Touch the Printer Settings List keySystem settings screen will appear Checking the IP Address System Settings System Settings General Procedure for System Settings Settings JOB Program Memory Storing a JOB ProgramTouch the STORE/DELETE key Touch the program number key of the desired program Executing a JOB ProgramDeleting a Stored JOB Program Press the #/P key Enter your account number 5 digits with the numeric keys Auditing ModeCopying When Auditing Mode is Enabled When the copy job is finished, press the Logout key Programming a Administrator Password Purpose of the Administrator Settings Example Touch the Administrator Settings keyPress the Clear ALL key to exit the setting Touch the OK key. You will return to the screen of step Example Auditing mode Keys Used in Administrator Settings Program name Factory default Settings Administrator Setting List 100 Programs for Print Mode Administrator Setting Menu 101Level 102 General Programs Account Control103 Account Number Control Account Limit SettingCancel Jobs of Invalid Accounts 104 105 Energy Save 106 Operation Settings 107 Device Control 108 109 Product KEY Programs for Copy Mode Copy Settings110 Programs for Print Mode Print Settings111 Network Port Emulation Switching Hexadecimal Dump ModeTimeout USB Port Emulation Switching 113 Restore Configuration *1 Reset the NIC *1Restore Factory Defaults *1 Store Current Configuration *1 Programs for Network Scanner Mode Scanner Settings115 116 Problems related to machine operationPaper feeding problems Image quality problems Message Cause and solution Display Messages117 118 Troubleshooting Problems related to machine operation119 120 121 Paper feeding problems 122 Image quality problems 123 Problems When the Network Scanner Function is Used 124 Resolution 125 Error codesError Code Table Display Messages Original image samples Important Points When Using Scan to E-MAILIf Your E-MAIL is Returned 126 First, locate the misfeed Misfeed RemovalMisfeed Removal Guidance 127 Misfeed in the Rspf 128Remove the misfed original Misfeed in the paper feed area Misfeed in the Bypass TrayMisfeed in the Machine 129 Turn the roller rotating knob in the direction of the arrow Misfeed in the fusing area130 Close the front cover and side cover Replace the upper paper tray Misfeed in the Center TrayMisfeed in the Upper Paper Tray 131 Misfeed in the Lower Paper Tray Misfeed in the Right Tray132 Close the upper right side cover Misfeed in the Upper Exit AreaMisfeed in AN Output Tray 133 Replacing the Toner Cartridge 134Close the front cover Replace the staple case Staple Cartridge Replacement135 Replacing the staple cartridge 136 Removing staple jamsFollow the steps below to remove a staple jam 137 Cleaning the MachineChecking the Toner Quantity and Total Count Document Glass and Rspf Cleaning the scanning glass for Rspf Bypass Tray Paper Feed Roller138 139 Peripheral Devices Part names SpecificationsFinisher MX-FN13 140 Paper Upper tray Sheet Paper Feed Unit141 MX-DE10 MX-DE11 Store the supplies in a location that is Storage of SuppliesProper Storage 142 143 Specifications Reversing single pass feeder Rspf 144 TCP/IP, SMTP, LDAP, FTP Specifications for Network Scanner145 Scanning margins 146 Material Safety Data Sheet Hazards Identification 147 Personal Protective Equipment 148 Disposal Considerations 149 Sharp Corporation Nagaike-cho, Abeno-ku, Osaka, Japan 150 151 Exposure Limit Values 152 153 Symbols Index154 155 156 157 158 Misfeeds, removing Configuring the administrator settingsTroubleshooting and maintenance 159 Trademark acknowledgments 161 Factory default passwords Web pages To the Administrator of the MachineFactory default passwords Factory default administrator password Memo Connectors Page 2009G KS1 TINSE2026QSZZ Sharp Electronics Corporation