Messages of custom macros | NCT Group NCT 2000T, NCT 100T, NCT 990T

14 Listing of Messages and their Codes

Messages of custom macros:

–error messages programmed by the user and waiting for to be canceled, or

–messages programmed by the user waiting for START.

In the case of global messages the different messages are needed to be answered differently, i.e., to be canceled. Therefore, in the enclosed table after each message the method of cancel- ing it is shown. These may be as follows:

Canceling message by means of turning power off and on

In case of extremely serious or dangerous alarms the message cannot be canceled, the NC must be restarted. These messages cut the machine off the NC and create emergency stop (EMG) state every time.

Canceling message by means of pressing RESET key

This is the general mode of canceling error messages. By the use of the RESET key the

automatic execution is interrupted. If thereafter the START button is pressed, the NC pre- processes the block and if the error has been repaired successfully it also re-executes the block. In case of extremely serious or dangerous alarms the message cuts the machine off the NC, creates emergency stop (EMG) state and deletes the reference point. After using the RESET

button, the machine can be turned on. Than the machine must be returned to the reference point.

Canceling message by means of pressing START button

As the effect of certain messages displayed by the PLC program or custom macro messages written by the user the control assumes STOP state and waits for the operator’s intervention in accordance with the message. After the wished operation has been done by the operator the

machining is continued by means of START button .

Canceling message by means of operator’s intervention

Certain messages can only be canceled by ceasing the reason of their appearance. This is the situation in the case of message LIMIT X+, which can only be canceled, if the limit switch is left behind by moving in negative direction in a manual mode.

122

Image 122

NCT Group NCT 2000T, NCT 100T, NCT 990T manual Messages of custom macros

Contents

NCT 100T NCT 990T NCT 2000T Mailnct@nct.hu Contents Intervention in the Course of Program Execution Interruption and Restart of Automatic Operation Page Introduction Conditions of Operation and Storage Operator’s Panel NC Control Panel Display Unit and Data Input Keyboard Operator’s Panel Action menu key Data Input KeyboardScreen menu key Backspace Keys PgUp State of First Operation Mode GroupState of Second Operation Mode Group PgDn Interpolator State Functional State of Automatic and Manual Data InputProgram Manipulation State PLC State Indication of Ready Status of Control Machine Control Board Operation mode selectors Automatic Manual data input Override switchesSwitches modifying the conditions of program execution Increment selectors Block restart Block return Function lock Movement, start and stop buttons Position General Operating KnowledgeScreen Menu Offsets CheckProgram Graphics #100 SettingService Action Menu General Operating Knowledge General Displaying Areas and Actions Executed on Them Position Screens Actions of Position Screens Function Screen, Subprogram and Macro Levels Check ScreensProgram Text Screen, Listing of Running Program Last and Active screens. G Codes and Compensations Actions of sreens Program TEXT, FUNCTION, Last and Active Key OPERATOR’S Panel ScreenActions of OPERATOR’S Panel Screen Increment Actions Incr Operation Modes Actions ModesAxes Actions Actions Clear Relative Position Actions Clear Relpnt Messages Screen Directory Screen Program ScreensScreens of actions executed on part programs Actions of Directory Screen Program Screens View Screen Actions of View Screen Edit Screen Actions of Edit Screen Block Input Screen Actions of Block Input Screen Actions of Work Offsets Screen Offsets ScreensWork Offsets Screen Tool Offsets Screen Keys This bar selects the offset register to be modified Actions of Tool Offsets Screen Offsets Screens Work Offset Measure Screen Actions of Work Offset Measure Screen Tool Length Offset Measure Screen Actions of Tool Length Offset Measure Screen Relative Position Offsets Screen Actions of Relative Position Offsets Screen Graphic Position Screens Graphic Parameters Screen Actions of Graphic Parameters Screen Color Code Draw Screen Actions of Draw Screen Graphic Position Screens Actions of Local Macro Variables #1-#33 Screen Setting ScreensScreen of Local Macro Variables #1-#33 Screen of Common Macro Variables #100-#199 Actions of Common Macro Variables #100-#199 Screen Screen of Common Macro Variables #500-#599 Actions of Common Macro Variables #500-#599 Screen Tool POT Table Screen Timer and Counter ScreenActions of Timer Counter Screen Actions of Tool POT Table Screen PLC Table Screen Actions of PLC Table Screen USER’S Parameters Screen User’s Params Actions of USER’S Parameters Screen Fix code, or PLC key Security Panel ScreenGenerated code, or PLC key Below table contains the codes of the appropriate functions Setting Screens Editing Part Programs Structure of Part Program Beginning and end of program Division of Edit Screen during Editing Typing Moving the cursor Insert Selected text is deleted by means of key del Edit Actions Undo, Cut, Copy, Paste, Find and Replace Editor Action MenuFile Actions Save, Save as Edit Editing part programs Insert Condition Action Group Insert ActionsInsert Miscellaneous Action Group Insert Operation Action Group Help Switching Over Operation Modes Tion menu key Axis Selection Manual Reference Point Return ModeManual Operation Modes Types of Reference Point Return Jog Mode Feedrate Selection Jog Mode Incremental Jog Mode Increment Selection Incremental Jog Mode Manual Handle Mode Speed Work Zero Point Offset and Tool Length Offset Measurement Actions Executed in Manual Operation ModesSingle Block Operation Work Zero Point Offset Measurement Coordinate system to be measured can be selected after Work Zero Point Offset Measurement Work Zero Point Offset Measurement Tool Length Offset Measurement inside the Machine Tool Length Offset Measurement inside the Machine Automatic Tool Length Offset Measurement CONTACTX+ Contactx CONTACTZ+ Calibrating Tool Offset Sensor Calibrating the Sensor to the Coordinate System of Chuck Procedure can also be applied for the other buttons Calibrating the Sensor to Reference Point Program Execution in DNC Automatic ModeModes of Automatic Operation Machining Start and Stop Edit Mode Editing Programs under Automatic Execution Manual Data Input Mode Differences between Automatic and Manual Data Input modes Manual Data Input Mode Override Switches Feedrate Override Switch Rapid Traverse Override Switch Spindle Speed Override Switch Override Switches Starting Program Execution ResetProgram Execution Start and Stop Feed Stop Programmed Stop M00 Conditional Stop M01 End of Program M02, M30 Increasing Feedrate by Means of Rapid Traverse Jog Button Intervention in the Course of Program ExecutionConditional Block Skip Rules of operation are as follows Effect of intervention to coordinate system Dry Run All Feedrates at High Speed Debugging the Part ProgramSingle Block Execution Function Lock Machine Lock FunctionOther Locking Possibilities Axis Lock Test Run Interruption and Restart of Automatic Operation Interruption of Automatic Operation Restore Modal FUNCTIONS? N Is displayed Y=yes. By pressing Shift key question Program No Unconditional Restart of Automatic OperationInterrupting Single Blocks Interrupting Canned Cycles Interrupting Machining in Offset Mode 105 G41 Unconditional Restart of Automatic Operation Return to Block Start Position in Automatic Mode Automatic Operation Restart with Block Restart Condition Automatic Operation Restart with Block Restart Condition Automatic Operation Restart with Block Restart Condition Block Restart Automatic Mode Restart with Block Return Condition Return to the Interruption Point in Automatic Operation Cases of Return by Means of Condition Block Return Automatic Mode Restart with Block Return Condition When condition Block Return Automatic Operation Start after Block Search If F4 Block Search action is selected after pressing action 117 Command SearchNumber of Tool to be Change d T1 Other Functions M Spindle Rotation Code M3Coolant Code M8 Positions Search for Interrupted Block Command GotoOther Intervention Possibilities Before Start 120 Local Message Listing of Messages and their CodesThere may be two types of messages Local and global Global Messages Messages of custom macros Listing of Global Messages 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 3103 1383102 3104 139 140 141 142 143 FEEDBACKn 124 Alphabetical indexENCODERn 124