Single Phase, Three Phase | Siemens 420 manual

2 Installation

Issue 07/04

	L3		Single Phase
	L2		Single Phase
	L1
	N	Contactor	Optional	Optional	MICROMASTER 1)		Motor
		Contactor	line choke	Filter	MICROMASTER 1)		Motor
	Fuse
					L/L1	U
						V
					N/L2	W
					PE
			PE	PE
	L3		Three Phase
	L3
	L2		Optional	Optional
	L1	Contactor	Optional	Optional	MICROMASTER 1)		Motor
	L1		line choke	Filter
			line choke	Filter
	Fuse
					L3	U
					L2	V
					L1	W
					PE
			PE	PE
	1) with and without filter

Fig. 2-6 Motor and Power Connections

MICROMASTER 420	Operating Instructions
30	6SE6400-5AA00-0BP0

Image 30

Siemens 420 manual Single Phase, Three Phase

Contents

Operating Instructions Issue 07/04 User Documentation Operating Instructions Micromaster 420 DocumentationGetting Started Guide Parameter List Operating Instructions Valid for Release Micromaster Information is also available from Regional Contacts Online Service & SupportUser Documentation Central Technical Support Use for intended purpose only Qualified personnel Safety Instructions General Transport & Storage Commissioning Operation RepairDismantling & Disposal Safety Instructions Issue 07/04 Table of Contents 153 151152 154 List of Illustrations OFF1 List of Tables Table of Contents Issue 07/04 Overview This Chapter contains Micromaster Features Main CharacteristicsPerformance Characteristics Protection characteristics Options Installation Installation Issue 07/04 General Installation after a Period of StorageTemperature Ambient operating conditions Altitude Installation and coolingHumidity Shock and Vibration Mechanical installation Mounting on standard rail, Frame Size a Fitting the Inverter to a 35 mm standard rail ENRemoving the Inverter from the rail Electrical installation Inverter must always be grounded Operation with Residual Current Device GeneralOperation with ungrounded IT supplies Operation with long cables Power and motor connections Access to the power and motor terminals Single Phase Three Phase Control terminals Terminal Designation Function Avoiding Electro-Magnetic Interference EMI Action to Take Screening Methods Gland PlateScreening without a Gland Plate Installation Issue 07/04 Functions This Section includes the following Functions Issue 07/04 Issue 07/04 Functions Parameters Setting / monitoring parameters and parameter attributesSetting parameters Notation Monitoring parameters Attribute Description Group Inverter P03053 Rated motor current P0003 = P0004 =P0003 = Interconnecting signals Bico technology Significance / command source Significance Main setpoint source Supplementary setpoint source Selection of command/frequency setpoint P0719 Command source Abbreviation and symbol Name Function BI Binector Input, signal receiver P parametersBO Binector Output, signal source r parameters Bico technology CI Connector Input, signal sink P parameters CO Connector Output, signal source r parameters P2051 = P1070 =P0840 = P0731 = Reference quantities Interface 100 %Parameter Designation Value 100 % Units Example Operator panels for Micromaster Description of the BOP Basic Operator Panel Description of the AOP Advanced Operator Panel Keys and their functions on the operator panel BOP / AOP Operator Function Effects Panel/key Changing parameters using the operator panel Changing P0004 parameter filter functionStep Result on the display Block diagram External 24 Factory setting Parameter Function 13 Recommended wiring for the factory setting 14 Procedure when commissioning Commissioning Check list 1 50/60 Hz setting 15 DIP switch to change-over between 50/60 Hz Parameterizing the drive with BOP or AOP Factory setting User access levelQuick commissioning Commissioning parameter Europe/ North America Europe kW, frequency default 50 HzRated motor power Rated motor voltage End of quick commissioning/ drive setting Selection of command sourceControl mode Selection of frequency setpoint 17 Example of a typical motor rating plate IEC Motor Nema Motor Hz characteristic 19 Star / delta circuit configurations 87 Hz Calculating the motor / control data Motor data identification stator resistance Disabled Ambient motor temperature entered in CPower-up the motor Motor data identification routine Commissioning the application Adapting the drive inverter to the applicationSerial Interface USS 5.2 Selection of command source Digital input DIN Digital output Dout 5.5Selection of frequency setpoint Analog input ADC 5.7 Analog output DAC Motor potentiometer MOP Fixed frequency FF 5.10 JOG Ramp-function generator HLG Reference/limit frequencies Motor control Programmable V/f freq .0 Hz coord Acceleration boost entered in %Starting boost entered in % Slip compensation entered in % Inverter/motor protection Inverter-specific Functions Flying start Automatic restartHolding brake Vdc controller DC brakingCompound braking PID controller Example Max. value for PID feedbackSets lower limit for the PID controller output in % Parameter Parameter text Example Series commissioning MM4 Issue 07/04 Functions Parameter reset to the factory setting Reset to the factory settingFactory reset Inputs / outputs Digital inputs DIN P0701 P0703 digital inputs 1-3 or P0707 P0703 analog input ExampleParameter value Significance Bico parameterization Digital output Dout 11 Parameter P0731 frequently used functions / states Analog input ADC ADC channel Wire breakage monitoring 26 Wire breakage monitoring 27 Signal output through the DAC channel Analog output DAC Communications Starter USS BOP link interface BOP on BOP link USS on BOP link COM link interface CB on COM link USS on COM link USS at the COM link RS485 USS bus configuration via COM link RS485 30 RS485 Terminator Fixed frequencies FF Direct selection Direct selection + on command Binary-coded selection + on command R0722.1 Motorized potentiometer MOP Selecting via serial interfaces Selecting via BOP or AOP Parameters / keysAOP at the BOP link 10 JOG 35 JOG counter-clockwise and JOG clockwise 105 PID controller technological controller 36 Structure of the technological controller PID controller Parameterizations PID motorized potentiometer PID-MOP PID motorized potentiometer Motorized potentiometer PID fixed setpoint PID-FF Setpoint channel Summation and modification of the frequency setpoint AFM 111 Ramp-function generator RFG With rounding P1132 P1133 P1134 = 19 Bico parameters for ramp-function generator Parameter Description 12.3 OFF/braking functions OFF1 OFF2 Parameter setting Command source Manual / automatic operation Value Command source Setpoint source Motor holding brake MHB On / OFF1/OFF3 On / OFF2 49 Motor holding brake after OFF2 121 Electronic brakes 14.1 DC braking Sequence ➀ 51 DC braking after OFF1 / OFF3 Sequence ➁ 52 DC braking after external selection Compound braking 53 Compound braking 126 Line failure blackout Automatic restartLine undervoltage brownout Blackout Brownout 128 Flying restart Flying restart active Search direction 130 DC link undervoltage Closed-loop Vdc controlVdcmax controller Cause 132 Monitoring functions / messages General monitoring functions / messages Function chart Functions / states Features Thermal motor protection and overload responsesThermal motor model 136 19.2 PTC temperature sensor Temperature Classes 58 Connecting a temperature sensor to Micromaster Power module protection Fault and shutdownGeneral overload monitoring Heatsink temperature Thermal monitoring functions and overload responsesI2t monitoring Reducing the pulse frequency P0290 = 2 DisadvantageReducing the output frequency P0290 = 0,2 No reduction P0290 = Open-loop/closed-loop control technique 21.1 Control 27 V/f characteristic parameter P1300 Use / property Voltage boost Parameter Voltage boost Explanation 146 21.1.2 V/f open-loop control with flux current control FCC Slip compensation 62 Slip compensation 21.1.4 V/f resonance damping 63 Effect of V/f resonance damping Current limiting Imax controller Imax controller setpoint Troubleshooting Troubleshooting with the SDP Troubleshooting Issue 07/04 Troubleshooting with the BOP Fault messages and alarm messages Fault messagesAlarm messages Suppressing fault / alarm messages 156 Micromaster 420 specifications Micromaster 420 specifications Issue 07/04 Feature Specification KHz 10 kHz 12 kHz 14 kHz 16 kHz 2AB11 2AB12 2AB13 2AB15 2AB17 2AB21 2AB22 2AB23 1BA1 5BA1Lbs KVA Input voltage range AC 200 V 240 V, ± 10 % Unfiltered2UC11 2UC12 2UC13 2UC15 2UC17 2UC21 2UC22 2UC23 Awg 2UC12 2UC13 1BA1 5BA1 2BA12UC25 2AD23 2AD24 2AD312BA1 0BA1 Input voltage range AC 380 V 480 V, ± 10 % Unfiltered 2UD13 2UD15 2UD17 2UD21 2UD22 2UD23 2UD242UD25 2UD27 2UD31 Options Device-independent optionsDevice-dependent options Options Issue 07/04 Electro-magnetic compatibility EMC Technical construction file Electro-magnetic compatibility EMCSelf-certification EC type examination certificate EMC Directive Compliance with Imminent Harmonics Regulations Class 2 Filtered Industrial Classification of EMC performanceClass 1 General Industrial EMC Phenomenon Standard Level 171 Model Remarks Class 1 General IndustrialClass Appendices Changing the OperatorPanel Removing Covers Removing Covers Frame Size a 6SE6400-5AA00-0BP0 Removing ‘Y’ Cap Removing ‘Y’ Cap Frame Size a Issue 07/04 Removing ‘Y’ Cap Removing fan Removing fan, Frame Size a Removing fan, Frame Sizes B and C Applicable Standards List of Abbreviations COM List of Abbreviations Issue 07/04 PPO Index Issue 07/04 Index Ungrounded IT supplies Suggestions and/or Corrections Suggestions Corrections 188 View of Unit Frame Size a Frame Size B & C Siemens Aktiengesellschaft