First Operation, OTS9100 Installation | Tektronix 071-0855-05

Getting Started

First Operation

OTS9100 Installation

Before using the system, verify that it is properly set up and powered on, as follows:

1.Remove the unit from its shipping carton and place it on an anti-static surface.

2.Verify that the operating environment is within the limits detailed under the Environmental Requirement section in this manual.

3.Allow approximately 2 inches (5 cm) clearance for cooling at the front and rear of the unit. The fans draw air into the system from the front and exhaust the air through the rear of the OTS9000 chassis system or through the sides of the OTS9010 and OTS9040 chassis systems.

4.If the module cards are not already installed, perform the following steps:

CAUTION! When installing and removing cards from the chassis, power must not be present. Ensure that all power switches are in the OFF position and power cords are not installed before removing or installing cards. The chassis does NOT support hot-swap installations.

A. Remove the cards from the packaging, if necessary.

CAUTION! All OTS cards are static sensitive. When handling cards, ensure that personnel are properly grounded and OTS cards are always placed on anti-static surfaces. If proper precautions are not taken, damage will occur.

B.For those locations in which cards are being installed, remove the blanking panels and air diverters.

C.Verify the required configuration of cards before proceeding. Carefully install each card into a slot in the chassis. Make sure that the card is lined up and fits cleanly with the connectors into the backplane of the chassis.

CAUTION! Beware of bending the pins of the connectors when installing and removing cards from the chassis. Backplane connectors with bent pins will cause damage to both the card and the chassis.

To install the card, slowly slide the card into the desired slot. Make sure the card is lined up with the connectors and push down on the top release and up on the bottom release until the card snaps into place.

OTS9100 User Manual

1-7

Image 21

Tektronix 071-0855-05 user manual First Operation, OTS9100 Installation

Contents

OTS USA Warranty Page Table of Contents Analysis SONET/T1M1 Analysis SDH/G.826 Reference Iii SOURceDATAPAYLoadBACKgroundPATTern Appendices How to Avoid Fire or Personal Injury General Safety Summary Keep Product Surfaces Clean and Dry General Safety Summary Symbols on the Product Safety Terms and SymbolsTerms in this Manual Terms on the Product General Safety Summary Viii How This Manual is Organized Preface Conventions Product Description Getting Started OTS9100 Features and Capabilities Getting Started Standard with each shipment AccessoriesOTS91L4 Standard OTS91L5 Standard OTS91L8 Standard OTS91L7 StandardOTS91R2 Standard OTS91T3 Standard Adapters, SMA International Power Plug Options Chassis Only First Operation OTS9100 Installation Removing Cards Multiple Modules Slot Positioning of OTS Cards OTS9000 with card slot assignment Module Card Interconnection Proper location Interconnection cables Power On and Software Initialization Transmitter Setup Receiver SetupModule Quick Check Getting Started Emergency Startup Disk Shutdown and Power Off OTS9100 Front Panel Front Panel Indicators and Connectors 10Gb/s Transceiver Optics Module OKOptical OUT Rx Data OUT OpticalTx Data Appropriate circuit. -3 1550 nm Transceiver Front Panel Laser Lockout, Remote Interlock Defect indicator will turn off when a new test is started Receive AnalysisModule OK Rx Event OUT Rx DataRx Clock OUT Transmit Generation Tx Event OUTTransmit Front Panel MHz Trig OUT Tx Data OUTGHz Clock MHz External Clock Clock TriggerGHz Trig OUT Rx Clock GHz Clock Out Software Interface Operating Basics Elements of the User Interface Menu Bar Task BarSystem View Multiple Mode Single ModeMultiple Window Mode View Window Laser Control Bar Tool Bar Test Control Bar ErrorMain Status Bar Client Lockout Test Laser OffFrame Grabbers LED Window Slot Signal LED Panel Module Signal Summary LED PanelUser Selected Signal LED Window Clear History LED Module Display Module LED Panel SEF OOF Description of Status Window Virtual LED Indicators LED Display Selection Select Signal User Selected Signal Slot Signal Navigation Window Summary Icons Scroll Buttons Setup Property Menus 10 Transmitter Setup Signal menu Signal Standard Signal Source Bert ModeTiming Source Trigger Output SPE/VC3 Stuff Column Control Packet Over Sonet POS Background Channels 11 Transmitter Transport Overhead menu Transmitter Transport Overhead 12 Edit Overhead dialog box Edit Overhead 13 Through Mode Overwrite menu Through Mode 14 Transmitter J0 Trace dialog box J0 Multi-Byte Trace 16 Transmitter Path Overhead Property Menu Transmitter Path Overhead Edit Path Overhead Path Through Mode 19 Transmitter J1 Trace dialog box J1 Multi-Byte Trace 21 Transmitter Error Insertion menu Transmitter Error Insertion Anomaly Insertion Anomaly Insertion and Through Mode Defect Insertion 23 Defect Insertion of the Error Insertion menu 24 Transmitter K1, K2 Decode menu Transmitter K1, K2 Decode 25 Edit K1, K2 Bytes dialog box Operating Basics User Interface Transmitter IP Payload IP Setup IP Header Error Selection Transmitter IP Error Insertion Current Error Insertion 26 Receiver Setup Signal menu Receiver Signal Test Pattern Signal Structure 27 Receiver Threshold Offset dialog box Receiver Threshold Offset Receiver Trace Mismatch 28 Receiver Setup Trace Mismatch menu 29 J0 Trace Editor dialog box Edit C2 Byte 31 Edit C2 dialog box Hpplm and HP Unequipped Detection Receiver IP Setup 32 Setup Summary menu Setup Summary Receiver Transport Overhead Signal Monitor Menus S1 Synchronization Status RS Trace Section Trace J0 Receiver Path Overhead 35 Signal Monitor Path Overhead C2 Status Path Trace J1 Receiver K1,K2 Decode 36 Signal Monitor K1,K2 Decode Receiver Payload 37 Signal Monitor Payload Test Control Menu 39 Test Control Parameters dialog box 40 Test Control Summary menu Test Control Summary Receiver Real-Time Measurements Menu 42 Real-Time menu Path display 44 Cumulative Measurements Display Section and Line Receiver Cumulative 45 Cumulative Measurements Display Path 46 Example of Results History Data Section/Line Receiver History 47 Example of Results History Data -Path Operating Basics User Interface Receiver IP Measurements display Receiver IP Measurements Transmitter IP Measurements Analysis SONET/T1M1 Analysis Menu 49 Analysis menu SONET/T1M1 Path 50 Analysis menu SDH/G.826 RS/MS Analysis SDH/G.826 51 Analysis menu SDH/G.826 Path 52 APS Measurements menu APS Measurements Menu 53 Set APS Test Parameters dialog box 54 Copy APS Measurement Data dialog box Remote Access Setups Select Server 59 View Options dialog box Display Notation Server System Display Configuration System View 63 View Scpi Output dialog box Scpi Output Results File Management Results Files 64 Results File Management dialog box Operation ResultsViewerOpening files on the local computer On the Local computer 65 Cumulative Results screen of the ResultsViewer Connecting to an OTS System Viewing results files Selecting and arranging windows Configuring ResultsViewerPrinting results data Exporting test data to other programs Sample output of data from a test results file A202 A604 Summary report Test file info Record type codes Sonet GR-253 Line Analysis History data 66 Configure Data Report dialog box Configuring the exported data Starting the Event Printer program LoggingSelect Events Copy to File Copy to ClipboardCopy to Printer Clear Configuring a printer in Windows Muting Event Printer behavior with continuous eventsMinimizing the Event Printer window 102 Commands Overview Ieee 488.2 System CommandsRemote Control Setup and Format Commands Remote Control Port Settings Remote Control LockoutSystem Configuration Queries System Signal Standard OTS9100 module Save and Restore System SettingsReceiver Commands OTS9100 module System File Management Receiver Signal Measurement Commands OTS9100 module Receiver Signal Analysis Commands OTS9100 moduleReceiver Test Control OTS9100 module Transmitter Commands OTS9100 module Command and Query Structure Ieee 488.2 Common CommandsSyntax Description Hex Block Format Block Format Command Format Scpi Commands and QueriesQuery format Example Sourcedatapayloadpattern Enum Parameter types and formats #216ABCDEFGHIJKLMNOP Optional and alternative parameters Controlling Responses to Queries Abbreviating Commands, Queries, and ParametersMinimum information needed Accepted short form Example of chaining commands and queries Chaining Commands and Queries Slot Specifiers General Rules ESE Command Description OPC SENSeANALysisG826AMSFARALL SENSeANALysisG826AMSFAR SENSeANALysisG826AMSNEAR SENSeANALysisG826AMSNEARALLSENSeANALysisG826APATHFAR SENSeANALysisG826APATHFARALL SENSeANALysisG826APATHNEARSENSeANALysisG826APATHNEARALL SENSeANALysisG826ARS SENSeANALysisG826ARSALLSENSeANALysisGR253ALINEFAR SENSeANALysisGR253ALINEFARALL SENSeANALysisGR253ALINENEARSENSeANALysisGR253ALINENEARALL SENSeANALysisGR253APATHFARALL SENSeANALysisGR253APATHFAR SENSeANALysisGR253APATHNEARALL SENSeANALysisGR253APATHNEAR SENSeANALysisGR253ASECTion SENSeANALysisGR253ASECTionALLSENSeANALysisPATHHPPLM SENSeANALysisPATHHPUNEQ SENSeANALysisPATHHPPLMGENEricSENSeANALysisPATHLABElEXPEcted SENSeANALysisPATHTRACeEXPEcted SENSeANALysisPATHTRACeEXPEctedTYPE SENSeANALysisPATHTRACeEXPEctedVALUeSENSeANALysisPATHTRACeEXPEctedVALUeSTRIng SENSeANALysisPATHTRACeTIM SENSeANALysisSECTionTRACeEXPEctedSENSeANALysisSECTionTRACeEXPEctedTYPE SENSeANALysisSECTionTRACeEXPEctedVALUeSTRIng SENSeANALysisSECTionTRACeEXPEctedVALUeSENSeANALysisSECTionTRACeTIM SENSeDATAAUTOscanSTRUcture SENSeDATAIPPAYLoadPATTern SENSeDATACHANnelSENSeDATAIPPAYLoadPATTernUDATA SENSeDATAIPSTReamINDEX SENSeDATAPATHTRACeVALUe SENSeDATAPATHTRACeTYPESENSeDATAPATHTRACeVALUeSTRIng SENSeDATAPAYLoadPATTern SENSeDATAPOHALL SENSeDATAPAYLoadPATTernUDATASENSeDATAPOHBYTE SENSeDATAPOHBYTEC2A SENSeDATASECTionTRACe SENSeDATARATESENSeDATASECTionTRACeTYPE SENSeDATASECTionTRACeVALUe SENSeDATASTRUcture SENSeDATASPESTUFfingSENSeDATATOHSTM1AALL SENSeDATATOHSTS1AALL SENSeINPUtTHREshold SENSeINPutTHResholdLOSSENSeMEASureAPSTimeCONDition SENSeMEASureAPSTimeDETEcted SENSeMEASureAPSTimeRUNSENSeMEASureAPSTimeMAXTime SENSeMEASureAPSTimeSTATus SENSeMEASureAPSTimeVALUe SENSeMEASureAPSTimeTHREsholdSENSeMEASureHDLCFRAMes SENSeMEASureHDLCFRAMesALL SENSeMEASureIPPACKets SENSeMEASureHDLCBYTesSENSeMEASureIPPACKetsALL SENSeMEASureLINECUMUlative SENSeMEASureLINEWINDow SENSeMEASureLINEWINDowALLSENSeMEASurePATHCUMUlative SENSeMEASurePATHCUMUlativeALL SENSeMEASurePATHWINDowSENSeMEASurePATHWINDowALL SENSeMEASureSECTionCUMUlative SENSeMEASureSECTionCUMUlativeALLSENSeMEASureSECTionWINDow SENSeMEASureWINDowCLEAR SENSeMEASureSECTionWINDowALLSENSeMEASureWINDowLEVEL SENSeMEASureWINDowSIZE SENSeSIGNalSTANdard SENSeOPTicalTHResholdAUTOSENSeOVERheadMONItorCHANnel SENSeSTATusLEDS SENSeSTATusLEDSHEXadecimalSENSeSTATusLEDSNUMEric SENSeSTATusPATHLEDS SENSeSTATusPATHLEDSHEXadecimalSENSeSTATusPATHLEDSNUMEric SENSeTESTMODE SENSeTESTDESCriptionSENSeTESTSTATe SENSeTESTTIME SENSeTRIGgerMODE SENSeTESTTIMEELAPsedSOURceCLOCkSOURce SOURceDATABACKgroundSTRUcture SOURceDATACHANnelREPLicate SOURceDATACHANnelSOURceDATAHDLCIFRameGAP SOURceDATAIPHEADerADDRessDEST SOURceDATAIPHEADerFRAGOFFSet SOURceDATAIPHEADerFLAGSOURceDATAIPHEADerID SOURceDATAIPHEADerPROTocol SOURceDATAIPHEADerTTLive SOURceDATAIPHEADerTSERViceSOURceDATAIPHEADerVERSion SOURceDATAIPPAYLoadPATTern SOURceDATAIPTRAFfic SOURceDATAIPSTReamINDEXSOURceDATAPOSSCRambling SOURceDATAOVERheadPASSthru SOURceDATAOVERheadPASSthruALL SOURceDATAPARItyLOOPSOURceDATAPATHOVERheadPASSthru SOURceDATAPATHOVERheadPASSthruALL SOURceDATAPATHTRACeSOURceDATAPATHTRACeTYPE SOURceDATAPATHTRACeVALUe SOURceDATAPATHTRACeVALUeSTRIngSOURceDATAPAYLoadBACKgroundPATTern SOURceDATAPAYLoadBACKgroundPATTernUDATA SOURceDATAPAYLoadPATTernSOURceDATAPAYLoadPATTernUDATA SOURceDATAPOHBACKgroundBYTEC2A SOURceDATAPOHALLSOURceDATAPOHBYTE SOURceDATAPOHBYTEC2A SOURceDATARATE SOURceDATAPOHDEFAultSOURceDATASECTionTRACe SOURceDATASECTionTRACeTYPE SOURceDATASECTionTRACeVALUeSTRIng SOURceDATASECTionTRACeVALUeSOURceDATASOURce SOURceDATASPEBACKgroundSTUFfing SOURceDATASTRUcture SOURceDATASPESTUFfingSOURceDATATOHSTS1AALL SOURceDATATOHSTS1ABYTE SOURceINSErtANOMalyMODE SOURceDATATOHSTS1ADEFAultSOURceINSErtANOMalyRATE SOURceINSErtANOMalyRATERANGe SOURceINSErtANOMalyREPLicateB2A SOURceINSErtANOMalySTATeSOURceINSErtANOMalyTYPE SOURceINSErtDEFEctMODE SOURceINSErtDEFEctSTATeSOURceINSErtDEFEctTIME SOURceINSErtDEFEctTIMERANGe SOURceINSErtDEFEctTYPESOURceINSertIPANOMalyMODE SOURceINSertIPANOMalyRATERANGe SOURceINSertIPANOMalyRATESOURceINSertIPANOMalyTYPE SOURceMEASureHDLCBYTes SOURceMEASureHDLCFRAMesALL SOURceMEASureHDLCFRAMesSOURceMEASureIPPACKets SOURceMEASureIPPACKetsALL SOURceOUTPutLASerINFOOPTion SOURceSIGNalSTANdardSOURceOUTPutLASerINFOSERial SOURceOUTPutLASerINFOWAVelength SOURceTRIGgerMODE STATusPRESetSYSTemCOMMunicateGPIBPRIMary SYSTemCOMMunicateGPIBSECOndary SYSTemCOMMunicateNETWorkIPPORT SYSTemCOMMunicateNETWorkECHOSYSTemCOMMunicateNETWorkPROMpt SYSTemCOMMunicateNETWorkRXTERM SYSTemCOMMunicateNETWorkTXTERM SYSTemCOMMunicatePORTECHOSYSTemCOMMunicatePORTPROMpt SYSTemCOMMunicatePORTRXTERM SYSTemCOMMunicatePORTTXTERMSYSTemCOMMunicateSERIalCOM1ADTR SYSTemCOMMunicateSERIalCOM1AENABle SYSTemCOMMunicateSERIalCOM1AECHOSYSTemCOMMunicateSERIalCOM1AFLOW SYSTemCOMMunicateSERIalCOM1ANDATA SYSTemCOMMunicateSERIalCOM1ANSTOPSYSTemCOMMunicateSERIalCOM1APARIty SYSTemCOMMunicateSERIalCOM1ARATE SYSTemCOMMunicateSERIalCOM1APROMptSYSTemCOMMunicateSERIalCOM1ARTS SYSTemCOMMunicateSERIalCOM1ARXTERM SYSTemCOMMunicateSERIalCOM1ATXTERM SYSTemCOMMunicateSERIalCOM2AENABleSYSTemCOMMunicateSERIalCOM2ADTR SYSTemCOMMunicateSERIalCOM2AECHO SYSTemCOMMunicateSERIalCOM2AFLOW SYSTemCOMMunicateSERIalCOM2ANDATASYSTemCOMMunicateSERIalCOM2ANSTOP SYSTemCOMMunicateSERIalCOM2APARIty SYSTemCOMMunicateSERIalCOM2APROMptSYSTemCOMMunicateSERIalCOM2ARATE SYSTemCOMMunicateSERIalCOM2ARTS SYSTemCONFigMODuleSERIALSYSTemCOMMunicateSERIalCOM2ARXTERM SYSTemCOMMunicateSERIalCOM2ATXTERM SYSTemCONFigMODuleVARIANT SYSTemCONFigMODuleTYPESYSTemCONFigMODuleVERSion SYSTemCONFigSLOTs SYSTemFILEsMGMTRESUltsAGE SYSTemERRorSYSTemFILEsMGMTRESUltsCOUNt SYSTemFILEsMGMTRESUltsDESTination SYSTemFILEsMGMTRESUltsENABle SYSTemFILEsMGMTRESUltsINTErvalSYSTemFILEsMGMTRESUltsPERcent SYSTemFILEsMGMTRESUltsTOTAlsize SYSTemFILEsMGMTRESUltsSORTSYSTemFORMatBLOCk SYSTemHEADers SYSTemLOCKRELease SYSTemSIGNalSTANdardSYSTemLOCKRELeaseFORCE SYSTemLOCKREQuest TST SYSTemVERBose Reference Remote Commands ~ Command Description Temperature Ranges Environmental SpecificationsDimensions Weight Signal Generation Transmitter SpecificationsInternal Mode Clock Source Through Mode Table A-2 SDH Default Overhead RegeneratorMultiplexer Test Patterns Internal Payload StructuresActive Channel Background Channel Error Injection Overhead Manipulation Specifications Table A-3 Error Rate Max/Min Defect/ Alarm Generation Receiver Analyzer Specifications Alarms DetectionMeasurements Overhead Display OTS91L7, OTS91L8 Signal Name 9.95238 Gb/s Optical Input Transmitter Input and Output Specifications Specifications Event Trigger Output Frame Sync Output External 155.52 MHz Clock Input MHz Trigger OutputTransmitter Data Output Electrical GHz Clock Input GHz Clock Output RX Clock Input Receiver Input and Output Specifications RX Clock OutputRX Data Input Signal Name Tx Data Out / Tx Data Module Interconnect SpecificationsSignal Name Rx Data Out / Rx Data Signal Name Rx Data Out / 10GHz/s Data Certifications and Compliance Laser SafetyCE Mark Compliance EMC Compliance Directive Optical OUT Optical Card Front Panel Descriptions Laser Lockout, Remote Interlock Tx Data Rx Data OUT Optical 10 Gb/s TRANSMIT-ONLY Optics Card L5-15, L5-13 Tx Data Module OK 10Gb/s Optical RECEIVE-ONLY L6 External Laser L7 10Gb/s Optical Transceiver Interface External Laser Figure B-5 shows the Optical Transmitter card front panel 10Gb/s Opticaltransmit ONLY/ External Laser L8 External Laser Emergency Startup Disk Accessing Help Files Emergency Startup Disk List of Acronyms List of Acronyms Tektronix Part Number Description Module Card Replacement Module Card Replacement Installing the Software Installing the Software Illustrations of cabled OTS9100 module Appendix Cabling OTS9100 Module to OTS9261 Tunable Laser Index Index Index-3 Index-4