
|
|
|
|
| Chapter |
|
| 4.6 |
| “VA PCA Not OK” |
| /VA_OK is High (BAD). |
|
|
|
|
| |||
|
|
|
|
|
|
|
| 4.7 |
| “VP PCA Missing” |
| “No Slave Ack” status on first poll of VP. |
|
|
|
|
|
|
|
|
| 4.8 |
| “VP PCA Not OK” |
| VP_OK is High (BAD) |
|
|
|
|
|
|
|
|
| 4.9 |
| “RTG PCA Missing” |
| “No Slave Ack” status on first poll of RTG |
|
|
|
|
|
|
|
|
| 4.10 |
| “RTG PCA Not OK” |
| RTG_OK is High (BAD) |
|
|
|
|
|
|
|
|
| 4.14 |
| “Lamp Startup” |
| Lamp Failed to light (/LAMP_LIT_B not Low for 3 |
|
|
|
|
|
| seconds out of 20 seconds.) |
|
| 4.15 |
| “Low Voltage PS” |
| Low Voltage PS failed (/LV_OK_B is High). |
|
|
|
|
|
|
|
|
| 4.16 |
| “High Voltage PS” |
| High Voltage PS failed (/HV_OK_B is High). |
|
|
|
|
|
|
|
|
| 4.17 |
| “VIC1 Board Not OK” |
| /VIC_OK is High (BAD) on VIC Slot 1. |
|
|
|
|
|
|
|
|
| 4.18 |
| “VIC 2 Board Not Ok” |
| /VIC_OK is High (BAD) on VIC Slot 2 |
|
|
|
|
|
|
|
|
| 4.19 |
| “VIC3 Board Not OK” |
| /VIC_OK is High (BAD) on VIC Slot 3 |
|
|
|
|
|
|
|
|
| 4.20 |
| “VIC1 Invalid Type” |
| Software does not support VIC_ID in Slot 1 |
|
|
|
|
|
|
|
|
| 4.21 |
| “VIC2 Invalid Type” |
| Software does not support VIC_ID in Slot 2 |
|
|
|
|
|
|
|
|
| 4.22 |
| “VIC3 Invalid Type” |
| Software does not support VIC_ID in Slot 3 |
|
|
|
|
|
|
|
|
| 4.23 |
| “Shutters Missing” |
| One or more shutters not installed (BAD) |
|
|
|
|
|
|
|
|
| 4.24 |
| "Lamp Start Not On" |
| /LAMP_OK is high, lamp module not installed, jumper |
|
|
|
|
|
| missing, ALPS bad. |
|
| Most Category 6 error codes indicate RS232 communication errors and apply to Switchers only. |
| ||||
|
|
|
|
|
|
|
| 6.1 |
| “Sync Timeout” |
| No Header found in data stream - possible baud rate |
|
|
|
|
|
| error. |
|
| 6.2 |
| “No Char Repeat” |
| Expected data characters to be repeated - failed. |
|
|
|
|
|
|
|
|
| 6.3 |
| “Invalid Format” |
| Data not in Extron or JVC Switcher format. |
|
|
|
|
|
|
|
|
| 7.1 |
| “Write Len Error” |
| Ansi Output to RS232 port was interrupted - |
|
|
|
|
|
| incomplete. |
|
| 8.1 |
| “VIC Slot is empty” |
| User has selected a Channel - VIC is not present. |
|
|
|
|
|
|
|
|
| 8.2 |
| “VIC Type Changed” |
| User has selected a Channel - VIC type has changed. |
|
|
|
|
|
| User may have swapped a VIC into an incorrect slot. |
|
| 8.3 |
| “Interpol Blocked” |
| Software process error - Interpolation Process not |
|
|
|
|
|
| allowed to run by higher priority processes. |
|
| 9.1 |
| “Quad Dec Not Init” |
| HW: Quad Decoder failed Startup Sequence. |
|
|
|
|
|
|
|
|
| 10.1 |
| “Shutter Stat BAD” |
| One or more shutters reading wrong status. |
|
|
|
|
|
|
|
|
One other error may appear on the monitor screen with the statement “Assertion
Failed” (only if the PC is connected to Port A). This is a very rare but serious
Model 200 Service Manual |