Electro-magnetic compatibility EMC | Siemens 420 specification

Issue 07/04

7 Electro-magnetic compatibility (EMC)

7 Electro-magnetic compatibility (EMC)

This Chapter contains:

EMC information.

7.1

Electro-magnetic compatibility (EMC)

168

MICROMASTER 420	Operating Instructions
6SE6400-5AA00-0BP0	167

Image 167

Siemens 420 manual Electro-magnetic compatibility EMC, This Chapter contains

Contents

User Documentation Operating Instructions Issue 07/04 Parameter List Micromaster 420 DocumentationGetting Started Guide Operating Instructions Valid for Release Operating Instructions Micromaster Central Technical Support Online Service & SupportUser Documentation Information is also available from Regional Contacts Qualified personnel Use for intended purpose only General Safety Instructions Commissioning Transport & Storage Dismantling & Disposal OperationRepair Safety Instructions Issue 07/04 Table of Contents 154 151152 153 List of Illustrations OFF1 List of Tables Table of Contents Issue 07/04 This Chapter contains Overview Micromaster Performance Characteristics FeaturesMain Characteristics Options Protection characteristics Installation Installation Issue 07/04 Ambient operating conditions Installation after a Period of StorageTemperature General Shock and Vibration Installation and coolingHumidity Altitude Mechanical installation Removing the Inverter from the rail Mounting on standard rail, Frame Size aFitting the Inverter to a 35 mm standard rail EN Inverter must always be grounded Electrical installation Operation with long cables GeneralOperation with ungrounded IT supplies Operation with Residual Current Device Access to the power and motor terminals Power and motor connections Three Phase Single Phase Terminal Designation Function Control terminals Action to Take Avoiding Electro-Magnetic Interference EMI Screening without a Gland Plate Screening MethodsGland Plate Installation Issue 07/04 This Section includes the following Functions Functions Issue 07/04 Issue 07/04 Functions Notation Setting / monitoring parameters and parameter attributesSetting parameters Parameters Monitoring parameters Attribute Description Group Inverter Rated motor current P03053 P0003 = P0003 =P0004 = Significance / command source Interconnecting signals Bico technology Main setpoint source Supplementary setpoint source Significance Command source Selection of command/frequency setpoint P0719 Bico technology BI Binector Input, signal receiver P parametersBO Binector Output, signal source r parameters Abbreviation and symbol Name Function CO Connector Output, signal source r parameters CI Connector Input, signal sink P parameters P0731 = P1070 =P0840 = P2051 = Parameter Designation Value 100 % Units Reference quantitiesInterface 100 % Example Description of the BOP Basic Operator Panel Operator panels for Micromaster Description of the AOP Advanced Operator Panel Operator Function Effects Panel/key Keys and their functions on the operator panel BOP / AOP Step Result on the display Changing parameters using the operator panelChanging P0004 parameter filter function External 24 Block diagram Parameter Function Factory setting 13 Recommended wiring for the factory setting Commissioning 14 Procedure when commissioning Check list 15 DIP switch to change-over between 50/60 Hz 1 50/60 Hz setting Commissioning parameter Factory setting User access levelQuick commissioning Parameterizing the drive with BOP or AOP Rated motor voltage Europe kW, frequency default 50 HzRated motor power Europe/ North America Selection of frequency setpoint Selection of command sourceControl mode End of quick commissioning/ drive setting 17 Example of a typical motor rating plate Nema Motor IEC Motor 19 Star / delta circuit configurations Hz characteristic 87 Hz Calculating the motor / control data Motor data identification stator resistance Motor data identification routine Ambient motor temperature entered in CPower-up the motor Disabled Serial Interface USS Commissioning the applicationAdapting the drive inverter to the application Digital input DIN 5.2 Selection of command source Selection of frequency setpoint Digital output Dout5.5 5.7 Analog output DAC Analog input ADC Fixed frequency FF Motor potentiometer MOP Ramp-function generator HLG 5.10 JOG Motor control Reference/limit frequencies Slip compensation entered in % Acceleration boost entered in %Starting boost entered in % Programmable V/f freq .0 Hz coord Inverter/motor protection Holding brake Inverter-specific Functions Flying startAutomatic restart PID controller DC brakingCompound braking Vdc controller Parameter Parameter text Example Max. value for PID feedbackSets lower limit for the PID controller output in % Example MM4 Series commissioning Issue 07/04 Functions Factory reset Parameter reset to the factory settingReset to the factory setting Digital inputs DIN Inputs / outputs Parameter value Significance P0701 P0703 digital inputs 1-3 or P0707 P0703 analog inputExample Bico parameterization Digital output Dout 11 Parameter P0731 frequently used functions / states ADC channel Analog input ADC 26 Wire breakage monitoring Wire breakage monitoring Analog output DAC 27 Signal output through the DAC channel Starter USS Communications COM link interface CB on COM link USS on COM link BOP link interface BOP on BOP link USS on BOP link USS at the COM link RS485 30 RS485 Terminator USS bus configuration via COM link RS485 Direct selection Fixed frequencies FF Direct selection + on command R0722.1 Binary-coded selection + on command Selecting via serial interfaces Motorized potentiometer MOP AOP at the BOP link Selecting via BOP or AOPParameters / keys 35 JOG counter-clockwise and JOG clockwise 10 JOG 105 36 Structure of the technological controller PID controller PID controller technological controller Parameterizations PID motorized potentiometer Motorized potentiometer PID motorized potentiometer PID-MOP PID fixed setpoint PID-FF Summation and modification of the frequency setpoint AFM Setpoint channel 111 With rounding Ramp-function generator RFG P1134 = P1132 P1133 Parameter Description 19 Bico parameters for ramp-function generator OFF1 12.3 OFF/braking functions OFF2 Manual / automatic operation Parameter setting Command source Value Command source Setpoint source On / OFF1/OFF3 Motor holding brake MHB 49 Motor holding brake after OFF2 On / OFF2 121 14.1 DC braking Electronic brakes 51 DC braking after OFF1 / OFF3 Sequence ➀ 52 DC braking after external selection Sequence ➁ 53 Compound braking Compound braking 126 Blackout Brownout Automatic restartLine undervoltage brownout Line failure blackout 128 Flying restart active Search direction Flying restart 130 Cause Closed-loop Vdc controlVdcmax controller DC link undervoltage 132 General monitoring functions / messages Monitoring functions / messages Functions / states Function chart Thermal motor model FeaturesThermal motor protection and overload responses 136 Temperature Classes 19.2 PTC temperature sensor 58 Connecting a temperature sensor to Micromaster General overload monitoring Power module protectionFault and shutdown I2t monitoring Heatsink temperatureThermal monitoring functions and overload responses Reducing the output frequency P0290 = 0,2 Reducing the pulse frequency P0290 = 2Disadvantage No reduction P0290 = 21.1 Control Open-loop/closed-loop control technique Use / property 27 V/f characteristic parameter P1300 Parameter Voltage boost Explanation Voltage boost 146 21.1.2 V/f open-loop control with flux current control FCC 62 Slip compensation Slip compensation 63 Effect of V/f resonance damping 21.1.4 V/f resonance damping Imax controller setpoint Current limiting Imax controller Troubleshooting Troubleshooting Issue 07/04 Troubleshooting with the SDP Troubleshooting with the BOP Alarm messages Fault messages and alarm messagesFault messages Suppressing fault / alarm messages 156 Micromaster 420 specifications Feature Specification Micromaster 420 specifications Issue 07/04 KHz 10 kHz 12 kHz 14 kHz 16 kHz Lbs 2AB11 2AB12 2AB13 2AB15 2AB17 2AB21 2AB22 2AB231BA1 5BA1 Awg Input voltage range AC 200 V 240 V, ± 10 % Unfiltered2UC11 2UC12 2UC13 2UC15 2UC17 2UC21 2UC22 2UC23 KVA 2UC25 2UC12 2UC131BA1 5BA1 2BA1 2BA1 0BA1 2AD23 2AD242AD31 2UD25 2UD27 2UD31 Input voltage range AC 380 V 480 V, ± 10 % Unfiltered2UD13 2UD15 2UD17 2UD21 2UD22 2UD23 2UD24 Device-dependent options OptionsDevice-independent options Options Issue 07/04 Electro-magnetic compatibility EMC EC type examination certificate Electro-magnetic compatibility EMCSelf-certification Technical construction file EMC Directive Compliance with Imminent Harmonics Regulations EMC Phenomenon Standard Level Classification of EMC performanceClass 1 General Industrial Class 2 Filtered Industrial 171 Class Model RemarksClass 1 General Industrial Appendices Changing the OperatorPanel Removing Covers Frame Size a Removing Covers 6SE6400-5AA00-0BP0 Removing ‘Y’ Cap Frame Size a Removing ‘Y’ Cap Issue 07/04 Removing ‘Y’ Cap Removing fan, Frame Size a Removing fan Removing fan, Frame Sizes B and C Applicable Standards COM List of Abbreviations List of Abbreviations Issue 07/04 PPO Index Issue 07/04 Index Ungrounded IT supplies Suggestions Corrections Suggestions and/or Corrections 188 Frame Size B & C View of Unit Frame Size a Siemens Aktiengesellschaft