Sonic Alert DCP301 user manual Constant-value operation data settings C N S t, D E

Chapter 7. PARAMETER SETUP

■Constant-value operation data settings “C N S t”

No.	Item Code	Item	Factory	User				Setting
			Setting	Setting
1	M .O D E	Operation mode	0		0: Program operation
					1: Constant-value operation
					[Note]
						This setting can be changed only in the READY mode.
2	S P	SP1	0		This setting can be set in the SP1 lower to upper limit
					range in setup data settings C 0 q and C 1 0.
3	S P 2	Unused	0		[Note]
						“– – – –” is displayed and setting is not possible.
4	E V 1	Event 1 setting	9999		-1999 to 9999U			(event type is deviation or SP)
		value			0 to 9999U			(event type is absolute value deviation)
5	E V 2	Event 2 setting	9999		-10.0 to 110.0% (event type is MV or MFB)
		value			[Note]
6	E V 3	Event 3 setting	9999			When the event configuration data type setting is ≥ 50
		value				for each event, “– – – –” is displayed and setting is not
						possible.
7	—	Unused	—		[Note]
8	—	Unused	—			“– – – –” is displayed and setting is not possible.
9	—	Unused	—
10	—	Unused	—
11	P .	Proportional band	100.0		P		: 0.0 to 999.9% (0D, 6D output models)
		(CH1)					0.0 enables ON-OFF control.
12	I .	Reset time (CH1)	0				0.1 to 999.9% (models other than 0D and 6D
13	D .	Rate time (CH1)	0				models)
14	O L .	MV lower limit (CH1)	0.0		I		: 0 to 3600s
15	O H .	MV upper limit (CH1)	100.0				0 disables integral action.
16	R E .	Manual reset (CH1)	50.0		D		: 0 to 1200s
17	B R .	Brake (CH1)	0				0 disables derivative action.
18	D P .	Disturbance inhibit	100.0		O L : -10.0 to MV upper limit %
		proportional band			O H : MV lower limit to 110.0%
		(CH1)			R E : 0.0 to 100.0%
19	D I .	Disturbance inhibit	120		B R : 0 to 30
		reset time (CH1)					0 disables the brake function.
20	D D .	Disturbance inhibit	0		D P		: 0.1 to 999.9%
		rate time (CH1)			D	I	: 1 to 3600s
21	P .-C	Proportional band	100.0		D D : 0 to 1200
		(for cool control)					0 disables derivative action.
22	I .-C	Reset time (CH1)	0
		(for cool control)			[Note]
23	D .-C	Rate time (CH1) (for	0		•	On 0D and 6D output models, when P setting is 0.0,
		cool control)				ON-OFF control is enabled. “– – – –” is displayed for
24	O L .-C	MV lower limit (CH1)	0.0			items I, D, O L, O H, R E, D P, D I and D D, and
		(for cool control)				setting is not possible.
25	O H .-C	MV upper limit (CH1)	100.0		•	When variable parameter M .-Csetting is 2 (estimated
		(for cool control)				position control only) on 2G output models, “– – – –” is
26	R E .-C	Manual reset (CH1)	50.0			displayed for items OL and OH, and setting is not
		(for cool control)				possible.
					•	When I setting is not 0, “– – – –” is displayed for R E
						and setting is not possible.
					•	When variable parameter S T setting is 0 (smart-tuning
						disabled), “– – – –” is displayed for B R and setting is
						not possible.
					•	When variable parameter 2 P I D setting is 0 (2
						degrees of freedom PID disabled), the items for D P,
						D I, D D are not displayed.
						For details, see the Note for PID parameters.
27	—	Unused	—		[Note]
28	—	Unused	—			“– – – –” is displayed and setting is not possible.
29	—	Unused	—
30	—	Unused	—

7-42