Significance | Siemens 420 manual

Issue 07/04

3 Functions

Table 3-3	Parameter P1000

Parameter values			Significance
Parameter values		Main setpoint source		Supplementary setpoint source
		Main setpoint source		Supplementary setpoint source
0		No main setpoint		-
1		MOP setpoint (motorized		-
1		potentiometer)		-
		potentiometer)
2		Analog setpoint		-

3		Fixed frequency		-
4		USS on BOP link		-

5		USS on COM link		-

6		CB on COM link		-

10		No main setpoint		MOP setpoint
11		MOP setpoint		MOP setpoint

12		Analog setpoint		MOP setpoint

..		..		..

..		..		..
66		CB on COM link		CB on COM link

NOTE

Communications between the AOP and MICROMASTER are established using the USS protocol. The AOP can be connected to both the BOP link (RS 232) as well as at the COM link interface (RS 485) of the drive inverter. If the AOP is to be used as command source or setpoint source then for parameter P0700 or P1000, either "USS on BOP link" or "USS on COM link" should be selected.

The complete list of all of the setting possibilities can be taken from the parameter list (refer to parameter list P1000).

Parameters P0700 and P1000 have the following default settings:

a)P0700 = 2 (terminal strip)

b)P1000 = 2 (analog setpoint)

In this case, the selection of the command source is made independently of the selection of the frequency setpoint source. This means that the source to enter the setpoint does not have to match the source to enter the power-on/power-off command (command source). This means, for example, that the setpoint (P1000 =

4)can be connected via an external device which is connected to the BOP link interface via USS and the control ON/OFF command, etc. is entered via digital inputs (terminals, P0700 = 2).

CAUTION

When modifying P0700 or P1000, then the drive inverter also changes the subordinate BICO parameters (refer to the parameter list for P0700 or P1000 and the appropriate tables)

No priority has assigned between the direct BICO parameterization and P0700/P1000. The last modification is valid.

MICROMASTER 420	Operating Instructions
6SE6400-5AA00-0BP0	45

Image 45

Siemens 420 manual Significance, Main setpoint source Supplementary setpoint source

Contents

User Documentation Operating Instructions Issue 07/04 Getting Started Guide Micromaster 420 DocumentationOperating Instructions Parameter List Valid for Release Operating Instructions Micromaster User Documentation Online Service & SupportInformation is also available from Regional Contacts Central Technical Support Qualified personnel Use for intended purpose only General Safety Instructions Commissioning Transport & Storage Operation RepairDismantling & Disposal Safety Instructions Issue 07/04 Table of Contents 152 151153 154 List of Illustrations OFF1 List of Tables Table of Contents Issue 07/04 This Chapter contains Overview Micromaster Features Main CharacteristicsPerformance Characteristics Options Protection characteristics Installation Installation Issue 07/04 Temperature Installation after a Period of StorageGeneral Ambient operating conditions Humidity Installation and coolingAltitude Shock and Vibration Mechanical installation Mounting on standard rail, Frame Size a Fitting the Inverter to a 35 mm standard rail ENRemoving the Inverter from the rail Inverter must always be grounded Electrical installation Operation with ungrounded IT supplies GeneralOperation with Residual Current Device Operation with long cables Access to the power and motor terminals Power and motor connections Three Phase Single Phase Terminal Designation Function Control terminals Action to Take Avoiding Electro-Magnetic Interference EMI Screening Methods Gland PlateScreening without a Gland Plate Installation Issue 07/04 This Section includes the following Functions Functions Issue 07/04 Issue 07/04 Functions Setting parameters Setting / monitoring parameters and parameter attributesParameters Notation Monitoring parameters Attribute Description Group Inverter Rated motor current P03053 P0003 = P0004 =P0003 = Significance / command source Interconnecting signals Bico technology Main setpoint source Supplementary setpoint source Significance Command source Selection of command/frequency setpoint P0719 BO Binector Output, signal source r parameters BI Binector Input, signal receiver P parametersAbbreviation and symbol Name Function Bico technology CO Connector Output, signal source r parameters CI Connector Input, signal sink P parameters P0840 = P1070 =P2051 = P0731 = Reference quantities Interface 100 %Parameter Designation Value 100 % Units Example Description of the BOP Basic Operator Panel Operator panels for Micromaster Description of the AOP Advanced Operator Panel Operator Function Effects Panel/key Keys and their functions on the operator panel BOP / AOP Changing parameters using the operator panel Changing P0004 parameter filter functionStep Result on the display External 24 Block diagram Parameter Function Factory setting 13 Recommended wiring for the factory setting Commissioning 14 Procedure when commissioning Check list 15 DIP switch to change-over between 50/60 Hz 1 50/60 Hz setting Quick commissioning Factory setting User access levelParameterizing the drive with BOP or AOP Commissioning parameter Rated motor power Europe kW, frequency default 50 HzEurope/ North America Rated motor voltage Control mode Selection of command sourceEnd of quick commissioning/ drive setting Selection of frequency setpoint 17 Example of a typical motor rating plate Nema Motor IEC Motor 19 Star / delta circuit configurations Hz characteristic 87 Hz Calculating the motor / control data Motor data identification stator resistance Power-up the motor Ambient motor temperature entered in CDisabled Motor data identification routine Commissioning the application Adapting the drive inverter to the applicationSerial Interface USS Digital input DIN 5.2 Selection of command source Digital output Dout 5.5Selection of frequency setpoint 5.7 Analog output DAC Analog input ADC Fixed frequency FF Motor potentiometer MOP Ramp-function generator HLG 5.10 JOG Motor control Reference/limit frequencies Starting boost entered in % Acceleration boost entered in %Programmable V/f freq .0 Hz coord Slip compensation entered in % Inverter/motor protection Inverter-specific Functions Flying start Automatic restartHolding brake Compound braking DC brakingVdc controller PID controller Sets lower limit for the PID controller output in % Max. value for PID feedbackExample Parameter Parameter text Example MM4 Series commissioning Issue 07/04 Functions Parameter reset to the factory setting Reset to the factory settingFactory reset Digital inputs DIN Inputs / outputs P0701 P0703 digital inputs 1-3 or P0707 P0703 analog input ExampleParameter value Significance Bico parameterization Digital output Dout 11 Parameter P0731 frequently used functions / states ADC channel Analog input ADC 26 Wire breakage monitoring Wire breakage monitoring Analog output DAC 27 Signal output through the DAC channel Starter USS Communications COM link interface CB on COM link USS on COM link BOP link interface BOP on BOP link USS on BOP link USS at the COM link RS485 30 RS485 Terminator USS bus configuration via COM link RS485 Direct selection Fixed frequencies FF Direct selection + on command R0722.1 Binary-coded selection + on command Selecting via serial interfaces Motorized potentiometer MOP Selecting via BOP or AOP Parameters / keysAOP at the BOP link 35 JOG counter-clockwise and JOG clockwise 10 JOG 105 36 Structure of the technological controller PID controller PID controller technological controller Parameterizations PID motorized potentiometer Motorized potentiometer PID motorized potentiometer PID-MOP PID fixed setpoint PID-FF Summation and modification of the frequency setpoint AFM Setpoint channel 111 With rounding Ramp-function generator RFG P1134 = P1132 P1133 Parameter Description 19 Bico parameters for ramp-function generator OFF1 12.3 OFF/braking functions OFF2 Manual / automatic operation Parameter setting Command source Value Command source Setpoint source On / OFF1/OFF3 Motor holding brake MHB 49 Motor holding brake after OFF2 On / OFF2 121 14.1 DC braking Electronic brakes 51 DC braking after OFF1 / OFF3 Sequence ➀ 52 DC braking after external selection Sequence ➁ 53 Compound braking Compound braking 126 Line undervoltage brownout Automatic restartLine failure blackout Blackout Brownout 128 Flying restart active Search direction Flying restart 130 Vdcmax controller Closed-loop Vdc controlDC link undervoltage Cause 132 General monitoring functions / messages Monitoring functions / messages Functions / states Function chart Features Thermal motor protection and overload responsesThermal motor model 136 Temperature Classes 19.2 PTC temperature sensor 58 Connecting a temperature sensor to Micromaster Power module protection Fault and shutdownGeneral overload monitoring Heatsink temperature Thermal monitoring functions and overload responsesI2t monitoring Reducing the pulse frequency P0290 = 2 DisadvantageReducing the output frequency P0290 = 0,2 No reduction P0290 = 21.1 Control Open-loop/closed-loop control technique Use / property 27 V/f characteristic parameter P1300 Parameter Voltage boost Explanation Voltage boost 146 21.1.2 V/f open-loop control with flux current control FCC 62 Slip compensation Slip compensation 63 Effect of V/f resonance damping 21.1.4 V/f resonance damping Imax controller setpoint Current limiting Imax controller Troubleshooting Troubleshooting Issue 07/04 Troubleshooting with the SDP Troubleshooting with the BOP Fault messages and alarm messages Fault messagesAlarm messages Suppressing fault / alarm messages 156 Micromaster 420 specifications Feature Specification Micromaster 420 specifications Issue 07/04 KHz 10 kHz 12 kHz 14 kHz 16 kHz 2AB11 2AB12 2AB13 2AB15 2AB17 2AB21 2AB22 2AB23 1BA1 5BA1Lbs 2UC11 2UC12 2UC13 2UC15 2UC17 2UC21 2UC22 2UC23 Input voltage range AC 200 V 240 V, ± 10 % UnfilteredKVA Awg 2UC12 2UC13 1BA1 5BA1 2BA12UC25 2AD23 2AD24 2AD312BA1 0BA1 Input voltage range AC 380 V 480 V, ± 10 % Unfiltered 2UD13 2UD15 2UD17 2UD21 2UD22 2UD23 2UD242UD25 2UD27 2UD31 Options Device-independent optionsDevice-dependent options Options Issue 07/04 Electro-magnetic compatibility EMC Self-certification Electro-magnetic compatibility EMCTechnical construction file EC type examination certificate EMC Directive Compliance with Imminent Harmonics Regulations Class 1 General Industrial Classification of EMC performanceClass 2 Filtered Industrial EMC Phenomenon Standard Level 171 Model Remarks Class 1 General IndustrialClass Appendices Changing the OperatorPanel Removing Covers Frame Size a Removing Covers 6SE6400-5AA00-0BP0 Removing ‘Y’ Cap Frame Size a Removing ‘Y’ Cap Issue 07/04 Removing ‘Y’ Cap Removing fan, Frame Size a Removing fan Removing fan, Frame Sizes B and C Applicable Standards COM List of Abbreviations List of Abbreviations Issue 07/04 PPO Index Issue 07/04 Index Ungrounded IT supplies Suggestions Corrections Suggestions and/or Corrections 188 Frame Size B & C View of Unit Frame Size a Siemens Aktiengesellschaft