14.3Listing of Global Messages
Error |
| Message | Description | Canceling and Re- | |
Code |
| pairing Method | |||
|
|
|
| ||
|
|
|
| ||
3051 | G22, G28, ... G31, G37 | If in block G22 incorrect address is found, | The message is can- | ||
|
|
|
| if in block G22 P is not 0 or 1, | celed by RESET |
|
|
|
| if in block G22 relation between the value | key. |
|
|
|
| of addresses X Y Z and I J K is incorrect, |
|
|
|
|
| if in block G22 reference was made to a |
|
|
|
|
|
| |
|
|
|
| if in block G28, G29, G30 address differ- |
|
|
|
|
| ent from axis address, addresses N, P, F, |
|
|
|
|
| M, S, T has been programmed, |
|
|
|
|
| if in block G30 P is not 1, 2, 3, 4, |
|
|
|
|
| if in block G31address different from axis |
|
|
|
|
| address, N and F has been programmed, |
|
|
|
|
| if in a block G37 0 displacement has been |
|
|
|
|
| programmed or more than one coordinate |
|
|
|
|
| has been referred to. |
|
|
|
|
| ||
3052 | ERROR IN G76, G87 | If drilling cycle G86.1 is programmed and | The message is can- | ||
|
|
|
| the facility of spindle orientation is not | celed by RESET |
|
|
|
| incorporated, or | key. |
|
|
|
| if a drilling cycle G87 is programmed, the |
|
|
|
|
| spindle can be oriented but cycle is in |
|
|
|
|
| state G99. |
|
|
|
|
| ||
3053 | NO BOTTOM OR R POINT | If in the canned cycle R point or bottom | The message is can- | ||
|
|
|
| (Z) point has not been defined. | celed by RESET |
|
|
|
|
| key. |
|
|
|
|
|
|
3054 | G31 | IN | INCORRECT | If in block G31 | The message is can- |
| STATE |
| state G16 is on, | celed by RESET | |
|
|
|
| if state G41 or G42 is active, | key. |
|
|
|
| if one of the transformations (G51, G51.1, |
|
|
|
|
| G68) is on, |
|
|
|
|
| if the state G16 or G95 is active. |
|
|
|
|
|
|
|
3055 | G37 | IN | INCORRECT | If in block G37 | The message is can- |
| STATE |
| state G16 is on, | celed by RESET | |
|
|
|
| if length offset G code (G43, G44, G49) | key. |
|
|
|
| has been programmed, |
|
|
|
|
| if one of the transformations (G51, G51.1, |
|
|
|
|
| G68) is on. |
|
|
|
|
|
|
|
3056 | LIMIT |
|
| If parameter 3163 CHBFMOVE is set to 1 | The message is can- |
|
|
|
| and the end position of programmed block | celed by RESET |
|
|
|
| exceeds the overtravel limit specified by | key. |
|
|
|
| parameter. |
|
|
|
|
| ||
3057 | FORBIDDEN AREA | If parameter 3163 CHBFMOVE is set to 1 | The message is can- | ||
|
|
|
| and the end position of the programmed | celed by RESET |
|
|
|
| block is in the forbidden area specified by | key. |
|
|
|
| instruction G22. |
|
|
|
|
| ||
3058 | NOT IN DNC | If during DNC machining command M99 | The message is can- | ||
|
|
|
| P, GOTO or WHILE...DO occur in main | celed by RESET |
|
|
|
| program. | key. |
