Using the upgrade rom-monitor Command | Cisco Systems CISCO7201

Chapter 3 Starting and Configuring the Router

Upgrading ROMmon on the Cisco 7201

Using the show rom-monitor Command and showmon Command

Use the show rom-monitorcommand if you are in Cisco IOS, or the showmon command if you are in ROMmon, to determine which ROMmon images are available. See the following examples for information shown in the output of the show rom-monitoror showmon commands:

•If you are in Cisco IOS, use the show rom-monitorcommand:

Router> show rom-monitor

ReadOnly ROMMON version:

System Bootstrap, Version 12.2(20031011:151758)

Copyright (c) 1994-2003 by cisco Systems, Inc.

Upgrade ROMMON version:

System Bootstrap, Version 12.2(20031011:151758)

Copyright (c) 1994-2003 by cisco Systems, Inc.

Currently running ROMMON from Upgrade region

ROMMON from Upgrade region is selected for next boot

•If you are in ROMmon, use the showmon command:

rommon 1 > rommon CLI showmon

ReadOnly ROMMON version is:

System Bootstrap, Version 12.4(4r)XD5, RELEASE SOFTWARE (fc1) Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 2006 by cisco Systems, Inc.

No upgrade ROMMON version present

ReadOnly ROMMON currently running

ReadOnly ROMMON is selected for next boot rommon 3 >

Using the upgrade rom-monitor Command

Use the upgrade rom-monitor file file_id command to program the ROMmon.

See the following example of the upgrade rom-monitorcommand:

Router# upgrade rom-monitor file tftp://00.0.00.0/biff/C7200_c7200p-kboot-mz Loading pgettner/C7200_NPEG2_RMFUR.srec from 00.0.00.0 (via GigabitEthernet0/1):

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[OK - 392348 bytes]

This command	will reload the router. Continue? [yes/no]:yes
ROMMON image	upgrade in progress.
Erasing boot	flash eeeeeeeeeeeeeeeeee

		Programming boot flash ppppp
		Now Reloading via hard watchdog timeout
		Unexpected exception, CP
		System Bootstrap, Version 12.2(20031011:151758) [biff]
		Copyright (c) 1994-2003 by cisco Systems, Inc.
		Running new upgrade for first time
		Cisco 7201 Installation and Configuration Guide
		Cisco 7201 Installation and Configuration Guide

	OL-11364-04			3-23
	OL-11364-04			3-23

Image 87

Cisco Systems CISCO7201 Using the show rom-monitor Command and showmon Command, Using the upgrade rom-monitor Command

Contents

Americas Headquarters Cisco 7201 Installation and Configuration GuidePage N T E N T S Attaching the Cable-Management Bracket Using the upgrade rom-monitor Command Boot Prompt boot# Bits 0-3 C-2 Viii Document Revision History Document ObjectivesDocument Version Date Change Summary Chapter and Appendix Number and Title Description Safety Warnings and CautionsAudience Document Organization Bewaar Deze Instructies Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar GEM Disse Anvisninger Page Xvi Lithium Battery Caution Related Documentation Xviii Overview Cisco 7201 Features Front View Cisco 7201 Hardware Overview Color-Activity Behavior Description Power Up StateFaceplate LEDs LED Label Types of SFP Module Latches SFP Module Information USB Port Information CompactFlash Disk Information Rear View Power Supply LEDs Power Supply LEDs System Board Interior View System Management Functions Cisco 7201 Router Installation Checklist Checking the Shipping Container Contents Verified Task Date Preparing to Install the Cisco 7201 Router Installing the Cisco 7201 Router Cisco Site Preparation and Unpacking Tools and Parts Required Electrical Equipment Guidelines Preventing Electrostatic Discharge DamageSite Requirement Guidelines General Tabletop or Workbench Installation Installing the Router Rack-Mounting a Cisco 7201 Router Cisco Installing Rack-Mount Brackets on the Front of the Chassis Attaching the Cable-Management Bracket Installing Rack-Mount Brackets on the Rear of the Chassis Installing the Chassis in the Rack Installing the Cisco 7201 Router in a Two-Post Rack Two-Post Rack Installation Installing the Cisco 7201 Router in a Four-Post Rack Four-Post Rack Installation Attaching a Chassis Ground Connection Fan vents Chassis ground connector Attaching the Grounding Lug Connecting I/O Cables Connecting Port Adapter Cables Adapter DTE M/F Pins DCE M/F Pins Mmod Pins Connecting Console and Auxiliary Port Cables Fdte FdceMmod 7201 Connecting the Fast Ethernet Management Port Cable Gigabit Ethernet SFP Connection Equipment Connecting Native Gigabit Ethernet Cables Cisco 7201 Installing the SFP Module Optical Fiber Cables 16 SFP Port Connections Mode-Conditioning Patch Cord Description 17 Mode-Conditioning Patch Cord Assembly for an SFP Module Attaching the Gigabit Ethernet RJ-45 Cables Attaching the Mode-Conditioning Patch Cord Input/output cables Cable-management bracket Using the Cable-Management Bracket Connecting AC-Input Power Connecting Power 20 Power Supply Slot 1 and Slot 22 Power Supply Slot 1 and Slot Connecting DC-Input Power 23 Locating the DC Grounding Stud and Grounding Materials Installing the DC Grounding Leads 24 Stripping the DC-Input Power Ground Wire Locate and remove the terminal block plug Wiring the DC-Input Power Source 27 Positive and Negative Positions Negative Return + 29 Inserting Wires into the Terminal Block Plug 31 Completed Wiring of Terminal Block Plug 32 Inserting the Terminal Block Plug in the Block Header Tie wrap Terminal block plug OL-11364-04 Functional Overview Starting and Configuring the Router Router# show interfaces Chassis Slot and Logical Interface Numbering MAC Address Environmental Monitoring and Reporting Functions Online Insertion and Removal Parameter High Warning High Critical Shutdown Environmental Monitoring Reporting Functions Router# show environmentRouter# show environment last CPU Router# show environment all Checking Conditions Prior to System Startup Starting the System and Observing Initial ConditionsFan Failures Configuring a Cisco 7201 Router Performing a Basic Configuration Using AutoInstall Performing a Basic Configuration Using the Setup FacilityHostname# copy running-config startup-config Restricted Rights Legend Configuring Global Parameters OK? Enter enable secret, enable, and virtual terminal passwords Configure System Management? yes/no no No ipx routing SFP Configuring the Native Gigabit Ethernet InterfacesExample Media Type Speed Duplex Debugging Interface counters may be cleared reset by using the command Configuring Port Adapter Interfaces Configuring Fast Ethernet Interfaces Configuring Synchronous Serial Interfaces Would you like to enter the initial dialog? yes no Checking the Running Configuration Settings Saving the Running Configuration to NvramPrompt changes to the privileged Exec prompt Upgrading ROMmon on the Cisco Performing Other Configuration Tasks Router show rom-monitor Using the show rom-monitor Command and showmon CommandUsing the upgrade rom-monitor Command If you are in ROMmon, use the showmon command Rommon 2 rommon-pref readonly Troubleshooting the UpgradeROMmon Upgrade Error Messages Changing Preferences to Change the ROMmon Image Boot of a corrupted upgrade image ROMmon upgrade image is too bigHardware does not support ROMmon upgrade Upgrade command with incorrect file type Overview of the Password Recovery Procedure Replacing or Recovering a Lost Password Details of the Password Recovery Procedure Router# show startup-configPress Return. The user Exec prompt is displayed as follows Hostnameconfig# interface gigabitethernet 0/0 Change all three passwords using the following commandsRouter# configure memory Hostname# configure terminal Viewing Your System Configuration Router# show versionDiag Performing Complex Configurations Replacing Cisco 7201 Field-Replaceable Units Removing an SFP Module Removing and Installing an SFP ModuleInstalling an SFP Module Use the following procedure to install an SFP module Installing and Removing a CompactFlash Disk Removing and Installing the CompactFlash Disk Connecting a USB Flash Memory Module to a Router USB Port Removing and Installing a Port Adapter or Service Adapter Slide the port adapter lever left to the locked position Installing a Port Adapter or Service Adapter Removing the AC Power Supply Removing and Installing an AC Power Supply Removing the AC Power Cable Installing the AC Power Supply Installing the AC Power Supply Removing the DC Power Supply Removing and Installing a DC Power Supply 10 Removing the Ground Lugs Installing the DC Power Supply Installing the DC Grounding Leads 11 Locating the DC Grounding Stud and Grounding Materials 12 Inserting the Terminal Block Plug in the Block Header Powering Off the Router and Removing the Cover Removing and Installing a Dimm 13 Removing the Cover Removing and Installing the Dimm 14 Removing and Replacing the Dimm To replace or upgrade the DIMM, follow these instructions 15 Inserting the Screws and Replacing the Cover Replacing the Cover and Powering On the Router Troubleshooting Overview Troubleshooting Initial Startup Problems Action Yes Online Troubleshooting Resources Identifying Startup Problems Problem Solving Using a Subsystems Approach Symptom Possible Cause Possible Solution Troubleshooting the Power Subsystem Symptom Possible Cause Possible Solution Chassis Troubleshooting the Cooling SubsystemCommand to display the internal chassis This error message indicates that the system has Troubleshooting the Processor Subsystem Troubleshooting the I/O Subsystem Router# format bootflash Upgrading the Boot Helper Boot Loader ImageTroubleshooting the Port Adapter or Service Adapter Enabled 7201boot# configure terminal Boot Prompt boot#Router# copy tftp bootflash 7201boot# copy tftp disk0 ROMmon Prompt rommon Rommon 2 boot disk0c7200p-js-mz Gigabit Ethernet interfaces 2045K bytes of Nvram Complete Boot Prompt and ROMmon Prompt Example Readonly Rommon initialized rommon 1 boot disk0c7200p-js-mz 7201# show version Last reload reason Reload Command Cleaning the Fiber-Optic Connections Cisco 7201 Router Specifications Description SpecificationAC-input power 150W maximum AC-input power typical 85W Power Supply Product Numbers Power Supply Product NumberAC power supply PWR-7201-AC= DC power supply PWR-7201-DC= Memory Size Product Number Processor and Memory SpecificationsSoftware Requirements Memory Type Size Quantity Description Total Sdram Quantity/Description Product ID SFP Module Specifications and ConfigurationsSpecification Description Memory Module Size Product Number SMF 100BASE-FXMMF 1000BASE-LX/LH TX Data Pin FE Signal GE SignalGigabit Ethernet RJ-45 Port Pinouts TX DATA+1 Rx D RX DataRx B Rx D+ DTE Router Cable Adapter End Device Gigabit Ethernet Flow Control Information Direction Description Console Port and Auxiliary Port Signals and PinoutsPin Signal Direction Description Pin Product Description Using the CompactFlash Disk Hardware and Software Requirements Tools and Parts RequiredCompatibility Requirements Boot Environment Variables Router show bootvarSystem Memory and Software Image Functions and Interactions Systemconfig# config-register Systemconfig# boot system flash disk0rsp-p-mz.12-0Systemconfig# boot config disk0configfile Systemconfig# boot bootldr bootflashc7200p-kboot-mz Sample Upgrade Process Working with a CompactFlash DiskThis section includes the following subsections Command and Arguments Purpose Software Command Overview Using Software Commands Using the cd Command Using the show CommandSystem# cd disk0 Using the pwd Command Using the dir CommandUsing the format Command Using the mkdir Command System# mkdir disk0dailydirDir Verify that the file fun1 is deleted Using the rmdir CommandUsing the delete Command Delete the file fun1 System# configure terminal Enabling Booting from a CompactFlash DiskSystemconfig# boot system flash disk0myfile Systemconfig# boot system flash disk0 myfile Press Ctrl-Zto exit configuration mode System# copy systemrunning-config nvramstartup-configCrtl-Z OL-11364-04 Configuration Bit Meanings Following information is found in this appendixBit No Hex Meaning Tftp flash filename Boot Field MeaningBoots the boot helper image as a system image Bits Action/File Name Bit Bit Baud Bit Bit 10 and BitBit 11 and Bit Bit IP Address net host Register + 02x100 At last boot Bit# Confreg Setting the Configuration Register While Running Cisco IOS Change Console baud rate? y/n n OL-11364-04 D E Alarm LED Configure memory command Specifications Show environment allCompactFlash Disk configurations A-3 Confreg Config-register command Related Documentation feedback Configure terminal commandConfiguring AppleTalk Enable password command IN-4 Slot numbering Logical interface numbering Product disposal Port adapter LED Status LED Show environment last Show environment table Voltage, monitoring USB LED