Tx Data | Tektronix 071-0855-05 guide

Optical Card Front Panel Descriptions

Tx Data IN

Tx Data Input allows electrical data signals to be applied to the optical transmitter. This input must be connected to the Tx Data Out port found on the OTS91Tn Transmitter card of the OTS9100 system using the coax cable provided.

Laser Lockout, Remote Interlock

REMOTE INTERLOCK is a bantam plug normally closed connection internally wired in series with the laser lockout key switch. It can be used with additional hardware to disable the laser output.

NOTE: If this connection is used, the ferrite bead provided with the module must be attached to the remote interlock cable for lower emissions and CE mark conformance. Install the bead close to the end of the cable connected to the Optics card.

Laser LOCKOUT is a safety device. The key switch disables the laser output when it is turned to the “open lock” position. The laser output can only be turned on when the key is in the “closed lock” position.

NOTE: The laser output cannot be enabled unless:

The Laser Lockout key switch is set to the “open lock” or on position.

The Remote Interlock is either not used or externally enabled.

The Laser output is software enabled.

1.NOTE: Optical cables use and care. When using the optical cables ensure that the cable is firmly seated in the front panel connector. The optical connectors on the front panel are keyed. If the cable is not inserted into the connector key properly, the connection between cable and front panel will not be complete and so will cause errors in transmission and receiver functions.

2.Always be sure to clean both cable connectors and front panel connectors before installing optical cables. A dirty optical connection can cause errors in transmission and receiver functions.

OTS9100 User Manual

B-5

Image 234

Tektronix 071-0855-05 user manual Tx Data

Contents

OTS USA Warranty Page Table of Contents Reference Analysis SONET/T1M1 Analysis SDH/G.826 Iii Appendices SOURceDATAPAYLoadBACKgroundPATTern General Safety Summary How to Avoid Fire or Personal Injury General Safety Summary Keep Product Surfaces Clean and Dry Terms in this Manual Safety Terms and SymbolsSymbols on the Product Terms on the Product General Safety Summary Viii Preface How This Manual is Organized Conventions Getting Started Product Description OTS9100 Features and Capabilities Getting Started OTS91L4 Standard AccessoriesStandard with each shipment OTS91L5 Standard OTS91R2 Standard OTS91L7 StandardOTS91L8 Standard OTS91T3 Standard International Power Plug Options Chassis Only Adapters, SMA OTS9100 Installation First Operation Removing Cards Slot Positioning of OTS Cards Multiple Modules OTS9000 with card slot assignment Module Card Interconnection Power On and Software Initialization Proper location Interconnection cables Transmitter Setup Receiver SetupModule Quick Check Getting Started Shutdown and Power Off Emergency Startup Disk Front Panel Indicators and Connectors OTS9100 Front Panel 10Gb/s Transceiver Optics Module OKOptical OUT Tx Data OpticalRx Data OUT Appropriate circuit. -3 1550 nm Transceiver Front Panel Laser Lockout, Remote Interlock Defect indicator will turn off when a new test is started Receive AnalysisModule OK Rx Event OUT Rx DataRx Clock OUT Transmit Generation Tx Event OUTTransmit Front Panel MHz Trig OUT Tx Data OUTGHz Clock GHz Trig OUT Clock TriggerMHz External Clock Rx Clock GHz Clock Out Software Interface Operating Basics Elements of the User Interface System Task BarMenu Bar View Multiple Window Mode View Single ModeMultiple Mode Window Tool Bar Laser Control Bar Main Status Bar ErrorTest Control Bar Client Lockout Test Laser OffFrame Grabbers LED Window User Selected Signal LED Window Module Signal Summary LED PanelSlot Signal LED Panel Clear History Module LED Panel LED Module Display Description of Status Window Virtual LED Indicators SEF OOF Select Signal User Selected Signal Slot Signal LED Display Selection Navigation Window Scroll Buttons Summary Icons Setup Property Menus Signal Standard 10 Transmitter Setup Signal menu Timing Source Bert ModeSignal Source Trigger Output Packet Over Sonet POS SPE/VC3 Stuff Column Control Background Channels Transmitter Transport Overhead 11 Transmitter Transport Overhead menu Edit Overhead 12 Edit Overhead dialog box Through Mode 13 Through Mode Overwrite menu J0 Multi-Byte Trace 14 Transmitter J0 Trace dialog box Transmitter Path Overhead 16 Transmitter Path Overhead Property Menu Path Through Mode Edit Path Overhead J1 Multi-Byte Trace 19 Transmitter J1 Trace dialog box Transmitter Error Insertion 21 Transmitter Error Insertion menu Anomaly Insertion and Through Mode Anomaly Insertion 23 Defect Insertion of the Error Insertion menu Defect Insertion Transmitter K1, K2 Decode 24 Transmitter K1, K2 Decode menu 25 Edit K1, K2 Bytes dialog box Operating Basics User Interface IP Setup Transmitter IP Payload IP Header Transmitter IP Error Insertion Error Selection Current Error Insertion Receiver Signal 26 Receiver Setup Signal menu Signal Structure Test Pattern Receiver Threshold Offset 27 Receiver Threshold Offset dialog box 28 Receiver Setup Trace Mismatch menu Receiver Trace Mismatch Edit C2 Byte 29 J0 Trace Editor dialog box 31 Edit C2 dialog box Hpplm and HP Unequipped Detection Receiver IP Setup Setup Summary 32 Setup Summary menu Signal Monitor Menus Receiver Transport Overhead RS Trace Section Trace J0 S1 Synchronization Status 35 Signal Monitor Path Overhead Receiver Path Overhead Path Trace J1 C2 Status 36 Signal Monitor K1,K2 Decode Receiver K1,K2 Decode 37 Signal Monitor Payload Receiver Payload Test Control Menu 39 Test Control Parameters dialog box Test Control Summary 40 Test Control Summary menu Measurements Menu Receiver Real-Time 42 Real-Time menu Path display Receiver Cumulative 44 Cumulative Measurements Display Section and Line 45 Cumulative Measurements Display Path Receiver History 46 Example of Results History Data Section/Line 47 Example of Results History Data -Path Operating Basics User Interface Receiver IP Measurements Receiver IP Measurements display Transmitter IP Measurements Analysis Menu Analysis SONET/T1M1 49 Analysis menu SONET/T1M1 Path Analysis SDH/G.826 50 Analysis menu SDH/G.826 RS/MS 51 Analysis menu SDH/G.826 Path APS Measurements Menu 52 APS Measurements menu 53 Set APS Test Parameters dialog box 54 Copy APS Measurement Data dialog box Remote Access Setups Select Server Display Notation 59 View Options dialog box Display Configuration Server System System View Scpi Output 63 View Scpi Output dialog box Results Files Results File Management 64 Results File Management dialog box Opening files on the local computer ResultsViewerOperation On the Local computer Connecting to an OTS System Viewing results files 65 Cumulative Results screen of the ResultsViewer Printing results data Configuring ResultsViewerSelecting and arranging windows Exporting test data to other programs Sample output of data from a test results file A202 A604 Record type codes Summary report Test file info Sonet GR-253 Line Analysis History data Configuring the exported data 66 Configure Data Report dialog box Starting the Event Printer program LoggingSelect Events Copy to Printer Copy to ClipboardCopy to File Clear Configuring a printer in Windows Muting Event Printer behavior with continuous eventsMinimizing the Event Printer window 102 Commands Overview Ieee 488.2 System CommandsRemote Control Setup and Format Commands Remote Control Port Settings Remote Control LockoutSystem Configuration Queries Receiver Commands OTS9100 module Save and Restore System SettingsSystem Signal Standard OTS9100 module System File Management Receiver Signal Measurement Commands OTS9100 module Receiver Signal Analysis Commands OTS9100 moduleReceiver Test Control OTS9100 module Transmitter Commands OTS9100 module Syntax Ieee 488.2 Common CommandsCommand and Query Structure Description Block Format Hex Block Format Query format Scpi Commands and QueriesCommand Format Example Parameter types and formats Sourcedatapayloadpattern Enum Optional and alternative parameters #216ABCDEFGHIJKLMNOP Minimum information needed Abbreviating Commands, Queries, and ParametersControlling Responses to Queries Accepted short form Chaining Commands and Queries Example of chaining commands and queries General Rules Slot Specifiers Command Description ESE OPC SENSeANALysisG826AMSFAR SENSeANALysisG826AMSFARALL SENSeANALysisG826AMSNEAR SENSeANALysisG826AMSNEARALLSENSeANALysisG826APATHFAR SENSeANALysisG826APATHFARALL SENSeANALysisG826APATHNEARSENSeANALysisG826APATHNEARALL SENSeANALysisG826ARS SENSeANALysisG826ARSALLSENSeANALysisGR253ALINEFAR SENSeANALysisGR253ALINEFARALL SENSeANALysisGR253ALINENEARSENSeANALysisGR253ALINENEARALL SENSeANALysisGR253APATHFAR SENSeANALysisGR253APATHFARALL SENSeANALysisGR253APATHNEAR SENSeANALysisGR253APATHNEARALL SENSeANALysisGR253ASECTion SENSeANALysisGR253ASECTionALLSENSeANALysisPATHHPPLM SENSeANALysisPATHLABElEXPEcted SENSeANALysisPATHHPPLMGENEricSENSeANALysisPATHHPUNEQ SENSeANALysisPATHTRACeEXPEcted SENSeANALysisPATHTRACeEXPEctedTYPE SENSeANALysisPATHTRACeEXPEctedVALUeSENSeANALysisPATHTRACeEXPEctedVALUeSTRIng SENSeANALysisPATHTRACeTIM SENSeANALysisSECTionTRACeEXPEctedSENSeANALysisSECTionTRACeEXPEctedTYPE SENSeANALysisSECTionTRACeTIM SENSeANALysisSECTionTRACeEXPEctedVALUeSENSeANALysisSECTionTRACeEXPEctedVALUeSTRIng SENSeDATAAUTOscanSTRUcture SENSeDATAIPPAYLoadPATTernUDATA SENSeDATACHANnelSENSeDATAIPPAYLoadPATTern SENSeDATAIPSTReamINDEX SENSeDATAPATHTRACeVALUeSTRIng SENSeDATAPATHTRACeTYPESENSeDATAPATHTRACeVALUe SENSeDATAPAYLoadPATTern SENSeDATAPOHBYTE SENSeDATAPAYLoadPATTernUDATASENSeDATAPOHALL SENSeDATAPOHBYTEC2A SENSeDATASECTionTRACeTYPE SENSeDATARATESENSeDATASECTionTRACe SENSeDATASECTionTRACeVALUe SENSeDATATOHSTM1AALL SENSeDATASPESTUFfingSENSeDATASTRUcture SENSeDATATOHSTS1AALL SENSeINPUtTHREshold SENSeINPutTHResholdLOSSENSeMEASureAPSTimeCONDition SENSeMEASureAPSTimeMAXTime SENSeMEASureAPSTimeRUNSENSeMEASureAPSTimeDETEcted SENSeMEASureAPSTimeSTATus SENSeMEASureHDLCFRAMes SENSeMEASureAPSTimeTHREsholdSENSeMEASureAPSTimeVALUe SENSeMEASureHDLCFRAMesALL SENSeMEASureIPPACKetsALL SENSeMEASureHDLCBYTesSENSeMEASureIPPACKets SENSeMEASureLINECUMUlative SENSeMEASureLINEWINDow SENSeMEASureLINEWINDowALLSENSeMEASurePATHCUMUlative SENSeMEASurePATHCUMUlativeALL SENSeMEASurePATHWINDowSENSeMEASurePATHWINDowALL SENSeMEASureSECTionCUMUlative SENSeMEASureSECTionCUMUlativeALLSENSeMEASureSECTionWINDow SENSeMEASureWINDowLEVEL SENSeMEASureSECTionWINDowALLSENSeMEASureWINDowCLEAR SENSeMEASureWINDowSIZE SENSeSIGNalSTANdard SENSeOPTicalTHResholdAUTOSENSeOVERheadMONItorCHANnel SENSeSTATusLEDS SENSeSTATusLEDSHEXadecimalSENSeSTATusLEDSNUMEric SENSeSTATusPATHLEDS SENSeSTATusPATHLEDSHEXadecimalSENSeSTATusPATHLEDSNUMEric SENSeTESTSTATe SENSeTESTDESCriptionSENSeTESTMODE SENSeTESTTIME SOURceCLOCkSOURce SENSeTESTTIMEELAPsedSENSeTRIGgerMODE SOURceDATABACKgroundSTRUcture SOURceDATAHDLCIFRameGAP SOURceDATACHANnelSOURceDATACHANnelREPLicate SOURceDATAIPHEADerADDRessDEST SOURceDATAIPHEADerID SOURceDATAIPHEADerFLAGSOURceDATAIPHEADerFRAGOFFSet SOURceDATAIPHEADerPROTocol SOURceDATAIPHEADerVERSion SOURceDATAIPHEADerTSERViceSOURceDATAIPHEADerTTLive SOURceDATAIPPAYLoadPATTern SOURceDATAPOSSCRambling SOURceDATAIPSTReamINDEXSOURceDATAIPTRAFfic SOURceDATAOVERheadPASSthru SOURceDATAOVERheadPASSthruALL SOURceDATAPARItyLOOPSOURceDATAPATHOVERheadPASSthru SOURceDATAPATHOVERheadPASSthruALL SOURceDATAPATHTRACeSOURceDATAPATHTRACeTYPE SOURceDATAPATHTRACeVALUe SOURceDATAPATHTRACeVALUeSTRIngSOURceDATAPAYLoadBACKgroundPATTern SOURceDATAPAYLoadBACKgroundPATTernUDATA SOURceDATAPAYLoadPATTernSOURceDATAPAYLoadPATTernUDATA SOURceDATAPOHBYTE SOURceDATAPOHALLSOURceDATAPOHBACKgroundBYTEC2A SOURceDATAPOHBYTEC2A SOURceDATASECTionTRACe SOURceDATAPOHDEFAultSOURceDATARATE SOURceDATASECTionTRACeTYPE SOURceDATASOURce SOURceDATASECTionTRACeVALUeSOURceDATASECTionTRACeVALUeSTRIng SOURceDATASPEBACKgroundSTUFfing SOURceDATATOHSTS1AALL SOURceDATASPESTUFfingSOURceDATASTRUcture SOURceDATATOHSTS1ABYTE SOURceINSErtANOMalyRATE SOURceDATATOHSTS1ADEFAultSOURceINSErtANOMalyMODE SOURceINSErtANOMalyRATERANGe SOURceINSErtANOMalyREPLicateB2A SOURceINSErtANOMalySTATeSOURceINSErtANOMalyTYPE SOURceINSErtDEFEctMODE SOURceINSErtDEFEctSTATeSOURceINSErtDEFEctTIME SOURceINSErtDEFEctTIMERANGe SOURceINSErtDEFEctTYPESOURceINSertIPANOMalyMODE SOURceINSertIPANOMalyTYPE SOURceINSertIPANOMalyRATESOURceINSertIPANOMalyRATERANGe SOURceMEASureHDLCBYTes SOURceMEASureIPPACKets SOURceMEASureHDLCFRAMesSOURceMEASureHDLCFRAMesALL SOURceMEASureIPPACKetsALL SOURceOUTPutLASerINFOSERial SOURceSIGNalSTANdardSOURceOUTPutLASerINFOOPTion SOURceOUTPutLASerINFOWAVelength SYSTemCOMMunicateGPIBPRIMary STATusPRESetSOURceTRIGgerMODE SYSTemCOMMunicateGPIBSECOndary SYSTemCOMMunicateNETWorkPROMpt SYSTemCOMMunicateNETWorkECHOSYSTemCOMMunicateNETWorkIPPORT SYSTemCOMMunicateNETWorkRXTERM SYSTemCOMMunicateNETWorkTXTERM SYSTemCOMMunicatePORTECHOSYSTemCOMMunicatePORTPROMpt SYSTemCOMMunicatePORTRXTERM SYSTemCOMMunicatePORTTXTERMSYSTemCOMMunicateSERIalCOM1ADTR SYSTemCOMMunicateSERIalCOM1AENABle SYSTemCOMMunicateSERIalCOM1AECHOSYSTemCOMMunicateSERIalCOM1AFLOW SYSTemCOMMunicateSERIalCOM1ANDATA SYSTemCOMMunicateSERIalCOM1ANSTOPSYSTemCOMMunicateSERIalCOM1APARIty SYSTemCOMMunicateSERIalCOM1ARTS SYSTemCOMMunicateSERIalCOM1APROMptSYSTemCOMMunicateSERIalCOM1ARATE SYSTemCOMMunicateSERIalCOM1ARXTERM SYSTemCOMMunicateSERIalCOM2ADTR SYSTemCOMMunicateSERIalCOM2AENABleSYSTemCOMMunicateSERIalCOM1ATXTERM SYSTemCOMMunicateSERIalCOM2AECHO SYSTemCOMMunicateSERIalCOM2AFLOW SYSTemCOMMunicateSERIalCOM2ANDATASYSTemCOMMunicateSERIalCOM2ANSTOP SYSTemCOMMunicateSERIalCOM2APARIty SYSTemCOMMunicateSERIalCOM2APROMptSYSTemCOMMunicateSERIalCOM2ARATE SYSTemCOMMunicateSERIalCOM2ARXTERM SYSTemCONFigMODuleSERIALSYSTemCOMMunicateSERIalCOM2ARTS SYSTemCOMMunicateSERIalCOM2ATXTERM SYSTemCONFigMODuleVERSion SYSTemCONFigMODuleTYPESYSTemCONFigMODuleVARIANT SYSTemCONFigSLOTs SYSTemFILEsMGMTRESUltsCOUNt SYSTemERRorSYSTemFILEsMGMTRESUltsAGE SYSTemFILEsMGMTRESUltsDESTination SYSTemFILEsMGMTRESUltsENABle SYSTemFILEsMGMTRESUltsINTErvalSYSTemFILEsMGMTRESUltsPERcent SYSTemFORMatBLOCk SYSTemFILEsMGMTRESUltsSORTSYSTemFILEsMGMTRESUltsTOTAlsize SYSTemHEADers SYSTemLOCKRELeaseFORCE SYSTemSIGNalSTANdardSYSTemLOCKRELease SYSTemLOCKREQuest SYSTemVERBose TST Reference Remote Commands ~ Command Description Dimensions Environmental SpecificationsTemperature Ranges Weight Internal Mode Transmitter SpecificationsSignal Generation Clock Source Through Mode Table A-2 SDH Default Overhead RegeneratorMultiplexer Active Channel Internal Payload StructuresTest Patterns Background Channel Overhead Manipulation Specifications Error Injection Defect/ Alarm Generation Table A-3 Error Rate Max/Min Receiver Analyzer Specifications Alarms DetectionMeasurements Overhead Display Transmitter Input and Output Specifications OTS91L7, OTS91L8 Signal Name 9.95238 Gb/s Optical Input Specifications Frame Sync Output Event Trigger Output Transmitter Data Output Electrical MHz Trigger OutputExternal 155.52 MHz Clock Input GHz Clock Input RX Clock Input GHz Clock Output Receiver Input and Output Specifications RX Clock OutputRX Data Input Signal Name Rx Data Out / Rx Data Module Interconnect SpecificationsSignal Name Tx Data Out / Tx Data Signal Name Rx Data Out / 10GHz/s Data CE Mark Compliance Laser SafetyCertifications and Compliance EMC Compliance Directive Optical Card Front Panel Descriptions Optical OUT Tx Data Laser Lockout, Remote Interlock Optical Rx Data OUT 10 Gb/s TRANSMIT-ONLY Optics Card L5-15, L5-13 Tx Data 10Gb/s Optical RECEIVE-ONLY L6 Module OK 10Gb/s Optical Transceiver Interface External Laser L7 External Laser 10Gb/s Opticaltransmit ONLY/ External Laser L8 Figure B-5 shows the Optical Transmitter card front panel External Laser Accessing Help Files Emergency Startup Disk Emergency Startup Disk List of Acronyms List of Acronyms Module Card Replacement Tektronix Part Number Description Module Card Replacement Installing the Software Installing the Software Appendix Illustrations of cabled OTS9100 module Cabling OTS9100 Module to OTS9261 Tunable Laser Index Index Index-3 Index-4