Agilent Technologies 8935 series e6380a instruction

Error Messages

General Information About Error Messages

• Input value out of range.

A number was entered that was too large or small for the selected field, for example, trying to set AFG1 Freq to 125 kHz.

• Invalid keystroke.

You used a key that has no function relating to the selected field, for example, pressing the On/Off key while the Filter 1 field is selected.

• Option not installed.

You selected a function that requires optional hardware that is not present.

• Turn off either AM or FM settings.

You tried to create simultaneous AM and FM (using any combination of AFGen1, AFGen2, and the Mod In To field). The Test Set does not provide simultaneous AM and FM.

•Squelch interrupt overflow. Reset using Meas Reset (press and release the Shift key, then the Hold key).

The Test Set temporarily interrupts audio measurements when squelch is first broken to prevent internal switching transients from influencing measurements (except when using the SCOPE, SPEC ANL, SERVICE screens). If squelch is repetitively broken in a period of a few seconds, the duration of measurement interruption becomes too great, and the Test Set stops interrupting the signal. Following measurements may be influenced by transient signals.

Meas Reset clears the data buffer used to generate interrupts, resetting the normal squelch operation to eliminate transients.

This condition may occur when monitoring low-level off-the-air signals.

• Cal file checksum incorrect - initializing file.

This error usually occurs after changing the Test Set’s firmware ROM’s. It is not a problem in that instance, but should not re-appear during subsequent operation of the Test Set.

• One or more self tests failed. Error code: XXXX

An instrument failure was detected when the Test Set was turned on. (For example, having a stuck front-panel key during turn on.) The numbered error message corresponds to a binary-weighted group of errors listed in the *TST Common Command description in the Programmer’s Guide.

Chapter 11

305

Image 301

Agilent Technologies 8935 series e6380a manual

Contents

Revision F January Agilent Part Number E6380-90019Page Contents Overview of the Test Set’s Built-In Tools Cdma Measurements Screens and Control Fields Analog Measurements Screens and Control Fields Contents Contents Control Fields on the Configuration Screens 227 Configuration Screens and Control Fields AMPS-TACS, NAMPS-NTACS Encoder and Decoder 253 Signaling Encoder and Decoder Screens and Control Fields Connectors Connectors Error Messages Accessories, Manuals, Support General Information Herstellerbescheinigung Manufacturers Declaration Safety Considerations Adjustments described in the manual are performed with Connected to the earth terminal of the power sourceInstrument must be made inoperative and be secured against Any unintended operation Protective earthing ground incorporated in the power cord This product is a Safety Class I instrument provided with aMains plug shall only be inserted in a socket outlet Provided with a protective earth contact. Any interruption Consumables Lifting and Handling Product Markings Certification Declaration of Conformity Like-new Defects in material and workmanship when properly installedIts programming instructions due to such defects Price upon prompt return of the product Chapter Assistance Regional Sales and Service Office s Power Cables Power CablesStraight/90 8120-1692 Inches, mint gray Used in the following locations Peru Used in the following locations Switzerland Straight/90 8120-4754 Inches, dark gray JIS C 8303, 100 90 /Straight 8120-1351 Inches, mint gray LineNeutral Straight/90 Used in the following locations System Cabinets 8120-4379 Inches, jade gray Power Cables Product Description Sinad SNR Documentation What is in This ManualConventions Used in This Manual Document Navigation Which Document is Required?Document Part Number Usage Trademark Acknowledgments Getting Started Before Connecting a Radio on Before Connecting a Radio Changing the Test Set’s Display Using the cursor-control Knob or Screen Keys To change the measurement screen Unit-of-Measure Field Changing the Control FieldsTo change a unit-of-measure field To Change an underlined entry Underlined Entry Field To make a one-of-many choice One-of-Many Field Numeric-Entry Field Numeric-Entry FieldsTo change a value Hexadecimal Values Decimal Values How do I Verify that the Test Set is Operating Properly? Cdma Spectrum Operating Overview Operating Overview ADC Full Scale ADC FS Displaying Cdma Measurements Magnitude Error, Phase Error Selecting Code Domain Measurements Diagram Transmitter TXPower Frequency Error, FrequencyDisplaying Analog Measurements RF Measurements Displaying AF Measurements Measurement AF Anl In SettingFM Deviation, AM Depth, AC Level SINAD, Distortion, SNR, AF Frequency, DC Level Displaying SINAD, Distortion, SNR, DC Level, or AF Frequency To display the meter scale Displaying Measurement Results on a Meter ScaleTo set the meter’s end points and scale intervals Operating Overview Calibrating the Channel Power Measurement Cdma Analyzer Calibrating the Channel Power Measurement Code Domain Calibrating the Adjacent Channel Power ACP Measurement Using the Factor of 10 Increment/Decrement Keys Changing the Increment or Decrement SettingSpecifying An Increment Value for the Arrow Keys or Knob To reset or remove limits Using Measurement Limit IndicatorsTo set high and low limits To remove a limit To set a reference Setting a Measurement Reference To use measurement averaging Averaging MeasurementsHow the Test Set Averages Measurements To set an RF Offset Setting an RF Generator/Analyzer Offset To save an instrument setup Saving and Recalling Instrument SetupsTo recall an instrument setup Press Recall To remove clear an individual save register Poweron SettingsTo clear all save registers Register Names Memory Considerations Base SettingsInstrument Hardware Changes Using Pre-Defined User Keys Using User Keys To assign local user keys Assigning and Releasing User KeysTo release local user keys To assign global user keys Replacing Batteries Overview of the Test Set’s Overview of theTest Set’s Built-In Tools Using the RF Tools Program Software Menu Screen Loading and Running RF Tools Test Results/BTS Utility Setup Screens Test Results/BTS Utility Setup To use a printer for data collection To use a laptop interface other than the BTS Laptop Utility Swept GainMeasurement Description Making the Measurement Selecting the Swept Gain Measurement Test Level for the Duplex OUT level in dBm parameter Level value to avoid damage to that devicePress k1 Begin Tst Example of a Swept Gain Plot Screen Discrete Frequency Insertion Loss Specifications Particular test Press k1 Proceed when you are finished with this screen.Second display is enlarged for easier reading 10 Selecting the Swept Insertion Loss Measurement Swept Insertion Loss 11 Swept Insertion Loss Setups Estimating Swept Insertion Loss Using a Single Connection Swept Return Loss Select Main Menu Swept Return Loss 13 Swept Return Loss Setups Power level. To avoid damage to the ANT in port, enter an 14 Example of a Swept Return Loss Plot Screen Specifications Test Signal Can Cause Interference Cable FaultTime domain can be used to find the physical distances. Locations by viewing it in units of distance Select Main Menu Cable Fault Measurement Cable length, enter a value 1.5 times the estimated length Greatest accuracy is obtained when you enter a cable lengthToggles the selection between feet and meters K1 HELIAX, k3 RG, or k5 Custom 17 Cable Fault Setups 18 Example of a Cable Fault Plot Screen Cable Fault Performance Typical cable fault return loss measurementsReplot Data Files Select Main Menu 21 Transfer Stored Data Screen Transfer Stored Data 22 SA Self Calibration OFF/ON Screen SA Spectrum Analyzer Self Calibration ON/OFF Catalog PC Memory Card 23 Catalog Memory Card Screen Selecting the Code Domain Analyzer’s Controls Menus Using the Code Domain Analyzer 24 Code Domain Analyzer Menus IS-95 25 Code Domain Analyzer Menus IS-2000 Setting Resolution Bandwidth and Sweep Rate Using the Spectrum AnalyzerRelationship between Span, Resolution Bandwidth, and Sweep Automatic Calibration 26 Spectrum Analyzer Controls Menus Selecting the Spectrum Analyzer’s Controls Menus Delta Frequency Using the Spectrum Analyzer’s Delta MarkersDelta Level Reference Marker Ref Mrkr Level and Frequency Displaying the Spectrum Analyzer Mask Using the Spectrum Analyzer Mask Defining the Fixed Mask’s Limits Settings for mask in FigurePoint Point Level Frequency Turning Off the Mask Defining the Relative Mask’s LimitsTurning Off the Mask’s Failure Beeper Set to Audio Using the Voltmeter and Audio Frequency CounterMeasuring AC and DC Voltages AC Level Set to DC Level or AF Freq Set to match source 29 Inputs and Filters for the Oscilloscope Using the Oscilloscope Scope Selecting the Oscilloscope’s Input Selecting the Oscilloscope’s Filters Using the Oscilloscope’s MarkerTriggering the Oscilloscope Copypl Using Ibutil Programs Securing aTest Procedure Clearing RAM Using the Listopts list options Program Using the Demo Program Step Using the Stplt store or plot Program Cdma Measurements Screens and Control Fields 130 Cdma Measurements Average Power MeasurementsAvg Pwr Screens on which this measurement is displayed Channel Power Measurements Adjacent Channel Power MeasurementsScreens on which this measurement is made Chan Pwr Rho Rho Measurements Estimated Rho Est Rho Frequency Error Freq ErrCode DOM Code Domain Analyzer Time Offset Carrier Feedthrough Chapter 137 Magnitude Error Error Vector Magnitude EVM MeasurementsPhase Error Code Domain Measurements IS-95 Code Domain Power, IS-95 Code DOM Code Domain Analyzer, IS-95 only Selecting Absolute or Relative Code Domain Power, IS-95 only Code Domain Phase Phse Fast PowerCode Domain Timing Timing Code Domain Measurements IS-2000 Advantages of Using IS-2000 Interpreting IS-2000 Channel Ordering Building a tree using the Bit Reverse method Channel numbers. The Walsh index utilizes Walsh orders 0 Available Measurements in the Code Domain 11 Code Domain Power, Bit Reverse Ordering Reading Code Domain Power, IS-2000 Code Domain Power, IS-2000 Code DOM Code Domain Analyzer, IS-2000 Code Domain Power & Noise Code Domain Fast Power Synchronize Code Domain Complex Power PN Offset Search IQ Constellation Diagram, IS-2000 only # of Frames Control Fields for Cdma MeasurementsACP Cal ACP Fltr BW ADCfs or ADC FS ACP OffsetAmplitude Code DOM Code Domain Analyze screen gain controls menu Analyzer code domain analyzer Analyzer Cdma analyzerAnl Dir COD DOM Code Domain Analyzer main controls menu Auto Zero Anl SpecialCarrier FT or Carrier Feedthru Chan Num CD pwr unit Chan SizeChn Pwr Cal CW RF Path ControlsCOD DOM Code Domain Analyzer all menus Data Rate Data Source Find PN Even SecFreq Err Gen Dir GainCOD DOM Code Domain Analyzer gain controls menu Gen Special Gen Mode Input Port Input AttenLvl Code DOM Code Domain Analyzer gain controls menu Marker Lvl Power LevelMarker Pos Meas Intvl or Meas Int Meas Order COD DOM Code Domain Analyzer fast power setup controls menuMeasurement Num Avgs COD DOM Code Domain Analyzer FP setup controls menu Phase/divOfs Trnsfer Output Port PN Incrment PhsePN Offset Pwr Gain PN Offset or PN Ofs Pwr Ref Pwr IntvlPwr Scale IS-95 Pwr Scale IS-2000 Qual Event Pwr Zero Rate RC-4 Rate RC-3Rate RC-5 Code DOM Code Domain Analyzer trigger controls menu RF Gen Freq RF ChannelRF In/Ant Screens on which this field is displayed Start Frame Sprd Fact Spread FactorThreshold Time/div Time Time Ofs Time Offset Tune Freq Trig Event Walsh Order Walsh Chan Control Fields 178 AC Control Analog MeasurementsAM Depth Measurement DC Level Measurement AF Freq Measurement FM Deviation Measurement Distn Distortion Measurement Frequency Measurement Frequency Error Measurement TX Power Measurement Sinad Measurement Is signal to noise ratio of the audio input signalSNR Measurement Control Fields for Analog Measurements Signaling Decoder All Modes#Pts AF Anl AFGen1 Freq AF Cnt Gate AFGen2 Freq AFGen1 To AFGen2 To Signaling Encoder All Modes Spec ANL RF generator controls menu Atten Hold Audio Out Audio In LoAuto/Norm Scope trigger controls menu Spec ANL all menus except mask controls Center FreqSpec ANL main controls menu DC FM Zero Cont/SingleDe-Emp Gain De-Emphasis Display DetectorDetector Types EditPt Edit Mask Ext TTL Ext Load RFilter FM Coupling Freq mask Freq Delta MrkrReference Marker Frequency Level Delta Marker Freq normal marker Spec ANL all menus when in normal mode except mask controlsFreq Ref Mrkr Normal Marker Frequency Level If Filter Gain Cntl Spec ANL auxiliary controls menu Input Gain Internal Level mask Level divLvl Delta Mrkr Lvl normal marker Lvl markerScope all control menus Marker To Peak+ Lvl Ref MrkrMarker To Peak Scope marker controls menu Mask Beep Marker ToMask Type Spec ANL marker controls menu No Pk/Avg Mod In To Norm/Delta Normalize Notch Gain Notch FreqOffset Freq Pk Det To Position Port/SweepScope marker controls menu Spec ANL marker controls menu Ref Level Pos/NegRef Mrkr RF Cnt Gate ResetSpec ANL RF generator or main controls menu Key or turn the Test Set off and on to reset it Maximum signal levels are printed on the connector panelSpec ANL RF Gen controls menu This field selects the input port for the spectrum analyzer Sensitivity RF analyzer Scope To Settling Sensitivity spectrum analyzer Speaker ALC SpanSpeaker Vol Sets the span of frequencies to be displayed on the screen Squelch This field selects the horizontal sweep time per division Track/FixedTime-per-division is selected from a list of choices Scope main controls menu Resolution Trig-Delay TX Pwr Meas Vert/div TX Pwr Zero Vert Offset Configuration Screens 224 Setting the Date and Time Configuring the InstrumentChanging the Beeper’s Volume Turning Off User Messages Printing a Screen Configuring for Printing a ScreenTo interrupt printing Screens Where Field is Present Control Fields on the Configuration ScreensAbort Print Antenna Beeper Base Freq User Defined Chan Space User Defined CallCdma Std 230 Connection Time-out Command Escape CharacterData Length Display User Messages DateDuplex Out FF at End Ext RefFF at Start Firmware OUT connector InaccessibleFlow Control Frame Clock Output Gen-Anl User Defined Gen-Anl Gpib Adrs Hold-off DelayIbasic Echo Inst Echo Incoming Call SecurityLines/Page Mode Model Modem Configuration Modem Mode Modem Initialization/Configuration Number to Call Notch CouplOpt Cdma TB Parity Printer Adrs PasswordPrinter Port Print Title Range Hold Ref Select Remote Mode RF Chan Std Retries RF Gen Volts RF DisplaySee the RF Chan Std on page 244 for more information RF Level Offset RF In/Out Save/Recall RF Offset Serial9 Serial BaudSerial No This field displays the serial number of the Test Set Status Serial PortStop Length Total RAM Signaling Encoder and Decoder Decoder’s Signal Source Signaling Encoder and Decoder ScreensDecoder Frequency Measurements Encoder Control and Voice Channel Identifiers AMPS-TACS, NAMPS-NTACS Encoder and DecoderEncoder/Decoder Interaction AMPS-TACS, NAMPS-NTACS Decoder Decoder Mode DifferencesInterpreting Decoded Data Recc and AMPS-TACS RVC Measurements Decoding the Reverse Control Channel Recc Data Measure Field NAMPS-NTACS Reverse Voice Channel Measurements Decoding NAMPS-NTACS Reverse Voice Channel RVC Data Measurement Limits Dtmf Sequence Encoder and Decoder Decoding Considerations Function Generator Encoder and Decoder Delay Control Fields for the Signaling Encoder and DecoderArm Meas Bursts Busy/Idle Signaling Decoder Modes AMPS-TACS, NAMP-NTACChannel Data hex Signaling Encoder Signaling DecoderData Level Data Rate analog Signaling Decoder Modes NAMP-NTAC Signaling Encoder Modes NAMP-NTACDSAT/DST hex Data you enter here Filler Focc Gate Time FrequencyHi Tone De-emphasis Effects on Input Level Input Level Signaling Decoder All Modes Examples of Input Level SettingsLo Tone Measure AMPS-TACS/NAMPS-NTACS Focc Message and Filler Data Format Message Focc Message FVC AMPS-TACS Signaling Encoder Modes AMPS-TACS Message/DST FVC Message FVC NAMPS-TACS Signaling Encoder Modes Dtmf Signaling Decoder Modes Dtmf Signaling Decoder All Modes Signaling Encoder All ModesNum of Bits Off Time Polarity On TimeNormal Operation Inverted Operation Pre-Emp Signaling Encoder Modes DtmfRecc Data hex SAT Freq FVC Send Dsat FVC SendSend Filler Focc Signaling Encoder Modes Func Gen Send ModeSine Units Single/Cont Stop StandardDecoder Operating Considerations Encoder Operating Considerations Stop Dsat FVC Symbol Frequencies HzStop Filler Focc Stop Meas Trigger Pattern bin Signaling Decoder Modes AMPS-TACS, NAMP-NTAC, Func GenTrig Level Twist and Pre-emphasis Interaction TwistExamples of Twist and Pre-emphasis Interaction Example Waveform Connectors Operating Considerations Connectors ANT Audio Audio OUT Data EXT REF EXT Scope Trig Parallel Port Pin Assignments Parallel RF IN/OUT Serial Port Pin Assignments Serial 9, 10,Serial Port Pin Assignments Pin Description Video OUT Accessories, Manuals, Support Modifications Accessories Agilent Technologies AccessoriesExternal Monitor Agilent Technologies Manuals English and Other Options Agilent Technologies Test SoftwareNumber Description Order Description Number 1D5 High Stability Reference Getting Help Support for Your InstrumentCustomer Training Agilent Regional Sales and Service Offices Error Messages Positive Numbered Error Messages General Information About Error MessagesExample 11-1 Positive numbered error messages take the form Example 11-2 For example Ibasic Error Messages Negative Numbered Error MessagesExample 11-4 Ibasic error messages take the form Example 11-3 For example Text Only Error Messages Gpib Error MessagesExample Gpib error messages take the form Example Text only error messages take the form Message Display Non-Recoverable Firmware ErrorWarbles and Beeps 304 Chapter 305 306 Index 308 Index 309 310 Index 311 312 Index 313 314 Index 315 316 Index 317 318 Index 319 320 Index 321 322 Index 323 324