87 Hz | Siemens 420 specs

3 Functions

Issue 07/04

Table 3-8		Example 1LA7060-4AB10

			Delta circuit	87 Hz	Star circuit
			configuration	characteristic	configuration
P0304		Rated motor voltage	230 V	400 V	400 V

P0305		Rated motor current	0.73 A	0.73 A	0.42 A

P0307		Rated motor power	120 W	207 W	120 W
P0308		Cos ϕ	0.75	0.75	0.75
P0310		Rated motor frequency	50 Hz	87 Hz	50 Hz

P0311		Rated motor speed	1350 RPM	2460 RPM	1350 RPM

P0314		Motor pole pairs	2	2	2

Contrary to the BOP, AOP operator panels or commissioning tool program DriveMonitor, the STARTER commissioning (start-up) program offers a mask- orientated quick commissioning, which is especially advantageous for users who are using MICROMASTER for the first time. On the other hand, BOP, AOP and DriveMonitor offer, in conjunction with the drive inverter, parameter-orientated quick commissioning where the user is navigated through the menu tree mentioned above.

NOTE

The MICROMASTER series of drive units is not available for 3-ph. 690 V AC.

MICROMASTER 420	Operating Instructions
68	6SE6400-5AA00-0BP0

Image 68

Siemens 420 manual 87 Hz

Contents

Operating Instructions Issue 07/04 User Documentation Micromaster 420 Documentation Getting Started GuideOperating Instructions Parameter List Operating Instructions Valid for Release Micromaster Online Service & Support User DocumentationInformation is also available from Regional Contacts Central Technical Support Use for intended purpose only Qualified personnel Safety Instructions General Transport & Storage Commissioning Dismantling & Disposal OperationRepair Safety Instructions Issue 07/04 Table of Contents 151 152153 154 List of Illustrations OFF1 List of Tables Table of Contents Issue 07/04 Overview This Chapter contains Micromaster Performance Characteristics FeaturesMain Characteristics Protection characteristics Options Installation Installation Issue 07/04 Installation after a Period of Storage TemperatureGeneral Ambient operating conditions Installation and cooling HumidityAltitude Shock and Vibration Mechanical installation Removing the Inverter from the rail Mounting on standard rail, Frame Size aFitting the Inverter to a 35 mm standard rail EN Electrical installation Inverter must always be grounded General Operation with ungrounded IT suppliesOperation with Residual Current Device Operation with long cables Power and motor connections Access to the power and motor terminals Single Phase Three Phase Control terminals Terminal Designation Function Avoiding Electro-Magnetic Interference EMI Action to Take Screening without a Gland Plate Screening MethodsGland Plate Installation Issue 07/04 Functions This Section includes the following Functions Issue 07/04 Issue 07/04 Functions Setting / monitoring parameters and parameter attributes Setting parametersParameters Notation Monitoring parameters Attribute Description Group Inverter P03053 Rated motor current P0003 = P0003 =P0004 = Interconnecting signals Bico technology Significance / command source Significance Main setpoint source Supplementary setpoint source Selection of command/frequency setpoint P0719 Command source BI Binector Input, signal receiver P parameters BO Binector Output, signal source r parametersAbbreviation and symbol Name Function Bico technology CI Connector Input, signal sink P parameters CO Connector Output, signal source r parameters P1070 = P0840 =P2051 = P0731 = Parameter Designation Value 100 % Units Reference quantitiesInterface 100 % Example Operator panels for Micromaster Description of the BOP Basic Operator Panel Description of the AOP Advanced Operator Panel Keys and their functions on the operator panel BOP / AOP Operator Function Effects Panel/key Step Result on the display Changing parameters using the operator panelChanging P0004 parameter filter function Block diagram External 24 Factory setting Parameter Function 13 Recommended wiring for the factory setting 14 Procedure when commissioning Commissioning Check list 1 50/60 Hz setting 15 DIP switch to change-over between 50/60 Hz Factory setting User access level Quick commissioningParameterizing the drive with BOP or AOP Commissioning parameter Europe kW, frequency default 50 Hz Rated motor powerEurope/ North America Rated motor voltage Selection of command source Control modeEnd of quick commissioning/ drive setting Selection of frequency setpoint 17 Example of a typical motor rating plate IEC Motor Nema Motor Hz characteristic 19 Star / delta circuit configurations 87 Hz Calculating the motor / control data Motor data identification stator resistance Ambient motor temperature entered in C Power-up the motorDisabled Motor data identification routine Serial Interface USS Commissioning the applicationAdapting the drive inverter to the application 5.2 Selection of command source Digital input DIN Selection of frequency setpoint Digital output Dout5.5 Analog input ADC 5.7 Analog output DAC Motor potentiometer MOP Fixed frequency FF 5.10 JOG Ramp-function generator HLG Reference/limit frequencies Motor control Acceleration boost entered in % Starting boost entered in %Programmable V/f freq .0 Hz coord Slip compensation entered in % Inverter/motor protection Holding brake Inverter-specific Functions Flying startAutomatic restart DC braking Compound brakingVdc controller PID controller Max. value for PID feedback Sets lower limit for the PID controller output in %Example Parameter Parameter text Example Series commissioning MM4 Issue 07/04 Functions Factory reset Parameter reset to the factory settingReset to the factory setting Inputs / outputs Digital inputs DIN Parameter value Significance P0701 P0703 digital inputs 1-3 or P0707 P0703 analog inputExample Bico parameterization Digital output Dout 11 Parameter P0731 frequently used functions / states Analog input ADC ADC channel Wire breakage monitoring 26 Wire breakage monitoring 27 Signal output through the DAC channel Analog output DAC Communications Starter USS BOP link interface BOP on BOP link USS on BOP link COM link interface CB on COM link USS on COM link USS at the COM link RS485 USS bus configuration via COM link RS485 30 RS485 Terminator Fixed frequencies FF Direct selection Direct selection + on command Binary-coded selection + on command R0722.1 Motorized potentiometer MOP Selecting via serial interfaces AOP at the BOP link Selecting via BOP or AOPParameters / keys 10 JOG 35 JOG counter-clockwise and JOG clockwise 105 PID controller technological controller 36 Structure of the technological controller PID controller Parameterizations PID motorized potentiometer PID-MOP PID motorized potentiometer Motorized potentiometer PID fixed setpoint PID-FF Setpoint channel Summation and modification of the frequency setpoint AFM 111 Ramp-function generator RFG With rounding P1132 P1133 P1134 = 19 Bico parameters for ramp-function generator Parameter Description 12.3 OFF/braking functions OFF1 OFF2 Parameter setting Command source Manual / automatic operation Value Command source Setpoint source Motor holding brake MHB On / OFF1/OFF3 On / OFF2 49 Motor holding brake after OFF2 121 Electronic brakes 14.1 DC braking Sequence ➀ 51 DC braking after OFF1 / OFF3 Sequence ➁ 52 DC braking after external selection Compound braking 53 Compound braking 126 Automatic restart Line undervoltage brownoutLine failure blackout Blackout Brownout 128 Flying restart Flying restart active Search direction 130 Closed-loop Vdc control Vdcmax controllerDC link undervoltage Cause 132 Monitoring functions / messages General monitoring functions / messages Function chart Functions / states Thermal motor model FeaturesThermal motor protection and overload responses 136 19.2 PTC temperature sensor Temperature Classes 58 Connecting a temperature sensor to Micromaster General overload monitoring Power module protectionFault and shutdown I2t monitoring Heatsink temperatureThermal monitoring functions and overload responses Reducing the output frequency P0290 = 0,2 Reducing the pulse frequency P0290 = 2Disadvantage No reduction P0290 = Open-loop/closed-loop control technique 21.1 Control 27 V/f characteristic parameter P1300 Use / property Voltage boost Parameter Voltage boost Explanation 146 21.1.2 V/f open-loop control with flux current control FCC Slip compensation 62 Slip compensation 21.1.4 V/f resonance damping 63 Effect of V/f resonance damping Current limiting Imax controller Imax controller setpoint Troubleshooting Troubleshooting with the SDP Troubleshooting Issue 07/04 Troubleshooting with the BOP Alarm messages Fault messages and alarm messagesFault messages Suppressing fault / alarm messages 156 Micromaster 420 specifications Micromaster 420 specifications Issue 07/04 Feature Specification KHz 10 kHz 12 kHz 14 kHz 16 kHz Lbs 2AB11 2AB12 2AB13 2AB15 2AB17 2AB21 2AB22 2AB231BA1 5BA1 Input voltage range AC 200 V 240 V, ± 10 % Unfiltered 2UC11 2UC12 2UC13 2UC15 2UC17 2UC21 2UC22 2UC23KVA Awg 2UC25 2UC12 2UC131BA1 5BA1 2BA1 2BA1 0BA1 2AD23 2AD242AD31 2UD25 2UD27 2UD31 Input voltage range AC 380 V 480 V, ± 10 % Unfiltered2UD13 2UD15 2UD17 2UD21 2UD22 2UD23 2UD24 Device-dependent options OptionsDevice-independent options Options Issue 07/04 Electro-magnetic compatibility EMC Electro-magnetic compatibility EMC Self-certificationTechnical construction file EC type examination certificate EMC Directive Compliance with Imminent Harmonics Regulations Classification of EMC performance Class 1 General IndustrialClass 2 Filtered Industrial EMC Phenomenon Standard Level 171 Class Model RemarksClass 1 General Industrial Appendices Changing the OperatorPanel Removing Covers Removing Covers Frame Size a 6SE6400-5AA00-0BP0 Removing ‘Y’ Cap Removing ‘Y’ Cap Frame Size a Issue 07/04 Removing ‘Y’ Cap Removing fan Removing fan, Frame Size a Removing fan, Frame Sizes B and C Applicable Standards List of Abbreviations COM List of Abbreviations Issue 07/04 PPO Index Issue 07/04 Index Ungrounded IT supplies Suggestions and/or Corrections Suggestions Corrections 188 View of Unit Frame Size a Frame Size B & C Siemens Aktiengesellschaft