AlrmRelay Disab Next Enab Disab Prev | Paradyne 316x manual

Configuration Options

Table C-8

(3 of 3)

Alarm Configuration Options

Err Rate: 10E-4

Next 10E-4 10E-5 10E-6 10E-7 10E-8 10E-9 Prev

Excessive Error Rate Threshold. Sets the error rate threshold that determines when an Excessive Error

Rate (EER) condition is declared. This rate is determined by the ratio of the number of CRC6 errors to the total number of bits received over a set period of time.

Select from the following:

•10E-4. EER is declared if more than 1,535 CRC6 errors are detected within 10 seconds (factory default).

•10E-5. EER is declared if more than 921 CRC6 errors are detected within 60 seconds.

•10E-6. EER is declared if more than 92 CRC6 errors are detected within 60 seconds.

•10E-7. EER is declared if more than 9 CRC6 errors are detected within 60 seconds.

•10E-8. EER is declared if more than 41 CRC6 errors are detected in three 15-minute intervals.

•10E-9. EER is declared if more than 4 CRC6 errors are detected in three 15-minute intervals.

AlrmRelay: Disab

Next Enab Disab Prev

Alarm Relay. Specifies whether an alarm condition for this circuit card will activate the shared alarm relay on the

3000 Series Carrier. The alarm deactivates when the condition(s) causing it is corrected. An Alarm Cut-Off issued from the SDCP (or PC Emulation program) for a particular 3161 DSU/CSU also deactivates the alarm. The 3161 DSU/CSU will not reactivate the alarm relay until all alarm conditions for the unit are cleared.

The following alarm conditions will activate the alarm relay when this configuration option is enabled:

•Continuous Loss of Signal (LOS) or Out of Frame (OOF) at either the NETWORK or DTE T1 interface.

•Alarm Indication Signal (AIS) received at either the NETWORK or DTE T1 interface.

•Yellow alarm signal received at either the NETWORK or DTE T1 interface.

•Excessive Error Rate (EER) detected at the NETWORK T1 interface.

NOTE: This configuration option is only displayed for Model 3161 DSU/CSUs.

3160-A2-GB22-10

December 1996

C-19

Image 160

Paradyne 316x manual Err Rate 10E-4 Next 10E-4 10E-5 10E-6 10E-7 10E-8 10E-9 Prev, AlrmRelay Disab Next Enab Disab Prev

Contents

Channel Service Unit Includes Terminal User Interface Warranty, Sales, and Service Information TrademarksOperators Guide 3160-A2-GB22-10 Copyright E 1996 Paradyne Corporation. All rights reserved Important Safety Instructions CC DGD D C D CC United States Government Requirements and Equipment Return316x DSU/CSU Facility Interface Codes Description Canada Government Requirements Table of Contents Glossary Index List of Figures LCD Slide Latch Adapter Cable Feature Number 3100-F1-560 Models 3160/3614 DSU/CSUs Rear Panel Connectors List of Tables Acculink 316x DSU/CSU Preface Objectives and Reader AssumptionsRelated Documents Reference Documents Introduction Overview Features Alarm InterfaceIntegral Modem User Interface Front Panel Access Control Feature Front Panel EmulationFront Panel Pass-Through Async Terminal Interface Support Acculink 316x DSU/CSU Physical Description Standalone Model 3160/3164 DSU/CSUs3160/3164 DSU/CSU Front Panel 3160/3164 DSU/CSU Rear Panel DSU/CSU Front Panel LCD DSU/CSU Rear Panel Connector Name Models 3160/3164 DSU/CSUs Rear Panel ConnectorsFunction Model 3161 Front Panel Functions Carrier-Mounted Model 3161 DSU/CSUModel 3161 DSU/CSU Rear Panel Auxiliary Backplane Installation Planning Network Fractional T1 Serial Connection to Snmp Box Contents Quick Start Procedure Optional Power Selection Installing the +24 Vdc Power Supply Installing the Single ±48 Vdc Power Supply ±48 Vdc Single Source Power Supply Pinouts Installing the Redundant ±48 Vdc Power Supply ±48 Vdc Redundant Source Power Supply Pinouts Power-Up Self-Test DSU ESF Selecting a Model DSU/CSU IdentityStatus DevHS STest Perf Status TStat LED ID Control Reset CID Password Identity Ser=xxxxxxxIdentity Mod=xxxx-xx-xxx Identity Cust ID=xxxxxxxx Establishing Access Security on a Port Setting/Changing a Password Control Reset CID Passwd Passwd Up Down Save 3160/3164 DSU/CSU Cabling 13 /3164 DSU/CSU Cabling Configurations Factory Default Configuration Options Installing Front Panel Emulation Software Enabling/Disabling the Front Panel 3160/3164 DSU/CSU User Interface Access Security Changing User Interface Access Security Security Lvl1 Lvl2 Operation LCD Acculink 316x DSU/CSU Operating the Front Panel Model 3161 DSU/CSU Faceplate Device Health and Status Messages Other DisplaysContext-Sensitive Menu Keypad LEDs LEDs System LEDs Name Color Meaning Network Interface LEDs SIG DSX-1 Drop/Insert Port LEDs PDV Data Port LEDs DTR Displaying LED Conditions on the Front Panel DTR TXD Selecting the DSX-1 or a Port for LED Display LED Dsply DTEDTE Prt1 Prt2 Front Panel Emulation on a PC LED Display Selection Screen Test Jacks Front Panel Emulation Screen Icons Name Meaning 12 DSU/CSU Test Jacks Configuring the DSU/CSU Configuration Option AreasConfiguration Options Test Jack Functions Configuration Procedures 14. Configuration Branch for the Front Panel Displaying/Editing Configuration Options 15. Configuration Branch for the Async Terminal NET Framing ESF Next D4 ESF 16. Load From Screen Saving Edit Changes Save Edit to Activ Cust Selecting a Specific Port Selecting/Copying to a Specific PortPort Select Copy Prt1 Prt2 Prt1 Value Options Prt2 Value OptionsPrt3 Value Options Prt4 Value Options Copy From Prt1 Prt2 Prt3 To Copy to One or All PortsCopy To All Prt1 Prt2 Configuring the 3160/3164 DSU/CSU for Snmp Management Selecting the Port Modem Use Next Snmp Ascii Setting the IP Address Com Use Next Snmp Ascii Edit User Alarm Snmp Config Gen TrapSnmp System Name Next Edit Clear 000.000.000.000 Up Down Save Selecting the Link Layer Protocol010.155.111.222 Up Down Save Specifying the Community Names and Access Types Modem Link Next PPP Slip CommunityName1 Next Edit Clear Public Up Down Save Access Next Read R/W Snmp TrapsNewname Up Down Save Enterprise-Specific Trap Definitions Trap Value Event Selecting the Number of Trap Managers Num Trap Mgrs1 Next Configuring an IP Address for Snmp Trap Manager 23. Trap Options Screen Configuring DS0 Channels Trap n IP Adr Next Edit Clear 24. Example Channel Allocation Network T1 Interface Network Channel Allocation 25. Example Interface Tables DTE Chan Assign Voice Config N1 ± RBS or Data 26. DS0 Channels Containing RBS Information Worksheet Port Chan Options Value Conf NET, DTE Port Chan Options Value Conf Display Channel Symbols Meaning Channel Config Dsply Clear DTEDisplaying DS0 Channel Assignments Edit Port NET Chan NET DTE Display ChanPrt1 Allocating Data Ports Block Channel Assignment Method Example NET Acami Channel Assignment Method Example Port Rate384 Next 64Start AtClear Next Clear N1 Assign ByACAMI Next Block Acami Individual Channel Assignment Method Example Assign ByChan Block Acami ChanAssign ByChan Next Block Acami Next Prt1 Prt2 DTE Channels Assign Voice 30. DTE Assignment Screen RBS Clearing DS0 Channel Allocation Clear Channel 32. Common Clocking Configurations Timing Configuring for Network Timing Example Edit NET Chan GenGenYellowEnab Next Enab Disab Clock SrcNET Next NET DTE Clock SrcNET Prt1 Int Ext Configuring for External Timing ExampleClock Rate1544 Next 2048 101 Selecting the Shared Communication PortSelf±TestEnab Next Enab Disab Device Health and Status Checking the StatusMasterComDisab Next Enab Disab Message Health and Status MessagesDescription Displaying Device Health and Status Self-Test HealthDevice H/S OOF at DTE Auto Dev H/S OOF at DTE Displaying Self-Test Results Self-Test Health MessagesMessage Description STest Health Passed CurTimer Performance ReportEvent=xx,xxx VldIntvl=xx 35. Carrier Telco and User Register Organization StEvnt Displaying User Performance Registers Clearing User Performance Registers 36. Telco Performance Report Screen Controlling the DSU/CSU LED Acquiring/Releasing the Active Physical Interface Acquiring the Active Physical InterfaceReleasing the Active Physical Interface DSU Fmt Initiating a Call for Front Panel Pass-Through Operation Using the Integral ModemFt. Panel Released Pass n Up Down Dial Call Setup Pass Dial ChDirDial n Up Down Dial Entering a Password to Gain Access Passwd Up Down Done Disconnecting the Modem Connection Disconnecting Using the Disconnect CommandDisconnecting Using Front Panel Keys Call Setup Disc ChDir Entering Numbers in the Phone Directories Xxxxxxxxxxxxxxxxx Next Prev Edit Xxxxxxxxxxxxxxxxx Up Down Save Valid Phone Number Characters Meaning Restrictions Deactivating the Alarm Relay Alarm Cut-Off Command CompleteStarting Front Panel Emulation Control ACO Rel LED Using the Async Terminal Feature Setting Interface Options Entering a Password Activating Interface Option ChangesInitiating an Async Terminal Session Async Terminal Menus and Screens Menu Selection Screens Edit and Display Screens Hard-Key Representations for Edit Screens Usage Function Representations for Edit Screens Function Key Usage Terminating a Session Maintenance Troubleshooting Alarms Snmp TrapsSnmp Trap per Interface Interface Snmp Trap Meaning Test Commands Test Branch Remote Loopback Tests Sending a Line Loopback Up or DownTest Rlpbk Lpbk Ptrns Rem Loopback Local Loopback Tests Sending a V.54/ANSI FT1 Activation/DeactivationRem Loop Type Prt1 Prt2 Prt3 Valid Loopback Combinations Starting a Line LoopbackLoopback Abort LLB PLB Starting a Payload Loopback Starting a DTE Loopback Loopback Starting a Repeater LoopbackLLB PLB DLB Starting a Data Channel Loopback PLB DLB RLBDLB RLB Dclb Loopback Dclb Prt1 Prt2 Prt3 RLB Dclb Dtlb Starting a Data Terminal LoopbackLoopback Dtlb Prt1 Prt2 Prt3 DTE-initiated Loopbacks Aborting LoopbacksLoopback Abort All LLB PLB Test Patterns Sending Test Patterns Monitoring Test Patterns 8 Network PortPatterns Mon Qrss Monitor Name NET Prt1 Prt2 Aborting Test Patterns Lamp TestStarting a Lamp Test Patterns Abort All Send Mon Aborting a Lamp Test Test Lpbk Ptrns LampLamp Test Abort Start 0123456789 = ? Displaying DSU/CSU Test Status Test Status Messages Downloading Software Resetting the DSU/CSUStatus STest Perf TStat Control ClrUsr Reset Device Reset Yes No Front Panel Menu a 3160-A2-GB22-10 Front Panel Menu Technical Specifications B Power Requirements Clocking Sources Power Consumption Dissipation Pounds .82 kg Configuration Options C Functional Grouping Table C-1 DTE Interface Configuration Options DTE Interface Configuration OptionsContext-Sensitive Menu Extrn DLB Disab Next Enab Disab Prev Send Ones Enab Next Enab Disab Prev Port Configuration Options Port Configuration OptionsTable C-2 Port Type E530 Factory Next E530 V.35 RS449 Prev All Ones Both Next Disab DTR RTS Both Prev Table C-2 Port Configuration OptionsRcv Yellow Halt Next None Halt Prev Invert TxC Disab Next Enab Disab Prev Tx Clock Int Next Int Ext PrevInvert Data Disab Next Enab Disab Prev Network Interface Configuration Options Table C-3 Network Interface Configuration Options NET PLB Enab Next Enab Disab Prev Bit Stuff Next 62411 Part68 Disab Prev Channel Configuration Options Table C-4 DTE Channel Configuration Options Table C-5 Data Port Channel Configuration Options Start At Clear Next N10 N11 N24 Prev D10 D11 D24 N10 N11 N12 N24 Next Prev D10 D11 D12 D24 General Configuration Options Table C-6 General Configuration OptionsGen Yellow Enab Next Enab Disab Prev Clock Src NET Next NET DTE Prt1 Int Ext Prev User Interface Configuration Options Table C-7 User Interface Configuration Options MasterComDisab Next Enab Disab Prev Com Use Ascii Next Snmp Ascii Term PrevCom Type Async Next Async Sync Prev Com Clk Int Next Int Ext Prev Com Rate Next 1.2 2.4 4.8 9.6 14.4 19.2 Prev Char Length Next 7 8 PrevCParity None Next None Even Odd Prev CStop Bits Next 1 1.5 2 Prev Modem Type Async Next Async Sync Prev Modem Rate Next 1.2 2.4 PrevMChar Len Next 7 8 Prev MParity None Next None Even Odd Prev Alarm Configuration Options Table C-8 Alarm Configuration OptionsAlrm Msg Disab Next Disab Modem Com Both Prev Snmp Trap Disab Next Enab Disab Prev Dial Delay Next 1 2 3 4 5 6 7 8 9 10 Prev DialOut Disab Next Enab Disab PrevCall Retry Disab Next Enab Disab Prev Next None 1 2 3 4 5 Prev Err Rate 10E-4 Next 10E-4 10E-5 10E-6 10E-7 10E-8 10E-9 Prev AlrmRelay Disab Next Enab Disab Prev Snmp Configuration Options Table C-9 General Snmp Configuration Options Access 2 Read Next Read R/W Prev Com IP Adr Clear Next Edit Clear PrevCom Link PPP Next PPP Slip Prev Modem IP Adr Clear Next Edit Clear Prev Table C-10 Snmp Trap Configuration Options Num Trap Mgrs Next 1 2 3 4 5 6 PrevTrap n IP Adr Clear Next Edit Clear Prev Gen Trap Both Next Disab Warm Auth Both Prev Link Trap Both Next Disab Up Down Both Prev Trap I/F All Next NET DTE T1s Ports All Prev Pin Assignments D T1 Network Connector InterfaceCables Receiver Ring Receiver Tip Transmitter Ring Transmitter Tip RJ48C DA15P DSX-1 Port DTE Interface Integral Modem Service Port Interface AUX Port Interface Figure D-5. COM Port-to-PC Cable Feature Number 3100-F1-550 COM Port Interface Acculink 316x DSU/CSU Table D-7 EIA-530A Port Interface Connector Signal Circuit EIA-530A DB25 Port Interface ConnectorDirection Pin Mnemonic Number RS449 Port Interface Connector Table D-8 RS449 Port Interface Connector Signal Circuit Pin Assignments Table D-9 Port Interface Connectors Signal Port Interface ConnectorDirection Pin Number Pin Assignments Power Input Connector Power CableTable D-10 DC Power Connector Signal Pin Number External Clock Connector Figure D-11. The connector information is in Table D-12 Slide Latch Adapter Snmp MIB Objects E Management Information Base MIB II RFC System Group Supported System Group ± ªsysServicesº Object system System Group, MIBSystem Group ± ªsysDescrº Object system System Group ± ªsysObjectIDº Object system Interface Group, MIB Interface Group ± ªifDescrº Object ifEntryInterface Group ± ªifTypeº Object ifEntry Interface Group ± ªifMtuº Object ifEntry Interface Group ± ªifAdminStatusº Object ifEntry DTE IP Group ± ªipNetToMediaTableº Object ip Icmp Group, MIBUDP Group, MIB IP Group, MIB DS1/E1 MIB RFC Near End Group ± ªdsx1LineStatusº Object dsx1ConfigEntry Near End Group ± ªdsx1SendCodeº Object dsx1ConfigEntryNear End Group ± ªdsx1SignalModeº Object dsx1ConfigEntry Near End Group ± ªdsx1Fdlº Object dsx1ConfigEntry RS-232-like MIB RFC Near End Group ± The DS1 Total Table Objects dsx1TotalEntryFar End Group, DS1/E1 MIB DS1 Fractional Group, DS1/E1 MIB Number of Ports ± ªrs232Numberº Object rs232 General Port Table, RS-232-like MIBGeneral Port Table ± ªrs232PortIndexº Object rs232PortEntry General Port Table ± ªrs232PortTypeº Object rs232PortEntry Input Signal Table, RS-232-like MIB Input Signal Table ± ªrs232InSigNameº rs232InSigEntryInput Signal Table ± ªrs232InSigStateº rs232InSigEntry Input Signal Table ± ªrs232InSigChangesº rs232InSigEntry Output Signal Table ± ªrs232OutSigNameº rs232OutSigEntry Output Signal Table ± ªrs232OutSigStateº rs232OutSigEntryOutput Signal Table ± ªrs232OutSigChangesº rs232OutSigEntry Generic-Interface MIB Extensions RFC Acculink 316x DSU/CSU Table F-1 Troubleshooting Symptom Possible Cause Solutions Troubleshooting Table FYellow at Net AIS at Net Yellow at DTEAIS at DTE Configuration Worksheets G DTE Net Value Options Configuration Worksheets Network T1 Interface Network Channel Allocation D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D25 Acami Port Chan Options Value Conf Alarm Value Options General Options ValueUser Options Value Snmp Gen Value Options Equipment Feature Number Equipment List HPEC Code Cable numbers for DSU/CSU are located Glossary AIS EER Index DTE Index Index-4